Dynamic responses of elastic marine propellers in non-uniform flows

2021 ◽  
pp. 147509022110609
Author(s):  
Jiasheng Li ◽  
Yegao Qu ◽  
Yong Chen ◽  
Hongxing Hua ◽  
Junyun Wu
Keyword(s):  
Boundary Condition ◽  
Three Dimensional ◽  
Dynamic Responses ◽  
Blade Surface ◽  
The Finite Element Method ◽  
Strongly Coupled ◽  
Marine Propellers ◽  
Frequency Domains ◽  
Unsteady Performance ◽  
Normal Vectors

This paper focuses on the development of a three-dimensional panel method in time and frequency domains combined with the finite element method for analyzing the hydroelastic responses of rotating marine propellers in the wake of ships. A fully non-penetration boundary condition imposed on the deformed blade surface is conducted, in which the corrections of both the incoming flow velocities and the normal vectors imposed on the deformed and undeformed blade surface are taken into account. The added-mass and -damping matrices due to strongly coupled fluid-structure interaction are considered. Results of the present method are compared with experimental data available in the literature. It is observed that the fully non-penetration boundary condition applied on the deformed blade surface should be imposed to predict the unsteady performance of elastic propellers, which is due to the change of the added damping predicted by considering different non-penetration boundary conditions.

Forced vibration of a bi-axially pre-stressed plate subjected to a harmonic point force and resting on a rigid foundation

2019 ◽  
Vol 43 (3) ◽  
pp. 333-343
Author(s):  
Ahmet Daşdemir ◽  
Mustafa Eröz
Keyword(s):  
Finite Element Method ◽  
Forced Vibration ◽  
Elastic Waves ◽  
Three Dimensional ◽  
Dynamic Responses ◽  
Rigid Foundation ◽  
The Finite Element Method ◽  
System Parameters ◽  
Linearized Theory ◽  
Stress Influences

This paper models the harmonically forced vibration of a bi-axially pre-stressed plate resting on a rigid foundation using the three-dimensional linearized theory of elastic waves in initially stressed bodies. This model assumes that the material is linearly elastic, homogenous, and isotropic. The model of this system is numerically evaluated using the finite element method simulations. The numerical results illustrate the influence of several system parameters on the dynamic responses of the stresses acting at the interface between the plate and its rigid foundation. The simulations show that the aspect ratio of the plate determines how the initial stress influences the behavior of the system.

The Complete Three-Dimensional Calculation of the Compressible Flow Field in Turbo Impellers

1978 ◽  
Vol 20 (3) ◽  
pp. 149-158 ◽  
Author(s):  
Y. Krimerman ◽  
D. Adler
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Arbitrary Shape ◽  
Axisymmetric Flow ◽  
Three Dimensional ◽  
Blade Surface ◽  
The Finite Element Method ◽  
Mixed Flow ◽  
Flow Calculation ◽  
Corrected Flow

The calculation of the complete, three-dimensional, subsonic, non-viscous flow in turbo impellers of arbitrary shape (axial, radial or mixed flow) is presented. The finite-element method is used to solve modified subsonic Wu equations. The solution is carried out using four basic algorithms: ( a) axisymmetric flow calculation in the meridional surface, ( b) flow calculation on an axisymmetric blade-to-blade surface, ( c) non-axisymmetric corrected flow calculation on a meridional surface, and ( d) flow calculation on a non-axisymmetric blade-to-blade surface. These basic algorithms are combined into a calculation procedure in which algorithms a and b are used as the first two steps, and algorithms c and d are alternately used until convergence is achieved. Algorithms b, c and d are applied to a number of stream surfaces.

