Numerical Study of Improving Aerodynamic Performance of the Cylinder Airfoil of Magnus Wind Turbine

2013 ◽  
Vol 650 ◽  
pp. 414-419
Author(s):  
Qi Yao ◽  
Ying Xue Yao ◽  
Liang Zhou ◽  
Jin Ming Wu ◽  
Jian Guang Li
Keyword(s):  
Fluid Dynamics ◽  
Drag Force ◽  
Numerical Study ◽  
Rotating Cylinder ◽  
Aerodynamic Performance ◽  
Orthogonal Test ◽  
Performance Change ◽  
Result Show ◽  
Drag Ratio ◽  
Lift To Drag Ratio

To solve the problem of low lift to drag ratio of Magnus cylinder airfoil, the Computational Fluid Dynamics software Fluent was used to study the principle of a drop of the drag force of cylinder when rotating. And the principle was used to further reduce the drag of rotating cylinder. A traditional airfoil head and a triangle tail was used to study the effect of the aerodynamic performance change of the combined airfoil. A conclusion was made that with a suitable profile of the tail would reduce the drag force of the combined airfoil thus increase the lift to drag ratio of the airfoil. At last an orthogonal test was made to determine the size of the tail airfoil. The result show that the optimized airfoil reduce the drag force to 50% of the original cylinder and improve the lift to drag ratio to 50%.

scholarly journals Numerical study on aerodynamic performance of waverider with a new bluntness method

2020 ◽  
pp. 095441002096841
Author(s):  
Zhipeng Qu ◽  
Houdi Xiao ◽  
Mingyun Lv ◽  
Guangli Li ◽  
Cui Kai
Keyword(s):  
Numerical Study ◽  
Leading Edge ◽  
Aerodynamic Characteristics ◽  
Aerodynamic Performance ◽  
The Novel ◽  
High Lift ◽  
Wide Range ◽  
Drag Ratio ◽  
Lift To Drag Ratio ◽  
Sharp Leading Edge

Abastrct The waverider is deemed the most promising configuration for hypersonic vehicle with its high lift-to-drag ratio at design conditions. However, considering the serious aero-heating protection, the sharp leading edge must be blunted. The existing traditional bluntness methods including the following two types: “reducing material method” and “adding material method”. Compared to the initial waverider, the volume will be smaller or larger using the traditional methods. With the fixed blunted radius, the volume and aerodynamic performance is determined. In this paper, a new bluntness method which is named “mixing material method” is developed. In this new method, a new parameter is introduced based on the traditional two bluntness methods. Under fixed blunted radius, the volume and aerodynamic performance can be changed within a wide range by adjusting the parameter. When the parameter is 0 and 1, the novel blunted method degenerated into the “reducing material method” and “adding material method” respectively. The influence of new parameter on the aerodynamic characteristics and volume are studied by numerical simulation. Results show that the volume, lift and lift-to-drag ratio increases with the increase of the parameter under the fixed blunt radius, but simultaneously, the drag will also increase. Therefore, considering the different requirements of the air-breathing hypersonic aircrafts for the balance of thrust and drag, lift and weight, a suitable bluntness parameter can be selected to achieve a balance. This research can provide reference for hypersonic waverider vehicle design.

scholarly journals Numerical Analysis of Effect of Leading-Edge Rotating Cylinder on NACA0021 Symmetric Airfoil

2019 ◽  
Vol 4 (7) ◽  
pp. 11-17
Author(s):  
Md. Abdus Salam ◽  
Vikram Deshpande ◽  
Nafiz Ahmed Khan ◽  
M. A. Taher Ali
Keyword(s):  
Free Stream ◽  
Numerical Study ◽  
Tangential Velocity ◽  
Leading Edge ◽  
Rotating Cylinder ◽  
Aerodynamic Performance ◽  
Stream Velocity ◽  
Surface Boundary ◽  
Lower Velocity ◽  
Numerical Studies

The moving surface boundary control (MSBC) has been a Centre stage study for last 2-3 decades. The preliminary aim of the study was to ascertain whether the concept can improve the airfoil characteristics. Number of experimental and numerical studies pointed out that the MSBC can superiorly enhance the airfoil performance albeit for higher velocity ratios (i.e. cylinder tangential velocity to free stream velocity). Although abundant research has been undertaken in this area on different airfoil performances but no attempt was seen to study effect of MSBC on NACA0021 airfoil for and also effects of lower velocity ratios. Thus, present paper focusses on numerical study of modified NACA 0021 airfoil with leading edge rotating cylinder for velocity ratios (i.e.) between 1 to 1.78 at different angles of attack. The numerical study indicates that the modified airfoil possess better aerodynamic performance than the base airfoil even at lower velocity ratios (i.e. for velocity ratios 0.356 and beyond). The study also focusses on reason for improvement in aerodynamic performance by close look at various parameters.

