scholarly journals Numerical study on aerodynamic performance of waverider with a new bluntness method

2020 ◽  
pp. 095441002096841
Author(s):  
Zhipeng Qu ◽  
Houdi Xiao ◽  
Mingyun Lv ◽  
Guangli Li ◽  
Cui Kai
Keyword(s):  
Numerical Study ◽  
Leading Edge ◽  
Aerodynamic Characteristics ◽  
Aerodynamic Performance ◽  
The Novel ◽  
High Lift ◽  
Wide Range ◽  
Drag Ratio ◽  
Lift To Drag Ratio ◽  
Sharp Leading Edge

Abastrct The waverider is deemed the most promising configuration for hypersonic vehicle with its high lift-to-drag ratio at design conditions. However, considering the serious aero-heating protection, the sharp leading edge must be blunted. The existing traditional bluntness methods including the following two types: “reducing material method” and “adding material method”. Compared to the initial waverider, the volume will be smaller or larger using the traditional methods. With the fixed blunted radius, the volume and aerodynamic performance is determined. In this paper, a new bluntness method which is named “mixing material method” is developed. In this new method, a new parameter is introduced based on the traditional two bluntness methods. Under fixed blunted radius, the volume and aerodynamic performance can be changed within a wide range by adjusting the parameter. When the parameter is 0 and 1, the novel blunted method degenerated into the “reducing material method” and “adding material method” respectively. The influence of new parameter on the aerodynamic characteristics and volume are studied by numerical simulation. Results show that the volume, lift and lift-to-drag ratio increases with the increase of the parameter under the fixed blunt radius, but simultaneously, the drag will also increase. Therefore, considering the different requirements of the air-breathing hypersonic aircrafts for the balance of thrust and drag, lift and weight, a suitable bluntness parameter can be selected to achieve a balance. This research can provide reference for hypersonic waverider vehicle design.

Modification impact on aerodynamic performance of hypersonic waverider

2011 ◽  
Vol 115 (1168) ◽  
pp. 325-334 ◽  
Author(s):  
C. Xiao-Qing ◽  
H. Zhong-Xi ◽  
L. Jian-Xia ◽  
G. Xian-Zhong
Keyword(s):  
Leading Edge ◽  
Aerodynamic Performance ◽  
Hypersonic Vehicles ◽  
Flow Conditions ◽  
Aerodynamic Coefficient ◽  
High Lift ◽  
Computational Fluid Dynamics Cfd ◽  
Drag Ratio ◽  
Lift To Drag Ratio ◽  
Sharp Leading Edge

Abstract Waverider serves as a good candidate for hypersonic vehicles. The typical waverider has sharp leading edge and no control face, which is inappropriate for practical use. This paper puts forward a method modifying the waverider, and the modification impact on the performance of waverider at hypersonic flow conditions is studied. The modification is based on blunted waverider, includes cutting the tip and introducing two control wings. The modification’s effect on aerodynamic performance is obtained and analysed through Computational Fluid Dynamics (CFD) techniques. When blunted with 2cm radius, the waverider retains its good aerodynamic performance and the heat flux at the stagnation point can be managed. Three factors of the introduced wing are argued, the fixed angle, aspect ratio and wing area. Results show that influence on the aerodynamic coefficient is slight and the vehicle retains its high lift-to-drag ratio. The main influences of the modification are the control ability and trim efficiency, which is the motivation of this work and can be adapted when designing a practical waverider.

