Numerical investigation of the effects of immersion on the efficiency of a tidal helical turbine

2018 ◽  
Vol 233 (12) ◽  
pp. 4299-4310 ◽  
Author(s):  
Hamid Rahmani ◽  
Mojtaba Biglari ◽  
Mohammad Sadegh Valipour ◽  
Kamran Lari
Keyword(s):  
Numerical Investigation ◽  
Single Phase ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Volume Of Fluid Method ◽  
Two Phase ◽  
Ansys Fluent ◽  
Full Immersion ◽  
High Torque ◽  
Horizontal Axis Turbine

In the current study, a two-phase simulation of a tidal helical turbine was performed that contrasts with previous studies in two ways. First, the current research simulated the turbine in different states of immersion in water, whereas previous studies simulated turbines mostly in single-phase conditions and full immersion in water. Second, the present study used a horizontal-axis turbine, whereas previous research employed a vertical-axis helical turbine or Darrius turbine. In this study, a simulation was conducted using the volume of fluid method in ANSYS Fluent 18. Results indicated that the complete immersion of the turbine in water generated a high torque, thereby reducing the efficiency of the device. To determine the conditions with the highest efficiency, immersion rates of 100%, 75%, 50%, and 25% in water were examined, and a configuration with best power coefficient ( C p = 0.175 in TSR = 0.47) was found in 25% immersion. In immersion rate of 25%, resistant pressure on blades was minimum.

scholarly journals Numerical Study on the Tandem Submerged Hydrofoils Using RANS Solver

2021 ◽  
Vol 2021 ◽  
pp. 1-17
Author(s):  
Moloud Arian Maram ◽  
Hamid Reza Ghafari ◽  
Hassan Ghassemi ◽  
Mahmoud Ghiasi
Keyword(s):  
Drag Coefficient ◽  
Single Phase ◽  
Two Phase Flow ◽  
Numerical Study ◽  
Lift Coefficient ◽  
Lower Surface ◽  
Phase Flow ◽  
Two Phase ◽  
Hydrodynamic Coefficient ◽  
Ansys Fluent

This paper is presented on the tandem two-dimensional hydrofoils with profiles NACA4412 in single-phase and two-phase flow domains for different submergence depths and different distances in a various angle of attack (AoA). Also, supercavitation is studied at σ = 0.34 by the Zwart cavitation model. Reynolds-averaged Navier–Stokes (RANS) with the shear stress transport (SST) K-ω is employed as a turbulence model in transient analysis of Ansys FLUENT software. The numerical results show that, by increasing depth, the drag coefficient increases for both hydrofoils 1 and 2 as well as the lift coefficient. The drag coefficient of hydrofoil 2 is bigger than hydrofoil 1 for all depths; moreover, it was found that the flow pressure behind the hydrofoil 1 had affected the upper and the lower surface of the hydrofoil 2 at each distance or AoA. These effects are observed in the hydrofoil 2 lift coefficient as well as the flow separation. However, the maximum lift-to-drag ratio is observed at AoA =  8 ° and 3.5c distance. Also, single-phase results reveal that the value of pressure and the hydrodynamic coefficient are very different from the two-phase flow results, due to the elimination of the free surface. So, a two-phase flow domain is recommended for increasing the accuracy of results. In addition, the investigation of supercavitation shows a growth in cavity occurrence on the surface by raising AoA.

Alternative Blade Profile based on Savonius Concept for Effective Wind Energy Harvesting

2021 ◽  
pp. 1-32
Author(s):  
Parag K. Talukdar ◽  
Nur Alom ◽  
Umang H. Rathod ◽  
Vinayak Kulkarni
Keyword(s):  
Vertical Axis ◽  
Rotor Blades ◽  
Power Coefficient ◽  
Potential Candidate ◽  
Blade Profile ◽  
Ansys Fluent ◽  
Pressure Distributions ◽  
Bladed Rotor ◽  
Identical Test ◽  
Experimental Findings

Abstract The drag-based vertical-axis Savonius wind rotor is a potential candidate for harvesting renewable energy. It is very simple in design and can be deployed as an off-the-grid electricity system in remote locations having no access to electricity. The present work aims to develop a novel blade profile for the Savonius rotor in order to improve its performance. In that connection, an arc-elliptical-blade profile has been developed and rotor performance has been assessed through wind tunnel testing at three different Reynolds numbers (Re = 87039, 107348, and 131066). Further, its performance is compared to that of a conventional semicircular-bladed rotor under identical test conditions. The experiments revealed the maximum power coefficient (CPmax) of 0.11, 0.162, 0.213 at Re = 87039, 107348, and 131066, respectively for the arc-elliptical-bladed rotor. To complement the experimental findings and to examine the flow behaviour around the rotor blades, the computational fluid dynamics (CFD) simulations have also been performed using ANSYS FLUENT software. The local torque is found to be greater around the advancing arc-elliptical blade than around the advancing semicircular blade. It has been also noticed that the pressure distributions over concave sides are similar regardless of the blade shape.