The aerodynamic optimisation of a low-Reynolds paper plane with adjoint method

2020 ◽  
pp. 1-15
Author(s):  
Y. Zhang ◽  
X. Zhang ◽  
G. Chen
Keyword(s):  
Adjoint Method ◽  
Low Cost ◽  
Aerodynamic Performance ◽  
Discrete Adjoint ◽  
Design Variables ◽  
Limited Variation ◽  
Aerial Vehicle ◽  
Paper Plane ◽  
Drag Ratio ◽  
Lift To Drag Ratio

ABSTRACT The aerodynamic performance of a deployable and low-cost unmanned aerial vehicle (UAV) is investigated and improved in present work. The parameters of configuration, such as airfoil and winglet, are determined via an optimising process based on a discrete adjoint method. The optimised target is locked on an increasing lift-to-drag ratio with a limited variation of pitching moments. The separation that will lead to a stall is delayed after optimisation. Up to 128 design variables are used by the optimised solver to give enough flexibility of the geometrical transformation. As much as 20% enhancement of lift-to-drag ratio is gained at the cruise angle-of-attack, that is, a significant improvement in the lift-to-drag ratio adhering to the preferred configuration is obtained with increasing lift and decreasing drag coefficients, essentially entailing an improved aerodynamic performance.

Numerical Study of Winglet Cant Angle Effect on Wing Performance at Low Reynolds Number

2013 ◽  
Vol 393 ◽  
pp. 366-371
Author(s):  
C.F. Mat Taib ◽  
Abdul Aziz Jaafar ◽  
Salmiah Kasolang
Keyword(s):  
Reynolds Number ◽  
Numerical Analysis ◽  
Numerical Study ◽  
Low Reynolds Number ◽  
Lift Coefficient ◽  
Wing Model ◽  
Low Reynolds ◽  
Wing Performance ◽  
Drag Ratio ◽  
Lift To Drag Ratio

The study on the effect of winglet shape in wing design has been a focus of many researchers. Nevertheless, the effect of cant angle on the wing performances at low Reynolds number has not been fully explored. This paper describes the effect of a single semi-circular shaped winglet attached with a rectangular wing model to lower the drag without increasing the span of the wing. Aerodynamic characteristics for the rectangular wing (NACA 65-3-218) with and without semi-circular winglets have been studied using STAR CCM+ 4.0. This numerical analysis is based on Finite Volume Approach. Simulations were carried out on the rectangular wing model with and without winglet at aspect ratio of 2.73 and Reynolds number of 0.16 x 10 6 for various angles of attack. From the numerical analysis, wing performance characteristics in terms of lift coefficient CL, drag coefficient CD, and lift-to-drag ratio, CL/CD were obtained. It was found that the addition of a semi-circular winglet has resulted in a larger lift curve slope and higher Lift-to-Drag ratio in comparison with the case of a wing without winglet. Further investigation has revealed that a wing with semi-circular winglet with cant angle of 45 degree has produced the best Lift-to-Drag ratio, CL/CD.

Numerical exploration on drag and heat reduction mechanism of a spike-tipped supersonic blunt nose

2020 ◽  
Vol 34 (32) ◽  
pp. 2050370
Author(s):  
Yu-Shan Meng ◽  
Li Yan ◽  
Shi-Bin Li ◽  
Wei Huang
Keyword(s):  
Heat Flux ◽  
Drag Force ◽  
Stokes Equations ◽  
Angle Of Attack ◽  
Three Dimensional ◽  
Viscous Force ◽  
Reduction Mechanism ◽  
Complex Flow ◽  
Drag Ratio ◽  
Lift To Drag Ratio

In this study, the drag force and heat flux reduction mechanism induced by the aerodisk (with disks on its nose) with the freestream Mach number being 4.937 has been numerically investigated, and the simulations have been carried out by the three-dimensional Reynolds-averaged Navier–Stokes equations coupled with the SST [Formula: see text] turbulence model. The influence of the angle of attack on the drag and heat flux reduction has been analyzed comprehensively. The obtained results show that the drag force of the spiked blunt body can be reduced by the aerodisk, and the drag force decreases by 24.63%. The flow mechanism of the complex flow is drastically modified by the angle of attack, and this results in a strong flow asymmetry. This asymmetry becomes more and more obvious as the angle of attack increases. Both the pressure force and viscous force increase with the increase of the angle of attack. Moreover, both the lift and drag coefficients increase as the angle of attack increases, and the lift-to-drag ratio increases first and then decreases with the increase of the angle of attack. When the angle of attack is [Formula: see text], the maximum lift-to-drag ratio is close to 0.36.

