Viscoelastic behavior of an epoxy resin during cure below the glass transition temperature: Characterization and modeling

2018 ◽  
Vol 53 (2) ◽  
pp. 155-171 ◽  
Author(s):  
Alice Courtois ◽  
Martin Hirsekorn ◽  
Maria Benavente ◽  
Agathe Jaillon ◽  
Lionel Marcin ◽  
...  
Keyword(s):  
Glass Transition ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Epoxy Resin ◽  
Viscoelastic Behavior ◽  
Mechanical Analysis ◽  
Strain History ◽  
Model Parameters ◽  
Degree Of Cure ◽  
Model Predictions

This paper presents a viscoelastic temperature- and degree-of-cure-dependent constitutive model for an epoxy resin. Multi-temperature relaxation tests on fully and partially cured rectangular epoxy specimens were conducted in a dynamic mechanical analysis apparatus with a three-point bending clamp. Master curves were constructed from the relaxation test results based on the time–temperature superposition hypothesis. The influence of the degree of cure was included through the cure-dependent glass transition temperature which was used as reference temperature for the shift factors. The model parameters were optimized by minimization of the differences between the model predictions and the experimental data. The model predictions were successfully validated against an independent creep-like strain history over which the temperature varied.

scholarly journals Studies on the Modification of Commercial Bisphenol-A-Based Epoxy Resin Using Different Multifunctional Epoxy Systems

2021 ◽  
Vol 2 (2) ◽  
pp. 419-430
Author(s):  
Ankur Bajpai ◽  
James R. Davidson ◽  
Colin Robert
Keyword(s):  
Mechanical Properties ◽  
Glass Transition ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Bisphenol A ◽  
Epoxy Resin ◽  
Tensile Fracture ◽  
Chemical Structures ◽  
Amino Phenol ◽  
Epoxy Systems

The tensile fracture mechanics and thermo-mechanical properties of mixtures composed of two kinds of epoxy resins of different chemical structures and functional groups were studied. The base resin was a bi-functional epoxy resin based on diglycidyl ether of bisphenol-A (DGEBA) and the other resins were (a) distilled triglycidylether of meta-amino phenol (b) 1, 6–naphthalene di epoxy and (c) fluorene di epoxy. This research shows that a small number of multifunctional epoxy systems, both di- and tri-functional, can significantly increase tensile strength (14%) over neat DGEBA while having no negative impact on other mechanical properties including glass transition temperature and elastic modulus. In fact, when compared to unmodified DGEBA, the tri-functional epoxy shows a slight increase (5%) in glass transition temperature at 10 wt.% concentration. The enhanced crosslinking of DGEBA (90 wt.%)/distilled triglycidylether of meta-amino phenol (10 wt.%) blends may be the possible reason for the improved glass transition. Finally, the influence of strain rate, temperature and moisture were investigated for both the neat DGEBA and the best performing modified system. The neat DGEBA was steadily outperformed by its modified counterpart in every condition.

Viscoelastic Behavior of Segmented Elastomers

1967 ◽  
Vol 40 (4) ◽  
pp. 1105-1110 ◽  
Author(s):  
Stuart L. Cooper ◽  
Arthur V. Tobolsky
Keyword(s):  
Hydrogen Bonding ◽  
Glass Transition ◽  
High Temperature ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Viscoelastic Behavior ◽  
Temperature Transition ◽  
Hydrogen Bonding Interactions ◽  
Structural Nature ◽  
Hard Segments

Abstract Viscoelastic behavior of linear segmented elastomers was examined. The unusual properties found in spandex systems are also observable in hydrocarbon block co-polymers, indicating that hydrogen bonding interactions are perhaps not essential. Low temperature properties of segmented systems are governed by the structural nature of the associated flexible segments, which determines the value of the major glass transition temperature (Tg). It appears that an association of the hard segments provides a broad temperature range of enhanced rubbery modulus. This occurs between the major Tg and a secondary high temperature transition.

Experimental Research on Mechanical Behavior of GFRP Bars under High Temperature

2011 ◽  
Vol 71-78 ◽  
pp. 3591-3594 ◽  
Author(s):  
Xiao Lu Wang ◽  
Xiao Xiong Zha
Keyword(s):  
Glass Transition ◽  
High Temperature ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Epoxy Resin ◽  
High Temperatures ◽  
Glass Fibers ◽  
Ultimate Tensile Stress ◽  
Gfrp Bars ◽  
Tensile Test Result

Experimental results on tensile mechanics properties of GFRP bars at high temperatures are present in this paper. Thirty commercially produced GFRP tensile specimens of 8mm diameter were tested at high temperature ranging from 10°Cup to 500°C. Tensile test result indicates that, the ultimate tensile stress has significant reduction at two temperature zones, one is glass transition temperature of epoxy resin (80-120°C), with strength degradation 22%, the second is the soften temperature of glass fibers(about 400°C), the strength decrease drastically with almost linear rate and remained 33% residual strength at 500°C. The elastic modulus remained unchanged until glass transition temperature of epoxy resin, and the modulus declined linearly with the temperature elevating. Stress-strain relationships of GFRP bars exhibit liner performance even at high temperatures.