Comparison between Methods of Generation of Waveriders Derived from Streamline Tracing and Simplified Method

2013 ◽  
Vol 390 ◽  
pp. 134-140
Author(s):  
Feng Ding ◽  
Jun Liu ◽  
Liang Jin ◽  
Shi Bin Luo
Keyword(s):  
Aerodynamic Characteristics ◽  
Aerodynamic Performance ◽  
High Lift ◽  
Shape Factors ◽  
Simplified Method ◽  
Streamline Tracing ◽  
Simulation Results ◽  
Drag Ratio ◽  
Lift To Drag Ratio ◽  
Tracing Method

Waverider with a high lift-to-drag ratio has drawn an ever increasing attention. Usually, waverider is obtained by tracing streamline. A simplified generation method of waverider is introduced in the present paper named geometric relations method. Three groups of cone-derived waverider configuration, respectively, based on the geometric relations method and the streamline tracing method are generated for the comparisons of the shape factors, inviscid aerodynamic characteristics, and flow field structures by investigating the numerical simulation results. The results show that the effect of the Mach number and the shock angle on the differences caused by the two methods are not significantly different. While the volumetric efficiency of the waverider configuration based on the geometric relations method is larger than those based on the streamline tracing, the inviscid lift-to-drag ratio of the former is less than the latter. Although the geometric relations method is much easier than the streamline tracing method, the simplified method reduces the aerodynamic performance of the waverider configuration.

Roughness Sensitivity Considerations for Thick Rotor Blade Airfoils

2003 ◽  
Vol 125 (4) ◽  
pp. 468-478 ◽  
Author(s):  
R. P. J. O. M. van Rooij ◽  
W. A. Timmer
Keyword(s):  
Turbine Blades ◽  
Leading Edge ◽  
Lower Surface ◽  
Vortex Generators ◽  
Wind Turbine Blades ◽  
High Lift ◽  
Edge Roughness ◽  
Proper Design ◽  
Drag Ratio ◽  
Lift To Drag Ratio

In modern wind turbine blades, airfoils of more than 25% thickness can be found at mid-span and inboard locations. At mid-span, aerodynamic requirements dominate, demanding a high lift-to-drag ratio, moderate to high lift and low roughness sensitivity. Towards the root, structural requirements become more important. In this paper, the performance for the airfoil series DU FFA, S8xx, AH, Risø and NACA are reviewed. For the 25% and 30% thick airfoils, the best performing airfoils can be recognized by a restricted upper-surface thickness and an S-shaped lower surface for aft-loading. Differences in performance of the DU 91-W2-250 (25%), S814 (24%) and Risø-A1-24 (24%) airfoils are small. For a 30% thickness, the DU 97-W-300 meets the requirements best. Reduction of roughness sensitivity can be achieved both by proper design and by application of vortex generators on the upper surface of the airfoil. Maximum lift and lift-to-drag ratio are, in general, enhanced for the rough configuration when vortex generators are used. At inboard locations, 2-D wind tunnel tests do not represent the performance characteristics well because the influence of rotation is not included. The RFOIL code is believed to be capable of approximating the rotational effect. Results from this code indicate that rotational effects dramatically reduce roughness sensitivity effects at inboard locations. In particular, the change in lift characteristics in the case of leading edge roughness for the 35% and 40% thick DU airfoils, DU 00-W-350 and DU 00-W-401, respectively, is remarkable. As a result of the strong reduction of roughness sensitivity, the design for inboard airfoils can primarily focus on high lift and structural demands.

420 Aerodynamic Characteristics and Flow Field of High Lift-to-drag Ratio Airfoils in Low Reynolds Number

2015 ◽  
Vol 2015.68 (0) ◽  
pp. 167-168 ◽  
Author(s):  
Takahiro MAKIZONO ◽  
Gaku SASAKI ◽  
Hiroshi OCHI ◽  
Takaaki MATSUMOTO ◽  
Koichi YONEMOTO
Keyword(s):  
Reynolds Number ◽  
Flow Field ◽  
Low Reynolds Number ◽  
Aerodynamic Characteristics ◽  
High Lift ◽  
Low Reynolds ◽  
Drag Ratio ◽  
Lift To Drag Ratio

Numerical Study of Improving Aerodynamic Performance of the Cylinder Airfoil of Magnus Wind Turbine