Macroorganisation and flexibility of thylakoid membranes

2019 ◽  
Vol 476 (20) ◽  
pp. 2981-3018 ◽  
Author(s):  
Petar H. Lambrev ◽  
Parveen Akhtar
Keyword(s):  
Light Harvesting ◽  
Current Knowledge ◽  
Three Dimensional ◽  
Photosynthetic Apparatus ◽  
Dynamic Responses ◽  
State Transitions ◽  
Photochemical Quenching ◽  
Light Harvesting Complex ◽  
Complex Ii ◽  
Light Harvesting Complex Ii

Abstract The light reactions of photosynthesis are hosted and regulated by the chloroplast thylakoid membrane (TM) — the central structural component of the photosynthetic apparatus of plants and algae. The two-dimensional and three-dimensional arrangement of the lipid–protein assemblies, aka macroorganisation, and its dynamic responses to the fluctuating physiological environment, aka flexibility, are the subject of this review. An emphasis is given on the information obtainable by spectroscopic approaches, especially circular dichroism (CD). We briefly summarise the current knowledge of the composition and three-dimensional architecture of the granal TMs in plants and the supramolecular organisation of Photosystem II and light-harvesting complex II therein. We next acquaint the non-specialist reader with the fundamentals of CD spectroscopy, recent advances such as anisotropic CD, and applications for studying the structure and macroorganisation of photosynthetic complexes and membranes. Special attention is given to the structural and functional flexibility of light-harvesting complex II in vitro as revealed by CD and fluorescence spectroscopy. We give an account of the dynamic changes in membrane macroorganisation associated with the light-adaptation of the photosynthetic apparatus and the regulation of the excitation energy flow by state transitions and non-photochemical quenching.

Comparison of Conventional and Pontic Fixed Partial Dentures Over Implants Using the Finite Element Method: Three-Dimensional Analysis of Cortical and Medullary Bone Stress

2020 ◽  
Vol 46 (3) ◽  
pp. 175-181
Author(s):  
Marcelo Bighetti Toniollo ◽  
Mikaelly dos Santos Sá ◽  
Fernanda Pereira Silva ◽  
Giselle Rodrigues Reis ◽  
Ana Paula Macedo ◽  
...  
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Three Dimensional ◽  
The Finite Element Method ◽  
Medullary Bone ◽  
Principal Stresses ◽  
Bone Stress ◽  
Bone Damage ◽  
Rehabilitation System ◽  
Minimum Requirements

Rehabilitation with implant prostheses in posterior areas requires the maximum number of possible implants due to the greater masticatory load of the region. However, the necessary minimum requirements are not always present in full. This project analyzed the minimum principal stresses (TMiP, representative of the compressive stress) to the friable structures, specifically the vestibular face of the cortical bone and the vestibular and internal/lingual face of the medullary bone. The experimental groups were as follows: the regular splinted group (GR), with a conventional infrastructure on 3 regular-length Morse taper implants (4 × 11 mm); and the regular pontic group (GP), with a pontic infrastructure on 2 regular-length Morse taper implants (4 × 11 mm). The results showed that the TMiP of the cortical and medullary bones were greater for the GP in regions surrounding the implants (especially in the cervical and apical areas of the same region) but they did not reach bone damage levels, at least under the loads applied in this study. It was concluded that greater stress observed in the GP demonstrates greater fragility with this modality of rehabilitation; this should draw the professional's attention to possible biomechanical implications. Whenever possible, professionals should give preference to use of a greater number of implants in the rehabilitation system, with a focus on preserving the supporting tissue with the generation of less intense stresses.

Towards Predicting Relative Belt Edge Endurance With the Finite Element Method

1990 ◽  
Vol 18 (4) ◽  
pp. 216-235 ◽  
Author(s):  
J. De Eskinazi ◽  
K. Ishihara ◽  
H. Volk ◽  
T. C. Warholic
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Three Dimensional ◽  
The Finite Element Method ◽  
Shear Deformations ◽  
Element Analysis ◽  
Vertical Loading ◽  
Predicted Values ◽  
Element Method

Abstract The paper describes the intention of the authors to determine whether it is possible to predict relative belt edge endurance for radial passenger car tires using the finite element method. Three groups of tires with different belt edge configurations were tested on a fleet test in an attempt to validate predictions from the finite element results. A two-dimensional, axisymmetric finite element analysis was first used to determine if the results from such an analysis, with emphasis on the shear deformations between the belts, could be used to predict a relative ranking for belt edge endurance. It is shown that such an analysis can lead to erroneous conclusions. A three-dimensional analysis in which tires are modeled under free rotation and static vertical loading was performed next. This approach resulted in an improvement in the quality of the correlations. The differences in the predicted values of various stress analysis parameters for the three belt edge configurations are studied and their implication on predicting belt edge endurance is discussed.