Simulation Study on the Performance of Vertical Axis Wind Turbine

2013 ◽  
Vol 465-466 ◽  
pp. 270-274 ◽  
Author(s):  
N. Afzanizam Samiran ◽  
A.A. Wahab ◽  
Mohd Sofian ◽  
N. Rosly
Keyword(s):  
Output Power ◽  
Flow Characteristic ◽  
Cfd Simulation ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Navier Stokes ◽  
Vertical Axis Wind Turbine ◽  
Ansys Fluent ◽  
Savonius Rotor ◽  
Torque Coefficient

The present study considered the design improvement of Savonius rotor, in order to increase the efficiency of output power. An investigation was conducted to study the effect of geometrical configuration on the performance of the rotor in terms of coefficient of torque, coefficient of power and power output. Modification of conventional geometry has been designed by combining the effect of number of blades and shielding method. CFD simulation was conducted to analyze the flow characteristic and calculate the torque coefficient of all the rotor configurations. The continuity and Reynolds Averaged Navier-Stokes (RANS) equations and realizable k-ε epsilon turbulence model are numerically solved by commercial software Ansys-Fluent 14.0. The results obtained by transient and steady method for the conventional two bladed Savonius rotor are in agreement with those obtained experimentally by other authors and this indicates that the methods can be successfully applied for such analysis. The modified 3 and 4 bladed rotors with hybrid shielding method gave the highest maximum power coefficient which 0.37 at TSR 0.5 and output power exceed 4 watts with rotor dimensions of 0.2m width and 0.2m height. This blade configuration also is the best configuration by several percentages compared to the other model from the previous study

scholarly journals Numerical efficiency evaluation of a vertical axis turbine equipped with 4 digits and 5 digits NACA airfoils

2019 ◽  
Vol 85 ◽  
pp. 03001
Author(s):  
Florina Costea ◽  
Ion Malael
Keyword(s):  
Wind Turbine ◽  
Vertical Axis ◽  
Scientific Paper ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Renewable Energy Resources ◽  
Ansys Fluent ◽  
Sst Turbulence Model ◽  
Fluent Software ◽  
Shape Influence

In the current age of global energy crisis, a run for the use of renewable energy resources as the wind energy has gained a significant attention. The main objective of this study is the comparison between two wind turbine configurations. These two turbines have the same geometric parameters but one with a 4 digits NACA0018 blades and the other with 5 digits NACA63-415 blades. In this scientific paper, a numerical evaluation of the airfoil shape influence on the VAWT efficiency is done. For this study the CFD methods with Ansys Fluent software, are used. All the simulations are for unsteady flow at 1e06 Reynolds number value with SST turbulence model. At the design point the wind velocity is 12 m/s and for the wind turbine geometric features, the diameter is 3.25m and the height 4.87m. The power coefficient variation through tip speed ratio will be represented for each wind turbine configurations. To estimate the recirculation zone effects on the efficiency, the vorticity magnitude contours are presented for different positions of the blades. The results will indicate the feasibility of optimization of future wind turbine more complex airfoils.

Numerical Simulations of Spherical Vertical-Axis Wind Rotor

2013 ◽  
Vol 291-294 ◽  
pp. 456-460
Author(s):  
Yong Yu Huang ◽  
Qiu Yun Mo ◽  
Xu Zhang ◽  
Zu Peng Zhou
Keyword(s):  
Numerical Simulation ◽  
Aspect Ratio ◽  
Flow Simulation ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Projected Area ◽  
Simulation Code ◽  
Ansys Fluent ◽  
Identical Number

In this paper, the effects of the shape of three types of the blade on power coefficient of Savonius rotors are studied by simulating the model using numerical simulation under the same conditions. For this purpose, three spherical rotors with different configurations but identical number of stages and blades, aspect ratio and overlap keeping the identical projected area of each rotor are constructed. The geometries of blade of the three rotors are a plane, a semi-circle and a quarter of sphere. The building data are calculated on the basis of the nominal wind velocity V= 10m/s and the speed ratio λ= 0.3 with an industrial flow simulation code (ANSYS-Fluent). The result shows that the rotor with semicircular blades has a higher value of power coefficient in comparison with other rotors.

scholarly journals Design and numerical analysis of an efficient H-Darrieus vertical-axis hydrokinetic turbine