2013 ◽  
Vol 650 ◽  
pp. 414-419
Author(s):  
Qi Yao ◽  
Ying Xue Yao ◽  
Liang Zhou ◽  
Jin Ming Wu ◽  
Jian Guang Li
Keyword(s):  
Fluid Dynamics ◽  
Drag Force ◽  
Numerical Study ◽  
Rotating Cylinder ◽  
Aerodynamic Performance ◽  
Orthogonal Test ◽  
Performance Change ◽  
Result Show ◽  
Drag Ratio ◽  
Lift To Drag Ratio

To solve the problem of low lift to drag ratio of Magnus cylinder airfoil, the Computational Fluid Dynamics software Fluent was used to study the principle of a drop of the drag force of cylinder when rotating. And the principle was used to further reduce the drag of rotating cylinder. A traditional airfoil head and a triangle tail was used to study the effect of the aerodynamic performance change of the combined airfoil. A conclusion was made that with a suitable profile of the tail would reduce the drag force of the combined airfoil thus increase the lift to drag ratio of the airfoil. At last an orthogonal test was made to determine the size of the tail airfoil. The result show that the optimized airfoil reduce the drag force to 50% of the original cylinder and improve the lift to drag ratio to 50%.

scholarly journals RESEARCH OF WING DIHEDRAL ANGLE EFFECT ON AERODYNAMIC PERFORMANCE OF TANDEM-WING UNMANNED AERIAL VEHICLE

2013 ◽  
pp. 90-101
Author(s):  
І. С. Кривохатько
Keyword(s):  
Dihedral Angle ◽  
Aerodynamic Characteristics ◽  
Aerodynamic Performance ◽  
Theoretical Explanation ◽  
Wing Span ◽  
Induced Drag ◽  
Rear Wing ◽  
Angle Effect ◽  
Drag Ratio ◽  
Lift To Drag Ratio

In the last decade folding tube launch UAV became common, for which aerodynamic scheme "tandem" is reasonable. By the time tandem-wing aerodynamic characteristics are researched much less than ones of traditional scheme. Particularly it concerns wing dihedral angle effect on lift-to-drag ratio about which no quantitative data were found.Forward or rear wing dihedral angle appearance result in circulation redistribution and changing of rear wing induced drag. Rear wing dihedral angle effect on longitudinal aerodynamic performance of tandem-wing UAV model was researched through wind tunnel experiment. Geometry variables were forward and rear wing spans, rear wing dihedral angle and longitudinal stagger. Lift, drag and longitudinal moment coefficients were defined.The possibility of lift-to-drag ratio increasing at cruise regime was proofed. Rear wing negative dihedral angle application is able to increase maximal lift-to-drag ratio by more than 1.0 or about 10 %.It was found that wing dihedral angle effectiveness depends from relation of forward and rear wing spans and from longitudinal stagger. Longitudinal stagger increasing results in dihedral angle effectiveness falling if forward wing span is higher than rear wing. For bigger rear wing span increasing of longitudinal stagger results in dihedral angle effectiveness gaining. The hypothesis was declared that proposes theoretical explanation of experimentally founded dependencies.Also dihedral angle appearance increases lift slope because of rear wing carrying capacity gain and has almost no influence on maximal lift coefficient.All dependencies founded for rear wing negative dihedral angle are correct for forward wing positive dihedral angle except the last one is increasing longitudinal and lateral stability.

Roughness Sensitivity Considerations for Thick Rotor Blade Airfoils

2003 ◽  
Author(s):  
R. P. J. O. M. van Rooij ◽  
W. A. Timmer
Keyword(s):  
Rotor Blade ◽  
Turbine Blades ◽  
Leading Edge ◽  
Lower Surface ◽  
Wind Turbine Blades ◽  
Strong Reduction ◽  
High Lift ◽  
Edge Roughness ◽  
Drag Ratio ◽  
Lift To Drag Ratio

