Influence of different blade numbers on the performance of “saddle zone” in a mixed flow pump

2021 ◽  
pp. 095765092110460
Author(s):  
Leilei Ji ◽  
Wei Li ◽  
Weidong Shi ◽  
Fei Tian ◽  
Shuo Li ◽  
...  
Keyword(s):  
Flow Field ◽  
Leading Edge ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Mixed Flow ◽  
Impeller Blade ◽  
Flow Angle ◽  
Tip Leakage ◽  
Vorticity Transport ◽  
Flow Pump

In order to study the effect of different numbers of impeller blades on the performance of mixed-flow pump “saddle zone”, the external characteristic test and numerical simulation of mixed-flow pumps with three different impeller blade numbers were carried out. Based on high-precision numerical prediction, the internal flow field and tip leakage flow field of mixed flow pump under design conditions and stall conditions are investigated. By studying the vorticity transport in the stall flow field, the specific location of the high loss area inside the mixed flow pump impeller with different numbers of blades is located. The research results show that the increase in the number of impeller blades improve the pump head and efficiency under design conditions. Compared to the 4-blade impeller, the head and efficiency of the 5-blade impeller are increased by 5.4% and 21.9% respectively. However, the increase in the number of blades also leads to the widening of the “saddle area” of the mixed-flow pump, which leads to the early occurrence of stall and increases the instability of the mixed-flow pump. As the mixed-flow pump enters the stall condition, the inlet of the mixed-flow pump has a spiral swirl structure near the end wall for different blade numbers, but the depth and range of the swirling flow are different due to the change in the number of blades. At the same time, the change in the number of blades also makes the flow angle at 75% span change significantly, but the flow angle at 95% span is not much different because the tip leakage flow recirculates at the leading edge. Through the analysis of the vorticity transport results in the impeller with different numbers of blades, it is found that the reasons for the increase in the values of the vorticity transport in the stall condition are mainly impacted by the swirl flow at the impeller inlet, the tip leakage flow at the leading edge and the increased unsteady flow structures.

Influence of tip leakage flow and inlet distortion flow on a mixed-flow pump with different tip clearances within the stall condition

2019 ◽  
Vol 234 (4) ◽  
pp. 433-453 ◽  
Author(s):  
Leilei Ji ◽  
Wei Li ◽  
Weidong Shi
Keyword(s):  
Internal Flow ◽  
Energy Performance ◽  
Rotating Stall ◽  
Design Flow ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Mixed Flow ◽  
Tip Leakage ◽  
Flow Pump

In order to investigate the effect of impeller tip clearance on internal flow fields and the rotating stall inception impacted by tip leakage vortex and inlet unsteady flow in a mixed-flow pump, mixed-flow pump models with tip clearances of 0.5 mm, 0.8 mm, and 1.1 mm were numerically calculated, and then the energy performance curves and internal flow structures were obtained and compared. The results show that the pump efficiency and the internal flow fields of numerical calculation are in good agreement with experimental results at design flow rate and near-stall condition. A portion of the positive slope segment appears in the energy performance curves under different tip clearances. The lowest head of the mixed-flow pump in the positive slope region decreases with the increase of the tip clearance while the highest head shows an opposite situation indicating that mixed-flow pumps are easier to stall under small tip clearance. At the design flow rate condition, the tip leakage vortex is relatively stable under different tip clearances and appears as a “snail shell” shape, whereas in rotating stall conditions, the “snail shell” shape disappear and the tip leakage flow on blade front forms a “flat” vortex structure. The inlet swirl flow not only affects the tip leakage flow in rotating stall conditions under different tip clearances, but also blocks the fluid from the inlet pipe. Under the circumstance of the same tip clearance, the main frequency amplitude of pressure pulsation coefficient gradually shifts away from blade passing frequency (96.67 Hz) to the axial frequency (24.17 Hz) when the pump operates in the stall condition.

scholarly journals Vortex Dynamics Analysis of Internal Flow Field of Mixed-Flow Pump under Alford Effect

Water ◽  
2021 ◽  
Vol 13 (24) ◽  
pp. 3575
Author(s):  
Shuo Li ◽  
Wei Li ◽  
Leilei Ji ◽  
Weidong Shi ◽  
Ramesh K. Agarwal
Keyword(s):  
Flow Field ◽  
Vortex Core ◽  
Guide Vane ◽  
Internal Flow ◽  
Tip Leakage Flow ◽  
Mixed Flow ◽  
Tip Leakage ◽  
L1 And L2 ◽  
The Impact ◽  
Flow Pump