Research on Improved Method of Wind Turbine Airfoil S834 Based on Noise and Aerodynamic Performance

2015 ◽  
Vol 744-746 ◽  
pp. 253-258 ◽  
Author(s):  
Ya Qiong Chen ◽  
Yue Fa Fang
Keyword(s):  
Wind Turbine ◽  
Optimization Design ◽  
Design Method ◽  
Aerodynamic Performance ◽  
Parametric Modeling ◽  
Multi Objective ◽  
Wind Turbine Airfoil ◽  
Drag Ratio ◽  
Operating Points ◽  
Lift To Drag Ratio

In this paper, aerodynamic performance and noise of the wind turbine airfoil are the optimization design goal and based on this, the optimization design method with multi-operating points and multi-objective of the airfoils is built. The Bezier curve is used in parametric modeling of the contour of the airfoil and the general equation for control points is deduced form the discrete points coordinates of the airfoil. The weigh distribution schemes for multi-objective and multi-operating points are integrated designed by treating the NREL S834 airfoil as the initial airfoils. The results show that the lift-to-drag ratio of the optimized airfoils has a improvement around the designed operating angle and the overall noise has a reduction compared with the initial airfoils, which means that the optimized airfoils get a better aerodynamic and acoustic performance.

Modification impact on aerodynamic performance of hypersonic waverider

2011 ◽  
Vol 115 (1168) ◽  
pp. 325-334 ◽  
Author(s):  
C. Xiao-Qing ◽  
H. Zhong-Xi ◽  
L. Jian-Xia ◽  
G. Xian-Zhong
Keyword(s):  
Leading Edge ◽  
Aerodynamic Performance ◽  
Hypersonic Vehicles ◽  
Flow Conditions ◽  
Aerodynamic Coefficient ◽  
High Lift ◽  
Computational Fluid Dynamics Cfd ◽  
Drag Ratio ◽  
Lift To Drag Ratio ◽  
Sharp Leading Edge

Abstract Waverider serves as a good candidate for hypersonic vehicles. The typical waverider has sharp leading edge and no control face, which is inappropriate for practical use. This paper puts forward a method modifying the waverider, and the modification impact on the performance of waverider at hypersonic flow conditions is studied. The modification is based on blunted waverider, includes cutting the tip and introducing two control wings. The modification’s effect on aerodynamic performance is obtained and analysed through Computational Fluid Dynamics (CFD) techniques. When blunted with 2cm radius, the waverider retains its good aerodynamic performance and the heat flux at the stagnation point can be managed. Three factors of the introduced wing are argued, the fixed angle, aspect ratio and wing area. Results show that influence on the aerodynamic coefficient is slight and the vehicle retains its high lift-to-drag ratio. The main influences of the modification are the control ability and trim efficiency, which is the motivation of this work and can be adapted when designing a practical waverider.

scholarly journals RESEARCH OF WING DIHEDRAL ANGLE EFFECT ON AERODYNAMIC PERFORMANCE OF TANDEM-WING UNMANNED AERIAL VEHICLE

2013 ◽  
pp. 90-101
Author(s):  
І. С. Кривохатько
Keyword(s):  
Dihedral Angle ◽  
Aerodynamic Characteristics ◽  
Aerodynamic Performance ◽  
Theoretical Explanation ◽  
Wing Span ◽  
Induced Drag ◽  
Rear Wing ◽  
Angle Effect ◽  
Drag Ratio ◽  
Lift To Drag Ratio

In the last decade folding tube launch UAV became common, for which aerodynamic scheme "tandem" is reasonable. By the time tandem-wing aerodynamic characteristics are researched much less than ones of traditional scheme. Particularly it concerns wing dihedral angle effect on lift-to-drag ratio about which no quantitative data were found.Forward or rear wing dihedral angle appearance result in circulation redistribution and changing of rear wing induced drag. Rear wing dihedral angle effect on longitudinal aerodynamic performance of tandem-wing UAV model was researched through wind tunnel experiment. Geometry variables were forward and rear wing spans, rear wing dihedral angle and longitudinal stagger. Lift, drag and longitudinal moment coefficients were defined.The possibility of lift-to-drag ratio increasing at cruise regime was proofed. Rear wing negative dihedral angle application is able to increase maximal lift-to-drag ratio by more than 1.0 or about 10 %.It was found that wing dihedral angle effectiveness depends from relation of forward and rear wing spans and from longitudinal stagger. Longitudinal stagger increasing results in dihedral angle effectiveness falling if forward wing span is higher than rear wing. For bigger rear wing span increasing of longitudinal stagger results in dihedral angle effectiveness gaining. The hypothesis was declared that proposes theoretical explanation of experimentally founded dependencies.Also dihedral angle appearance increases lift slope because of rear wing carrying capacity gain and has almost no influence on maximal lift coefficient.All dependencies founded for rear wing negative dihedral angle are correct for forward wing positive dihedral angle except the last one is increasing longitudinal and lateral stability.