2019 ◽  
Vol 13 (4) ◽  
pp. 6036-6058
Author(s):  
Ramirez D. ◽  
Rubio-Clemente A. ◽  
E. Chica
Keyword(s):  
Rural Communities ◽  
Three Dimensional ◽  
Vertical Axis ◽  
Turbine Rotor ◽  
Power Coefficient ◽  
Stream Velocity ◽  
Ansys Fluent ◽  
Electrical Grid ◽  
2D Simulation ◽  
Hydrokinetic Turbine

Hydrokinetic turbines are one of the technological alternatives to generate and supply electricity for rural communities isolated from the national electrical grid with almost zero emission. The Darrieus turbine is one of the options that can be used as a hydrokinetic turbine due to its high power coefficient (Cp) and easy manufacture. In the present work, the design and hydrodynamic analysis of a Darrieus vertical-axis hydrokinetic turbine of 500 W was carried out. A free stream velocity of 1.5 m/s was used for the design of the blades. The diameter (D) and blade length (H) of the turbine were 1.5 m and 1.13 m, respectively. The blade profile used was NACA0025 with a chord length of 0.33 m and solidity () of 0.66. Two (2D) and three dimensional (3D) numerical analyses of the unsteady flow through the blades of the turbine were performed using ANSYS Fluent version 18.0, which is based on a Reynolds-Averaged Navier-Stokes (RANS) model. A transient 2D simulation was conducted for several tip speed ratios (TSR) using a k-ω Shear Stress Transport turbulence (SST) scheme. The optimal TSR was found to be around 1.75. Main hydrodynamic parameters, such as torque (T) and CP, were investigated. Additionally, 3 geometrical configurations of the turbine rotor were studied using a 3D numerical model in order to identify the best configuration with less Cp and T fluctuation. The maximum Cp average was 0.24 and the amplitude of Cp variation, near 0.24 for the turbine model with 3 blades of H equal to 1.13 m. On the other hand, for the turbine models with 6 and 9 blades of H equal to 0.565 m and 0.377 m, respectively, the maximum Cp averages were 0.51 and 0.55, respectively, and the amplitude of Cp variation, near 0.07 for the model with 6 blades and 0.17 for the model with 9 blades. This revealed that the hydrokinetic turbine with a geometrical configuration of 6 blades greatly improves the performance of the turbine due to this model has advantages compared to models with 3 and 9 blades, in terms of the reduction of their T curve fluctuation.

scholarly journals Studi simulasi penggunaan airfoil naca 6412 sebagai sudu pada turbin angin crossflow melalui pemodelan CFD 2 dimensi

2018 ◽  
Vol 13 (1) ◽  
pp. 28
Author(s):  
Muhammad Ivan Fadhil Hendrawan ◽  
Dominicus Danardono ◽  
Syamsul Hadi
Keyword(s):  
Wind Turbine ◽  
Constant Velocity ◽  
Cross Flow ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Ansys Fluent ◽  
Tip Speed Ratio ◽  
Blade Number

AbstractThe simulation aimed to understand the effect of the angle of blade number and blade number of vertical axis wind turbine with cross flow runner to enhance the performance of wind turbine. The turbine had 20, 22, and 24 number of blades. Simulation was done in 2D analysis using ANSYS-Fluent. Tip speed ratio was varied in range of 0,1-0,5 with constant velocity inlet 2 m/s. The effect of blade numbers to torque and power coefficient were analyzed and compared. It had been found that the best power coefficient were 0,5 at tip speed ratio 0,3.

Numerical Investigation of Modified Bach Type Vertical Axis Wind Turbine

2016 ◽  
Vol 852 ◽  
pp. 551-557 ◽  
Author(s):  
R. Sarath Kumar ◽  
T. Micha Premkumar ◽  
Sivamani Seralathan ◽  
T. Mohan
Keyword(s):  
Wind Turbine ◽  
Vertical Axis ◽  
Flow Behaviour ◽  
Power Coefficient ◽  
Navier Stokes ◽  
Vertical Axis Wind Turbine ◽  
Navier Stokes Equation ◽  
Ansys Fluent ◽  
Improved Performance ◽  
And Performance

This study evaluates the performance and flow behaviour over the modified Bach type Vertical Axis Wind Turbine. A two dimensional unsteady state analysis is carried out in this study. The unsteady Reynolds Averaged Navier-Stokes equation and the turbulence equation corresponding to SST k-ω turbulence model are solved using commercial software ANSYS FLUENT 13. A grid independence study is performed to choose optimum mesh elements. The simulation is carried out and performance parameters like power coefficient and torque coefficient are calculated. The results are compared with the available experimental data for validation purpose and these matched with numerical values. An improved performance of around 37% Cp is observed for modified Bach type over simple Savonius rotor. Moreover, a brief analysis of flow behaviour over the rotor is studied.

Sign in / Sign up

Export Citation Format

Share Document