A multi-region dynamic slip method was established to study the internal flow characteristics of the mixed-flow pump under the Alford effect. The ANSYS Fluent software and the standard k-ε two-equation model were used to numerically predict the mixed-flow pump’s external characteristics and analyze the forces on the impeller and guide vane internal vortex structure and non-uniform tip gap of the mixed-flow pump at different eccentric distances. The research results show that the external characteristic results of the numerical calculation are consistent with the experimental measurement. The head error of the design flow operating point is about 5%, and the efficiency error is no more than 3%, indicating the high accuracy of numerical calculation. Eccentricity has a significant influence on the flow field in the tip area of the mixed-flow pump impeller, the distribution of vortex core in the impeller presents obvious asymmetry, the strength and distribution area of the vortex core in the small gap area of the tip increase obviously, which aggravates the flow instability and increases the energy loss. With the increase of eccentricity, the strength and number of vortex core structures in the guide vane also increase significantly, and obvious flow separation occurs near the inlet of the guide vane suction surface on the eccentric side of the impeller. The circumferential distribution of L1 and L2 values represents the friction pressure gap in the eccentric state, and the eccentricity has a more noticeable effect on L1 and L2 values at the small gap; With the increase of eccentricity, the values of vorticity moment components L1 and L2 increase, and the Alford moment on the impeller increases. The leading-edge region of the blade is the main part affected by the unstable torque of the flow field. With the increase of eccentricity, the impact degree of tip leakage flow deepens, and the change of the tip surface pressure is the most obvious. The impact area of tip leakage flow is mainly concentrated in the first half of the impeller channel, which has an impact on the blade inlet flow field but has little impact on the blade outlet flow field.

On the Interactions of a Rotor Blade Tip Flow With Axial Casing Grooves in an Axial Compressor Near the Best Efficiency Point

2018 ◽  
Vol 141 (1) ◽  
Author(s):  
Huang Chen ◽  
Yuanchao Li ◽  
Joseph Katz
Keyword(s):  
Rotor Blade ◽  
Leading Edge ◽  
Secondary Flows ◽  
Maximum Efficiency ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Flow Angle ◽  
Tip Leakage ◽  
Blade Tip ◽  
The Impact

Experiments in a refractive index-matched axial turbomachine facility show that semicircular skewed axial casing grooves (ACGs) reduce the stall flowrate by 40% but cause a 2.4% decrease in the maximum efficiency. Aiming to elucidate mechanism that might cause the reduced efficiency, stereo-PIV measurements examine the impact of the ACGs on the flow structure and turbulence in the tip region near the best efficiency point (BEP), and compare them to those occurring without grooves and at low flowrates. Results show that the periodic inflow into the groove peaks when the rotor blade pressure side (PS) overlaps with the downstream end of the groove, but diminishes when this end faces the suction side (SS). Entrainment of the PS boundary layer and its vorticity generates a vortical loop at the entrance to the groove, and a “discontinuity” in the tip leakage vortex (TLV) trajectory. During exposure to the SS, the backward tip leakage flow separates at the entrance to the groove, generating a counter-rotating circumferential “corner vortex,” which the TLV entrains into the passage at high flowrates. Interactions among these structures enlarge the TLV and create a broad area with secondary flows and elevated turbulence near the groove's downstream corner. A growing shear layer with weaker turbulence also originates from the upstream corner. The groove also increases the flow angle upstream of the blade tip and varies it periodically. Accordingly, the circulation shed from the blade tip and strength of leakage flow increase near the blade leading edge (LE).

scholarly journals The Effect of Tip Leakage Flow on Part-Load Performance of a Mixed-Flow Pump Impeller

1991 ◽  
Author(s):  
Akira Goto
Keyword(s):  
Flow Characteristic ◽  
Pressure Head ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Mixed Flow ◽  
Pump Impeller ◽  
Abrupt Decrease ◽  
Tip Leakage ◽  
Extensive Flow ◽  
Flow Pump

The flow phenomena around the positive slope region of the head-flow characteristic were investigated experimentally on a mixed-flow pump impeller at various tip clearances for both shrouded and unshrouded cases. A positively-sloped head-flow characteristic (abrupt decrease in pressure head) was caused by the onset of extensive flow separation in the impeller at the casing-suction surface corner. The corner separation in unshrouded cases appeared at much lower flow rate than the shrouded case due to the favorable effect of the tip leakage flow which displaced the wake region away from the corner. The interaction between the tip leakage flows and secondary flows and the formation of the wake regions in shrouded and unshrouded cases were explained based on experimental observation and computations by the Dawes’ 3-D Navier-Stokes code. In the shrouded case, the flow rate, at which an abrupt decrease in pressure head appeared, was lowered substantially by introducing a leakage flow through a slit made between the shroud and the blade tip. Inlet recirculation was triggered by the corner separation and developed more gradually for larger tip clearances. Both the increased loss, due to the extensive flow separation, and the decreased Euler’s head, due to the abrupt change in flow pattern caused by the inlet recirculation, were responsible for the generation of positively-sloped head-flow characteristic in the unshrouded case when the tip clearance was small, while the increased loss was the primary factor in the shrouded case.