CFD analysis of variable geometric angle winglets

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Ali Hussain Kazim ◽  
Abdullah Hamid Malik ◽  
Hammad Ali ◽  
Muhammad Usman Raza ◽  
Awais Ahmad Khan ◽  
...  
Keyword(s):  
Aerodynamic Performance ◽  
Sweep Angle ◽  
Content Type ◽  
Wing Model ◽  
Induced Drag ◽  
Computational Fluid Dynamics Analysis ◽  
Attached Flow ◽  
Drag Ratio ◽  
Fuel Costs ◽  
Lift To Drag Ratio

Purpose Winglets play a major role in saving fuel costs because they reduce the lift-induced drag formed at the wingtips. The purpose of this paper is to obtain the best orientation of the winglet for the Office National d’Etudes et de Recherches Aérospatiales (ONERA) M6 wing at Mach number 0.84 in terms of lift to drag ratio. Design/methodology/approach A computational fluid dynamics analysis of the wing-winglet configuration based on the ONERA M6 airfoil on drag reduction for different attack angles at Mach 0.84 was performed using analysis of systems Fluent. First, the best values of cant and sweep angles in terms of aerodynamic performance were selected by performing simulations. The analysis included cant angle values of 30°, 40°, 45°, 55°, 60°, 70° and 75°, while for the sweep angles 35°, 45°, 55°, 65° and 75° angles were used. The aerodynamic performance was measured in terms of the obtained lift to drag ratios. Findings The results showed that slight alternations in the winglet configuration can improve aerodynamic performance for various attack angles. The best lift to drag ratio for the winglet was achieved at a cant angle of 30° and a sweep angle of 65°, which caused a 5.33% increase in the lift to drag ratio. The toe-out angle winglets as compared to the toe-in angles caused the lift to drag ratio to increase because of more attached flow at its surface. The maximum value of the lift to drag ratio was obtained with a toe-out angle (−5°) at an angle of attack 3° which was 2.53% greater than the zero-toed angle winglet. Originality/value This work is relatively unique because the cant, sweep and toe angles were analyzed altogether and led to a significant reduction in drag as compared to wing without winglet. The wing model was compared with the results provided by National Aeronautics and Space Administration so this validated the simulation for different wing-winglet configurations.

scholarly journals Shock Reduction through Opposing Jets—Aerodynamic Performance and Flight Stability Perspectives

2019 ◽  
Vol 10 (1) ◽  
pp. 180 ◽  
Author(s):  
Shagufta Rashid ◽  
Fahad Nawaz ◽  
Adnan Maqsood ◽  
Rizwan Riaz ◽  
Shuaib Salamat
Keyword(s):  
Pressure Ratio ◽  
Leading Edge ◽  
Aerodynamic Performance ◽  
Navier Stokes ◽  
Flight Stability ◽  
Supersonic Regime ◽  
Free Stream Mach Number ◽  
Drag Ratio ◽  
First Time ◽  
Lift To Drag Ratio

In this research paper, investigations of counter flow (opposing) jet on the aerodynamic performance, and flight stability characteristics of an airfoil with blunt leading-edge in supersonic regime are performed. Unsteady Reynolds-Averaged Navier-Stokes ( U R A N S ) based solver is used to model the flow field. The effect of angle of attack ( α ), free-stream Mach number ( M ∞ ), and pressure ratio ( P R ) on aerodynamic performance of airfoil with and without jet are compared. The results indicate that the opposing jet reduces drag from 30 % to 70 % , improves the maximum lift-to-drag ratio from 2.5 to 4.0, and increases shock stand-off distance from 15 % to 35 % depending on flow conditions. The effect of opposing jet on longitudinal flight stability characteristics, studied for the first time, indicate improvement in dynamic stability coefficients ( C m q + C m α ˙ ) at low angles of attack. It is concluded that the opposing jet can help mitigate flight disturbances in supersonic regime.

Sign in / Sign up

Export Citation Format

Share Document