A new strategy of reusing abandoned carbon fiber reinforced plastic: Microstructures and properties of C/C composites based on recycled carbon fiber

2020 ◽  
pp. 073168442095944
Author(s):  
Wenjian Guo ◽  
Shuxin Bai ◽  
Yicong Ye
Keyword(s):  
Carbon Fiber ◽  
Bending Strength ◽  
Value Added ◽  
Fiber Reinforced ◽  
Reinforced Plastics ◽  
New Strategy ◽  
Negative Effect ◽  
Ep Matrix ◽  
Carbon Fiber Reinforced ◽  
Interface Bonding Strength

A new strategy of recycling and reusing abandoned carbon fiber reinforced plastics (CFRP) is proposed: CFRPs are first fully carbonized to CF reinforced carbon (C/C) preforms, and then are manufactured into high value-added C/C composites. The results showed that the carbon residue rate of epoxy-resin (EP) matrix was fully recovered as the decomposition route of EP matrix was changed by charring agent. The recycled CF (rCF) was not markedly oxidized or thermally damaged, and possessed comparable properties with those of the virgin CF (vCF) after pyrolysis. The pyrolytic char had no obvious negative effect on the densification efficiency of the rCF reinforced carbon (rCF/C) composites. Both of the rCF/C and vCF reinforced carbon (vCF/C) composite bodies were quite dense, and exhibited almost no difference in their microstructures. The rCF/C and vCF/C composites therefore had quite close interface bonding strength (12.6 MPa and 13.0 MPa, respectively), and bending strength (106.4 MPa and 111.5 MPa, respectively). Furthermore, the rCF/C composites possessed comparable ablative rate with that of the vCF/C composites. The rCF/C composites derived from abandoned CF/EP composites present a great potential to be used as substitutes for vCF/C composites owing to their indistinguishable properties.

Experimental study on the picosecond pulsed laser cutting of carbon fiber-reinforced plastics

2018 ◽  
Vol 37 (15) ◽  
pp. 993-1003 ◽  
Author(s):  
Jun Hu ◽  
Dezhi Zhu
Keyword(s):  
Carbon Fiber ◽  
Bending Strength ◽  
Removal Rate ◽  
Cutting Speed ◽  
Pulsed Laser ◽  
Fiber Reinforced ◽  
Carbon Fiber Reinforced Plastics ◽  
Reinforced Plastics ◽  
Fiber Reinforced Plastics ◽  
Carbon Fiber Reinforced

An experimental investigation of carbon fiber-reinforced plastics cutting with an Nd:YVO4 picosecond pulsed system was presented. One-factor experimental design was used in order to explain the influence of cutting parameters including laser power, hatch distance and cutting speed on the pulsed laser–material interaction. The process parameters were optimized by using central composite design of response surface methodology. The results in kerf width, taper angle, material removal rate, and heat-affected zones were discussed through the micrographs observed with optical microscope. Specimens were cut with three different tools: picosecond pulsed laser, nanosecond pulsed laser, and conventional cutting, and the tensile strength and bending strength tests were conducted. Furthermore, the effect of the heat-affected zones on the static strength was also analyzed.

scholarly journals Performance of 3D-Printed Continuous-Carbon-Fiber-Reinforced Plastics with Pressure

Materials ◽  
2020 ◽  
Vol 13 (2) ◽  
pp. 471 ◽  
Author(s):  
Jun Zhang ◽  
Zude Zhou ◽  
Fan Zhang ◽  
Yuegang Tan ◽  
Yiwen Tu ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Carbon Fiber ◽  
Bending Strength ◽  
Fiber Reinforced ◽  
Carbon Fiber Reinforced Plastics ◽  
Reinforced Plastics ◽  
Continuous Carbon Fiber ◽  
Fiber Reinforced Plastics ◽  
Carbon Fiber Reinforced

Fused Deposition Modeling (FDM) has been investigated as a low-cost manufacturing method for fiber-reinforced composites. The traditional and mature technology for manufacturing continuous-carbon-fiber-reinforced plastics is Automated Fiber Placement (AFP), which uses a consolidation roller and an autoclave process to improve the quality of parts. Compared to AFP, FDM is simple in design and operation but lacks the ability to pressurize and heat the model. In this work, a novel method for printing continuous carbon-fiber-reinforced plastics with a pressure roller was investigated. First, the path processing of the pressure roller was researched, which will reduce the number of rotations of the pressure roller and increase the service life of the equipment and the efficiency of printing. Thereafter, three specimens were printed under different pressures and the tensile and bending strength of specimens were tested. The tensile strength and bending strength of specimens were enhanced to 644.8 MPa and 401.24 MPa by increasing the pressure, compared to the tensile strength and bending strength of specimens without pressure of 109.9 MPa and 163.13 MPa. However, excessive pressure will destroy the path of the continuous carbon fiber (CCF) and the surface quality of the model, and may even lead to printing failure.