The Effect of Tip Leakage Flow on Part-Load Performance of a Mixed-Flow Pump Impeller

1992 ◽  
Vol 114 (2) ◽  
pp. 383-391 ◽  
Author(s):  
A. Goto
Keyword(s):  
Flow Characteristic ◽  
Pressure Head ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Mixed Flow ◽  
Pump Impeller ◽  
Abrupt Decrease ◽  
Tip Leakage ◽  
Extensive Flow ◽  
Flow Pump

The flow phenomena around the positive slope region of the head-flow characteristic were investigated experimentally on a mixed-flow pump impeller at various tip clearances for both shrouded and unshrouded cases. A positively sloped head-flow characteristic (abrupt decrease in pressure head) was caused by the onset of extensive flow separation in the impeller at the casing-suction surface corner. The corner separation in unshrouded cases appeared at a much lower flow rate than the shrouded case due to the favorable effect of the tip leakage flow, which displaced the wake region away from the corner. The interaction between the tip leakage flows and secondary flows and the formation of the wake regions in shrouded and unshrouded cases were explained based on experimental observation and computations by the Dawes three-dimensional Navier–Stokes code. In the shrouded case, the flow rate at which an abrupt decrease in pressure head appeared was lowered substantially by introducing a leakage flow through a slit made between the shroud and the blade tip. Inlet recirculation was triggered by the corner separation and developed more gradually for larger tip clearances. Both the increased loss, due to the extensive flow separation, and the decreased Euler’s head, due to the abrupt change in flow pattern caused by the inlet recirculation, were responsible for the generation of positively sloped head-flow characteristic in the unshrouded case when the tip clearance was small, while the increased loss was the primary factor in the shrouded case.

scholarly journals Effects of Tip Leakage Flow on the Aerodynamic Performance and Stability of an Axial-Flow Transonic Compressor Stage

Energies ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 4168
Author(s):  
Botao Zhang ◽  
Xiaochen Mao ◽  
Xiaoxiong Wu ◽  
Bo Liu
Keyword(s):  
Boundary Layer ◽  
Shock Wave ◽  
Axial Flow ◽  
Leading Edge ◽  
Rotating Stall ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Transonic Compressor

To explain the effect of tip leakage flow on the performance of an axial-flow transonic compressor, the compressors with different rotor tip clearances were studied numerically. The results show that as the rotor tip clearance increases, the leakage flow intensity is increased, the shock wave position is moved backward, and the interaction between the tip leakage vortex and shock wave is intensified, while that between the boundary layer and shock wave is weakened. Most of all, the stall mechanisms of the compressors with varying rotor tip clearances are different. The clearance leakage flow is the main cause of the rotating stall under large rotor tip clearance. However, the stall form for the compressor with half of the designed tip clearance is caused by the joint action of the rotor tip stall caused by the leakage flow spillage at the blade leading edge and the whole blade span stall caused by the separation of the boundary layer of the rotor and the stator passage. Within the investigated varied range, when the rotor tip clearance size is half of the design, the compressor performance is improved best, and the peak efficiency and stall margin are increased by 0.2% and 3.5%, respectively.

Study of the Standard k-ε Model for Tip Leakage Flow in an Axial Compressor Rotor

2016 ◽  
Vol 33 (4) ◽  
Author(s):  
Yanfei Gao ◽  
Yangwei Liu ◽  
Luyang Zhong ◽  
Jiexuan Hou ◽  
Lipeng Lu
Keyword(s):  
Flow Field ◽  
Large Scale ◽  
Turbulent Viscosity ◽  
Axial Compressor ◽  
Leakage Flow ◽  
Reynolds Stresses ◽  
Mean Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Compressor Rotor

AbstractThe standard k-ε model (SKE) and the Reynolds stress model (RSM) are employed to predict the tip leakage flow (TLF) in a low-speed large-scale axial compressor rotor. Then, a new research method is adopted to “freeze” the turbulent kinetic energy and dissipation rate of the flow field derived from the RSM, and obtain the turbulent viscosity using the Boussinesq hypothesis. The Reynolds stresses and mean flow field computed on the basis of the frozen viscosity are compared with the results of the SKE and the RSM. The flow field in the tip region based on the frozen viscosity is more similar to the results of the RSM than those of the SKE, although certain differences can be observed. This finding indicates that the non-equilibrium turbulence transport nature plays an important role in predicting the TLF, as well as the turbulence anisotropy.

