Lattice Deformation-Induced Enhancement in Thermoelectric Properties of p-Type Bismuth Telluride-Based Alloys

2021 ◽  
Vol 13 (7) ◽  
pp. 1358-1363
Author(s):  
Min Soo Park ◽  
Gook-Hyun Ha ◽  
Yong Ho Park ◽  
Hye Young Koo
Keyword(s):  
Carrier Concentration ◽  
Thermoelectric Properties ◽  
Phonon Scattering ◽  
Thermoelectric Device ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Thermal And Electrical Properties ◽  
P Type ◽  
Short Time ◽  
Sintering Method

ABSTRACTThe properties of a thermoelectric device depend on the thermoelectric material. Bi-Te-based thermoelectric materials consist of p-type and n-type semiconductors are characterized by an excellent dimensionless figure of merit (ZT). In this study, we investigated the effect of the Bi/Sb compositional ratio on the thermoelectric properties in p-type Bi–Sb–Te alloys. Bi–Sb–Te powders were prepared by melting-grinding process. The sintered bodies were fabricated by the spark plasma sintering method, which allows short time sintering for controlling the growth of particles. By controlling the Bi/Sb ratio, the carrier concentration could be optimized. An increase in the Bi concentration led to a decrease in the carrier concentration and thermal conductivity, whereas the See-beck coefficient and specific resistance were increased due to phonon scattering. The thermoelectric ZT value was found to be dependent on changes in the thermal and electrical properties. The best carrier concentration value (2.46 x 1019/cm2) and the highest ZT value (1.3) were achieved for x = 0.4 in BixSb2−xTe3.

Fabrication of Bi-Te Based Thermoelectric Semiconductors by Using Hybrid Powders

2005 ◽  
Vol 297-300 ◽  
pp. 875-880
Author(s):  
Cheol Ho Lim ◽  
Ki Tae Kim ◽  
Yong Hwan Kim ◽  
Dong Choul Cho ◽  
Young Sup Lee ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Single Crystals ◽  
Thermoelectric Properties ◽  
Thermoelectric Materials ◽  
Figure Of Merit ◽  
Bending Strength ◽  
Mixing Ratio ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
P Type

P-type Bi0.5Sb1.5Te3 compounds doped with 3wt% Te were fabricated by spark plasma sintering and their mechanical and thermoelectric properties were investigated. The sintered compounds with the bending strength of more than 50MPa and the figure-of-merit 2.9×10-3/K were obtained by controlling the mixing ratio of large powders (PL) and small powders (PS). Compared with the conventionally prepared single crystal thermoelectric materials, the bending strength was increased up to more than three times and the figure-of-merit Z was similar those of single crystals. It is expected that the mechanical properties could be improved by using hybrid powders without degradation of thermoelectric properties.

Thermoelectric properties of undoped p-type CoSb3 prepared by vertical Bridgman crystal growth and spark plasma sintering

2006 ◽  
Vol 415 (1-2) ◽  
pp. 251-256 ◽  
Author(s):  
Satoru Furuyama ◽  
Tsutomu Iida ◽  
Shinsuke Matsui ◽  
Masayasu Akasaka ◽  
Keishi Nishio ◽  
...  
Keyword(s):  
Crystal Growth ◽  
Spark Plasma Sintering ◽  
Thermoelectric Properties ◽  
Plasma Sintering ◽  
Vertical Bridgman ◽  
Spark Plasma ◽  
Bridgman Crystal Growth ◽  
P Type

The Influence of RuO2 Addition on the Thermoelectric Properties of BiSbTe Alloys

2012 ◽  
Vol 512-515 ◽  
pp. 1651-1654 ◽  
Author(s):  
Yu Kun Xiao ◽  
Zhi Xiang Li ◽  
Jun Jiang ◽  
Sheng Hui Yang ◽  
Ting Zhang ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Thermoelectric Properties ◽  
Lattice Thermal Conductivity ◽  
Combined Process ◽  
Plasma Sintering ◽  
The Matrix ◽  
Spark Plasma ◽  
Xrd Patterns ◽  
Factor Α ◽  
P Type

P-type BiSbTe/RuO2 composite was fabricated using a combined process of melting and spark plasma sintering. The XRD patterns showed that RuO2 reacted with the matrix for the RuO2 content of 1.0 wt% and 4.0 wt% samples. The measured thermoelectric properties showed that the highest electrical conductivity was obtained for the sample with 2.0 wt% RuO2. The power factor (α2σ/κ) decreased with the increase of RuO2 below 450 K. The lattice thermal conductivity was lower than that of BiSbTe over the whole temperature range for BiSbTe/2.0 wt% RuO2.

