The Use of Microcomputer Simulations in Undergraduate Neurophysiology Experiments

1987 ◽  
Vol 14 (3) ◽  
pp. 134-140 ◽  
Author(s):  
K.A. Clarke

Practical classes in neurophysiology reinforce and complement the theoretical background in a number of ways, including demonstration of concepts, practice in planning and performance of experiments, and the production and maintenance of viable neural preparations. The balance of teaching objectives will depend upon the particular group of students involved. A technique is described which allows the embedding of real compound action potentials from one of the most basic introductory neurophysiology experiments—frog sciatic nerve, into interactive programs for student use. These retain all the elements of the “real experiment” in terms of appearance, presentation, experimental management and measurement by the student. Laboratory reports by the students show that the experiments are carefully and enthusiastically performed and the material is well absorbed. Three groups of student derive most benefit from their use. First, students whose future careers will not involve animal experiments do not spend time developing dissecting skills they will not use, but more time fulfilling the other teaching objectives. Second, relatively inexperienced students, struggling to produce viable neural material and master complicated laboratory equipment, who are often left with little time or motivation to take accurate readings or ponder upon neurophysiological concepts. Third, students in institutions where neurophysiology is taught with difficulty because of the high cost of equipment and lack of specific expertise, may well have access to a low cost general purpose microcomputer system.

1994 ◽  
Vol 4 (1) ◽  
pp. 51-54 ◽  
Author(s):  
L.R. Adam ◽  
M.K. Pritchard

An inexpensive system for monitoring and controlling relative humidity (RH) above 90% and for monitoring temperature was developed and tested in a storage research facility for horticultural crops. A general-purpose IBM-PC microcomputer connected to an analog/digital interface system allowed for 16 differential analog inputs and 12 digital outputs for monitoring temperature and RH in eight storage rooms. Relative humidity, measured at 2-min intervals by an inexpensive wet/dry bulb psychrometer in each room, was regulated by a cool-mist humidification system. The standard deviation of RH from set-point was ± 2.8% at 2C and ±3.1% at 10C dry bulb temperature. The software. written in BASIC, allows for additional upgrading to meet future requirements. Commercially available components were used to construct the system at a cost of about Cd$1400 (Canadian) (microcomputer and cool-mist humidification system excluded).


Alloy Digest ◽  
1983 ◽  
Vol 32 (5) ◽  

Abstract AISI 1030 is a plain carbon steel containing nominally 0.30% carbon. It is used in the hot-rolled, normalized, oil-quenched-and-tempered or water-quenched-and-tempered conditions for general-purpose engineering and construction. It provides medium strength and toughness at low cost. Among its many uses are axles, bolts, gears and building sections. All data are on a single heat of fine-grain steel. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness. It also includes information on corrosion resistance as well as forming, heat treating, machining, joining, and surface treatment. Filing Code: CS-94. Producer or source: Carbon and alloy steel mills.


Alloy Digest ◽  
1971 ◽  
Vol 20 (6) ◽  

Abstract AISI 1040 is a medium-carbon steel used in the hot-rolled, normalized, oil quenched and tempered or water quenched and tempered condition for general purpose engineering and construction. It provides medium strength and toughness at low cost. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness and fatigue. It also includes information on corrosion resistance as well as forming, heat treating, machining, joining, and surface treatment. Filing Code: CS-41. Producer or source: Carbon and alloy steel mills.


Alloy Digest ◽  
1979 ◽  
Vol 28 (4) ◽  

Abstract SAE 1037 is a carbon steel that provides medium strength and medium toughness at low cost. It is used in the hot-rolled, normalized, oil-quenched-and-tempered and water-quenched-and-tempered conditions. This medium-carbon steel is used for construction and for general-purpose engineering. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness. It also includes information on corrosion resistance as well as forming, heat treating, machining, joining, and surface treatment. Filing Code: CS-76. Producer or source: Carbon steel mills.


Alloy Digest ◽  
1977 ◽  
Vol 26 (2) ◽  

Abstract SAF 1039 steel can be used in the hot-rolled, normalized, oil-quenched-and-tempered or water-quenched-and-tempered condition for general-purpose construction and engineering. Its manganese content is a little higher than some of the other standard carbon steels with comparable carbon levels; this gives it slightly higher hardenability and hardness. It provides medium strength and toughness at low cost. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness. It also includes information on corrosion resistance as well as forming, heat treating, machining, joining, and surface treatment. Filing Code: CS-66. Producer or source: Carbon steel mills.


Author(s):  
T. N. Antipova ◽  
D. S. Shiroyan

The system of indicators of quality of carbon-carbon composite material and technological operations of its production is proved in the work. As a result of the experimental studies, with respect to the existing laboratory equipment, the optimal number of cycles of saturation of the reinforcing frame with a carbon matrix is determined. It was found that to obtain a carbon-carbon composite material with a low cost and the required quality indicators, it is necessary to introduce additional parameters of the pitch melt at the impregnation stage.


Author(s):  
José Capmany ◽  
Daniel Pérez

Programmable Integrated Photonics (PIP) is a new paradigm that aims at designing common integrated optical hardware configurations, which by suitable programming can implement a variety of functionalities that, in turn, can be exploited as basic operations in many application fields. Programmability enables by means of external control signals both chip reconfiguration for multifunction operation as well as chip stabilization against non-ideal operation due to fluctuations in environmental conditions and fabrication errors. Programming also allows activating parts of the chip, which are not essential for the implementation of a given functionality but can be of help in reducing noise levels through the diversion of undesired reflections. After some years where the Application Specific Photonic Integrated Circuit (ASPIC) paradigm has completely dominated the field of integrated optics, there is an increasing interest in PIP justified by the surge of a number of emerging applications that are and will be calling for true flexibility, reconfigurability as well as low-cost, compact and low-power consuming devices. This book aims to provide a comprehensive introduction to this emergent field covering aspects that range from the basic aspects of technologies and building photonic component blocks to the design alternatives and principles of complex programmable photonics circuits, their limiting factors, techniques for characterization and performance monitoring/control and their salient applications both in the classical as well as in the quantum information fields. The book concentrates and focuses mainly on the distinctive features of programmable photonics as compared to more traditional ASPIC approaches.


2005 ◽  
Vol 33 (1) ◽  
pp. 123-128
Author(s):  
R. P. Grayson ◽  
A. J. Plater

Sign in / Sign up

Export Citation Format

Share Document