Tip Leakage Flow Instability in a Centrifugal Compressor

2021 ◽  
Vol 143 (4) ◽  
Author(s):  
Teng Cao ◽  
Tadashi Kanzaka ◽  
Liping Xu ◽  
Tobias Brandvik
Keyword(s):  
Shear Layer ◽  
Centrifugal Compressor ◽  
Large Scale ◽  
Flow Instability ◽  
Leading Edge ◽  
Main Stream ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Unstable Flow ◽  
Tip Leakage

Abstract In this paper, an unsteady tip leakage flow phenomenon is identified and investigated in a centrifugal compressor with a vaneless diffuser at near-stall conditions. This phenomenon is associated with the inception of a rotating instability in the compressor. The study is based on numerical simulations that are supported by experimental measurements. The study confirms that the unstable flow is governed by a Kelvin–Helmholtz type instability of the shear layer formed between the main-stream flow and the tip leakage flow. The shear layer instability induces large-scale vortex roll-up and forms vortex tubes, which propagate circumferentially, resulting in measured pressure fluctuations with short wavelength and high amplitude which rotate at about half of the blade speed. The 3D vortex tube is also found to interact with the main blade leading edge, causing the reduction of the blade loading identified in the experiment. The paper also reveals that the downstream volute imposes a once-per-rev circumferential nonuniform back pressure at the impeller exit, inducing circumferential loading variation at the impeller inducer, and causing circumferential variation in the unsteady tip leakage flow.

scholarly journals Effect of Tip Clearance on Helico-Axial Flow Pump Performance at Off-Design Case

Processes ◽  
2021 ◽  
Vol 9 (9) ◽  
pp. 1653
Author(s):  
Nengqi Kan ◽  
Zongku Liu ◽  
Guangtai Shi ◽  
Xiaobing Liu
Keyword(s):  
Optimization Design ◽  
Flow Characteristics ◽  
Axial Flow ◽  
Leading Edge ◽  
Tip Clearance ◽  
Hydraulic Loss ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Axial Flow Pump ◽  
Flow Pump

To reveal the effect of tip clearance on the flow behaviors and pressurization performance of a helico-axial flow pump, the standard k-ε turbulence model is employed to simulate the flow characteristics in the self-developed helico-axial flow pump. The pressure, streamlines and turbulent kinetic energy in a helico-axial flow pump are analyzed. Results show that the tip leakage flow (TLF) forms a tip-separation vortex (TSV) when it enters the tip clearance and forms a tip-leakage vortex (TLV) when it leaves the tip clearance. As the blade tip clearance increases, the TLV moves along the blade from the leading edge (LE) to trailing edge (TE). At the same time, the entrainment between the TLV and the main flow deteriorates the flow pattern in the pump and causes great hydraulic loss. In addition, the existence of tip clearance also increases the possibility of TLV cavitation and has a great effect on the pressurization performance of the helico-axial flow pump. The research results provide the theoretical basis for the structural optimization design of the helico-axial flow pump.

Effect of Airfoil Vortex Generator on the Performance and Stability of a Transonic Axial Compressor

2021 ◽  
Author(s):  
Subbaramu Shivaramaiah ◽  
Mahesh K. Varpe
Keyword(s):  
Pressure Ratio ◽  
Research Work ◽  
Vortex Generator ◽  
Leading Edge ◽  
Leakage Flow ◽  
Compressor Stage ◽  
Tip Leakage Flow ◽  
Stall Margin ◽  
Tip Leakage ◽  
Transonic Compressor

Abstract In the present research work, effect of airfoil vortex generator on performance and stability of transonic compressor stage is investigated through CFD simulations. In turbomachines vortex generators are used to energize boundary and generated vortex is made to interact with tip leakage flow and secondary flow vortices formed in rotor and stator blade passage. In the present numerical investigation symmetrical airfoil vortex generator is placed on rotor casing surface close to leading edge, anticipating that vortex generated will be able to disturb tip leakage flow and its interaction with rotor passage core flow. Six different vortex generator configuration are investigated by varying distance between vortex generator trailing edge and rotor leading edge. Particular vortex generator configuration shows maximum improvement of stall margin and operating range by 5.5% and 76.75% respectively. Presence of vortex generator alters flow blockage by modifying flow field in rotor tip region and hence contributes to enhancement of stall margin. As a negative effect, interaction of vortex generator vortices and casing causes surface friction and high entropy generation. As a result compressor stage pressure ratio and efficiency decreases.

Sign in / Sign up

Export Citation Format

Share Document