Thermoelectric properties of In1.3−xSnxSe prepared by spark plasma sintering method

2013 ◽  
Vol 553 ◽  
pp. 270-272 ◽  
Author(s):  
Yongbiao Zhai ◽  
Qiushi Zhang ◽  
Jun Jiang ◽  
Ting Zhang ◽  
Yukun Xiao ◽  
...  
Keyword(s):  
Spark Plasma Sintering ◽  
Thermoelectric Properties ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Sintering Method

scholarly journals Development of Spark Plasma Syntering (SPS) technology for preparation of nanocrystalline p-type thermoelctrics based on (BiSb)2Te3

2020 ◽  
Vol 21 (4) ◽  
pp. 628-634
Author(s):  
O. Kostyuk ◽  
B. Dzundza ◽  
M. Maksymuk ◽  
V. Bublik ◽  
L. Chernyak ◽  
...  
Keyword(s):  
Thermoelectric Properties ◽  
Figure Of Merit ◽  
Antimony Telluride ◽  
Bismuth Antimony Telluride ◽  
Thermoelectric Figure ◽  
Temperature Range ◽  
Plasma Sintering ◽  
Different Temperatures ◽  
Spark Plasma ◽  
P Type

Bismuth antimony telluride is the most commonly used commercial thermoelectric material for power generation and refrigeration over the temperature range of 200–400 K. Improving the performance of these materials is a complected balance of optimizing thermoelectric properties. Decreasing the grain size of Bi0.5Sb1.5Te3 significantly reduces the thermal conductivity due to the scattering phonons on the grain boundaries. In this work, it is shown the advances of spark plasma sintering (SPS) for the preparation of nanocrystalline p-type thermoelectrics based on Bi0.5Sb1.5Te3 at different temperatures (240, 350, 400oC). The complex study of structural and thermoelectric properties of Bi0.5Sb1.5Te3 were presented. The high dimensionless thermoelectric figure of merit ZT ~ 1 or some more over 300–400 K temperature range for nanocrystalline p-type Bi0.5Sb1.5Te3 was obtained.

Study on Phases and Thermoelectric Properties of Bulk FexCo4-xSb12 Sintered by MM-SPS

2011 ◽  
Vol 179-180 ◽  
pp. 294-297
Author(s):  
Ke Gao Liu ◽  
Shi Lei
Keyword(s):  
Thermoelectric Properties ◽  
Thermal Constant ◽  
X Ray Diffraction ◽  
Semiconducting Materials ◽  
X Ray ◽  
Seebeck Coefficients ◽  
Plasma Sintering ◽  
Electrical Resistivities ◽  
Spark Plasma ◽  
P Type

Bulk FexCo4-xSb12 with x varies from 0.1 to 2.0 were prepared by mechanical milling (MM) and spark plasma sintering (SPS). The phases of the products were characterized by X-ray diffraction (XRD) and their thermoelectric properties were tested by electric constant instrument and laser thermal constant instrument. Experimental results show that, the major phases of bulk FexCo4-xSb12 are skutterudite. The electrical resistivities of the products increase first and then decrease. The Seebeck coefficients ( ) are negative when x=0.1 at 100 °C and 200 °C while positive at 300~500 °C. The products with x=0.5~2.0 at 100~500 °C are P type semiconducting materials due to their positive values. The thermal conductivities of most samples increase first and then decrease with x increasing and the maximum is up to 0.39 Wm-1K-1 when x=1.0. The ZT values at 200~500 °C increase first and then decrease with x increasing when x=0.1~1.0 and x=1.0~2.0 respectively and the maximum ZT value is 0.196 when x=1.5 at 400 °C.

Sign in / Sign up

Export Citation Format

Share Document