scholarly journals Effect of Organo-Modified Montmorillonite Nanoclay on Mechanical, Thermo-Mechanical, and Thermal Properties of Carbon Fiber-Reinforced Phenolic Composites

Polymers ◽  
2021 ◽  
Vol 13 (5) ◽  
pp. 754
Author(s):  
Jantrawan Pumchusak ◽  
Nonthawat Thajina ◽  
Watcharakorn Keawsujai ◽  
Pattarakamon Chaiwan
Keyword(s):  
Thermal Properties ◽  
Carbon Fiber ◽  
Bending Strength ◽  
Mechanical And Thermal Properties ◽  
Fiber Reinforced ◽  
Heat Resistant ◽  
Degradation Temperature ◽  
Modified Montmorillonite ◽  
Carbon Fiber Reinforced ◽  
Montmorillonite Nanoclay

This work aims to explore the effect of organo-modified montmorillonite nanoclay (O-MMT) on the mechanical, thermo-mechanical, and thermal properties of carbon fiber-reinforced phenolic composites (CFRP). CFRP at variable O-MMT contents (from 0 to 2.5 wt%) were prepared. The addition of 1.5 wt% O-MMT was found to give the heat resistant polymer composite optimum properties. Compared to the CFRP, the CFRP with 1.5 wt% O-MMT provided a higher tensile strength of 64 MPa (+20%), higher impact strength of 49 kJ/m2 (+51%), but a little lower bending strength of 162 MPa (−1%). The composite showed a 64% higher storage modulus at 30 °C of 6.4 GPa. It also could reserve its high modulus up to 145 °C. Moreover, it had a higher heat deflection temperature of 152 °C (+1%) and a higher thermal degradation temperature of 630 °C. This composite could maintain its mechanical properties at high temperature and was a good candidate for heat resistant material.

A micromechanical model of carbon fiber-reinforced plastic and steel hybrid laminate composites

2021 ◽  
pp. 002199832110075
Author(s):  
Minchang Sung ◽  
Hyunchul Ahn ◽  
Jinhyeok Jang ◽  
Dongil Kwon ◽  
Woong-Ryeol Yu
Keyword(s):  
Carbon Fiber ◽  
Compressive Stress ◽  
Fracture Strain ◽  
Matrix Material ◽  
Micromechanical Model ◽  
Fiber Reinforced ◽  
Laminate Composites ◽  
Reinforced Plastics ◽  
Carbon Fiber Reinforced ◽  
Hybrid Laminate

The fracture strain of carbon fiber-reinforced plastics (CFRPs) within CFRP/steel hybrid laminate composites is reportedly higher than that of CFRPs due to transverse compressive stress induced by the steel lamina. A micromechanical model was developed to explain this phenomenon and also to predict the mechanical behavior of CFRP/steel hybrid laminate composites. First, the shear lag theory was extended to calculate stress distributions on fibers and matrix material in a CFRP under multiaxial stress condition, considering three deformation states of matrix (elastic and plastic deformation and fracture) and the transverse compressive stress. Then, the deformation behavior of CFRP was predicted using average stress in the ineffective region and the Weibull distribution of carbon fibers. Finally, the mechanical properties of CFRP/steel hybrid laminate composites were predicted by considering the thermal residual stress generated during the manufacturing process. The micromechanical model revealed that increased transverse compressive stress decreases the ineffective lengths of partially broken fibers in the CFRP and results in increased fracture strain of the CFRP, demonstrating the validity of the current micromechanical model.

INCREASING SENSITIVITY OF EDDY CURRENT NON-DESTRUCTIVE TESTING OF DELAMINATION IN CARBON-FIBER REINFORCED PLASTICS

2021 ◽  
pp. 28-37
Author(s):  
P. N. Shkatov ◽  
G. A. Didin ◽  
A. A. Ermolaev
Keyword(s):  
Carbon Fiber ◽  
Eddy Current ◽  
Calculation Model ◽  
Fiber Reinforced ◽  
Destructive Testing ◽  
Carbon Fiber Reinforced Plastics ◽  
Reinforced Plastics ◽  
Fiber Reinforced Plastics ◽  
Carbon Fiber Reinforced ◽  
The Difference

The paper is concerned with increasing sensitivity of eddy current nondestructive testing of most dangerous delamination in carbon-fiber reinforced plastics (CFRP). Increased sensitivity is achieved by separate registration and comparison of eddy current signals obtained from a set of stratifications of carbon fibers with the same orientation. The separation of eddy current signals is possible due to pronounced anisotropy of the electrical conductivity of the layers dominant in the direction of the fibers of the corresponding layer. Eddy-current signals are registered by eddy current probes with maximum sensitivity in a given angular direction. Prior to the scan eddy current signals of the probe are leveled on a defect-free area. The influence of the working gap on the difference between the eddy current signals of the probe is suppressed by normalizing it according to one of the signals. The analysis of the registered signals from delamination has been performed using an approximate calculation model. The reliability of the obtained results has been confirmed by comparison with experimental results and calculations using the finite element method.

Sign in / Sign up

Export Citation Format

Share Document