Dynamic mechanical behaviour of kevlar and carbon-kevlar hybrid fibre reinforced polymer composites

2020 ◽  
pp. 095440622097060
Author(s):  
Pragati Priyanka ◽  
Harlal Singh Mali ◽  
Anurag Dixit
Keyword(s):  
Glass Transition ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Dynamic Mechanical Analysis ◽  
Storage Modulus ◽  
Composite Laminates ◽  
Mechanical Analysis ◽  
Textile Composites ◽  
Elastic Behaviour ◽  
Dynamic Mechanical

Comprehensive experimental results of dynamic mechanical analysis (DMA) of polymer reinforced textile composites are presented in the current investigation. Plain and 2x2 twill woven multilayer fabrics of monolithic kevlar and hybrid carbon-kevlar (C-K) are reinforced into the thermoset polymer matrix. Kevlar/epoxy and C-K/epoxy composite laminates are fabricated using an in-house facility of the vacuum-assisted resin infusion process. Variation of the visco-elastic behaviour (storage modulus, damping factor and glass transition temperature, Tg) along with time, temperature and frequency is studied for the composites. Dynamic mechanical analysis is performed under temperature sweep with frequency ranging from 1-50 Hz. Results depict the effect of inter yarn hybridisation of carbon with kevlar yarns on the storage modulus, damping performance, and creep behaviour of dry textile composites. Temperature swept dynamic characterisation is also performed to evaluate the degradation and damping performance of the composite laminates soaked in the deionised water at glass transition temperature Tg, ½ Tg, and ¾ Tg. The morphological study has been performed post the dynamic mechanical analysis using field emission scanning electron microscope.

Influence of Carbon Nanotube Aspect Ratio on Glass Transition Temperature of Polymers: A Molecular Dynamics Simulation Study

2015 ◽  
Vol 817 ◽  
pp. 797-802 ◽  
Author(s):  
Cai Jiang ◽  
Jian Wei Zhang ◽  
Shao Feng Lin ◽  
Su Ju ◽  
Da Zhi Jiang
Keyword(s):  
Molecular Dynamics ◽  
Glass Transition ◽  
Carbon Nanotube ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Aspect Ratio ◽  
Epoxy Resin ◽  
Md Simulations ◽  
Diglycidyl Ether ◽  
Dynamics Simulation

Molecular dynamics (MD) simulations on three single walled carbon nanotube (SWCNT) reinforced epoxy resin composites were conducted to study the influence of SWCNT type on the glass transition temperature (Tg) of the composites. The composite matrix is cross-linked epoxy resin based on the epoxy monomers bisphenol A diglycidyl ether (DGEBA) cured by diaminodiphenylmethane (DDM). MD simulations of NPT (constant number of particles, constant pressure and constant temperature) dynamics were carried out to obtain density as a function of temperature for each composite system. The Tg was determined as the temperature corresponding to the discontinuity of plot slopes of the densityvsthe temperature. In order to understand the motion of polymer chain segments above and below the Tg, various energy components and the MSD at various temperatures of the composites were investigated and their roles played in the glass transition process were analyzed. The results show that the Tg of the composites increases with increasing aspect ratio of the embedded SWCNT

scholarly journals The effective complex permittivity stability in filled polymer nanocomposites studied above the glass transition temperature

2018 ◽  
Vol 149 ◽  
pp. 01080 ◽  
Author(s):  
F. Elhaouzi ◽  
A. Mdarhri ◽  
M. Zaghrioui ◽  
C. Honstettre ◽  
I. El Aboudi ◽  
...  
Keyword(s):  
Glass Transition ◽  
Transition Temperature ◽  
Glass Transition Temperature ◽  
Complex Permittivity ◽  
Dielectric Response ◽  
Volume Fraction ◽  
Three Dimensional ◽  
Mechanical Analysis ◽  
Low Frequencies ◽  
Neat Polymer

The temperature effecton the dielectric response of nanocomposite at low frequencies range is reported. The investigated samples are formed by a semi-crystalline ethylene-co-butyl acrylate (EBA) polymer filled with three concentrations of the dispersed conducting carbon black (CB) nanoparticles. The temperature dependence of the complex permittivity has been analyzedabove the glass transition temperature of the neat polymer matrix Tg=-75°C. For all CB concentrations, the dielectric spectra follow a same trend in frequency range 100-106Hz. More interestingly, the stability of the effective complex permittivity ɛ=ɛ' -iɛ'' with the temperature range of 10-70°C is explored. While the imaginary part of the complex permittivity ɛ'' exhibits a slight decreasewith temperature, the real part ɛ' shows a significant reduction especially for high loading samples. The observed dielectric response may be related to the breakup of the three-dimensional structurenetwork formed by the aggregation of CB particles causing change at the interfaceEBA-CB.This interface is estimated bythe volume fraction of constrained polymer chain according to loss tangent data of dynamic mechanical analysis.

Sign in / Sign up

Export Citation Format

Share Document