In modern wind turbine blades airfoils of more than 25% thickness can be found at mid-span and inboard locations. In particular at mid-span aerodynamic requirements dominate, demanding a high lift-to-drag ratio, moderate to high lift and low roughness sensitivity. Towards the root srtuctural requirements become more important. In this paper the performance for the airfoil series DU, FFA, S8xx, AH, Riso̸ and NACA are reviewed. For the 25% and 30% thick airfoils the best performing airfoils can be recognized by a restricted upper surface thickness and a S-shaped lower surface for aft-loading. Differences in performance of the DU 91-W2-250 (25%), S814 (24%) and Riso̸-A1-24 (24%) airfoil are small. For a 30% thickness the DU 97-W-300 meets the requirements best. At inboard locations the influence of rotation can be significant and 2d wind tunnel tests do not represent the characteristics well. The RFOIL code is believed to be capable of approximating the rotational effect. In particular the change in lift characteristics in the case of leading edge roughness for the 35% and 40% thick DU airfoils, respectively DU 00-W-350 and DU 00-W–401, is remarkable. Due to the strong reduction of roughness sensitivity the design for inboard airfoils could primarily focus on high lift and structural demands.

scholarly journals Shock Reduction through Opposing Jets—Aerodynamic Performance and Flight Stability Perspectives

2019 ◽  
Vol 10 (1) ◽  
pp. 180 ◽  
Author(s):  
Shagufta Rashid ◽  
Fahad Nawaz ◽  
Adnan Maqsood ◽  
Rizwan Riaz ◽  
Shuaib Salamat
Keyword(s):  
Pressure Ratio ◽  
Leading Edge ◽  
Aerodynamic Performance ◽  
Navier Stokes ◽  
Flight Stability ◽  
Supersonic Regime ◽  
Free Stream Mach Number ◽  
Drag Ratio ◽  
First Time ◽  
Lift To Drag Ratio

In this research paper, investigations of counter flow (opposing) jet on the aerodynamic performance, and flight stability characteristics of an airfoil with blunt leading-edge in supersonic regime are performed. Unsteady Reynolds-Averaged Navier-Stokes ( U R A N S ) based solver is used to model the flow field. The effect of angle of attack ( α ), free-stream Mach number ( M ∞ ), and pressure ratio ( P R ) on aerodynamic performance of airfoil with and without jet are compared. The results indicate that the opposing jet reduces drag from 30 % to 70 % , improves the maximum lift-to-drag ratio from 2.5 to 4.0, and increases shock stand-off distance from 15 % to 35 % depending on flow conditions. The effect of opposing jet on longitudinal flight stability characteristics, studied for the first time, indicate improvement in dynamic stability coefficients ( C m q + C m α ˙ ) at low angles of attack. It is concluded that the opposing jet can help mitigate flight disturbances in supersonic regime.

Aerodynamic Performance of Blended Wing Body Aircraft with Distributed Propulsion

2014 ◽  
Vol 1016 ◽  
pp. 354-358 ◽  
Author(s):  
Wan Fang Yan ◽  
Jiang Hao Wu ◽  
Yan Lai Zhang
Keyword(s):  
Lift Coefficient ◽  
Large Angle ◽  
Aerodynamic Performance ◽  
Propulsion System ◽  
System Configuration ◽  
High Lift ◽  
Distributed Propulsion ◽  
Drag Ratio ◽  
Lift To Drag Ratio ◽  
Center Body

A 350-passenger BWB with a distributed propulsion system configuration is carried out and its aerodynamic performance in cruising and taking off are analyzed and discussed. It is shown from computation that the integrated configuration has a commendable aerodynamic performance in cruising and taking off. The cruise lift to drag ratio is reach to 24.0 in cruising. The ingestion effect of the propulsion system leads to a high lift at a low speed. The maximum lift coefficient CLmax is 1.62 when α=20° in taking off. In addition, the ingestion also delays the flow separation on the upper surface of center body, which contributes to a well stall performance of the configuration at large angle of attack.

Sign in / Sign up

Export Citation Format

Share Document