Boundary Condition Design to Heat a Moving Object at Uniform Transient Temperature Using Inverse Formulation

2004 ◽  
Vol 126 (3) ◽  
pp. 619-626 ◽  
Author(s):  
Hakan Ertu¨rk ◽  
Ofodike A. Ezekoye ◽  
John R. Howell
Keyword(s):  
Boundary Condition ◽  
Temperature Distribution ◽  
Design Problem ◽  
Manufacturing Industry ◽  
Three Dimensional ◽  
Chemical Deposition ◽  
Iterative Solution ◽  
Conveyor Belt ◽  
Temperature History ◽  
Transient Temperature

The boundary condition design of a three-dimensional furnace that heats an object moving along a conveyor belt of an assembly line is considered. A furnace of this type can be used by the manufacturing industry for applications such as industrial baking, curing of paint, annealing or manufacturing through chemical deposition. The object that is to be heated moves along the furnace as it is heated following a specified temperature history. The spatial temperature distribution on the object is kept isothermal through the whole process. The temperature distribution of the heaters of the furnace should be changed as the object moves so that the specified temperature history can be satisfied. The design problem is transient where a series of inverse problems are solved. The process furnace considered is in the shape of a rectangular tunnel where the heaters are located on the top and the design object moves along the bottom. The inverse design approach is used for the solution, which is advantageous over a traditional trial-and-error solution where an iterative solution is required for every position as the object moves. The inverse formulation of the design problem is ill-posed and involves a set of Fredholm equations of the first kind. The use of advanced solvers that are able to regularize the resulting system is essential. These include the conjugate gradient method, the truncated singular value decomposition or Tikhonov regularization, rather than an ordinary solver, like Gauss-Seidel or Gauss elimination.

scholarly journals Vibration characteristics of triple-gear-rotor system in compressed air energy storage under variable torque load

2021 ◽  
Vol 104 (1) ◽  
pp. 003685042098705
Author(s):  
Xinran Wang ◽  
Yangli Zhu ◽  
Wen Li ◽  
Dongxu Hu ◽  
Xuehui Zhang ◽  
...  
Keyword(s):  
Large Scale ◽  
Three Dimensional ◽  
Element Model ◽  
Rotor System ◽  
Dynamic Responses ◽  
System Response ◽  
Rotating Speed ◽  
Torque Load ◽  
Set Up ◽  
Two Stages

This paper focuses on the effects of the off-design operation of CAES on the dynamic characteristics of the triple-gear-rotor system. A finite element model of the system is set up with unbalanced excitations, torque load excitations, and backlash which lead to variations of tooth contact status. An experiment is carried out to verify the accuracy of the mathematical model. The results show that when the system is subjected to large-scale torque load lifting at a high rotating speed, it has two stages of relatively strong periodicity when the torque load is light, and of chaotic when the torque load is heavy, with the transition between the two states being relatively quick and violent. The analysis of the three-dimensional acceleration spectrum and the meshing force shows that the variation in the meshing state and the fluctuation of the meshing force is the basic reasons for the variation in the system response with the torque load. In addition, the three rotors in the triple-gear-rotor system studied show a strong similarity in the meshing states and meshing force fluctuations, which result in the similarity in the dynamic responses of the three rotors.

scholarly journals Bootstrapping boundary-localized interactions

2020 ◽  
Vol 2020 (12) ◽  
Author(s):  
Connor Behan ◽  
Lorenzo Di Pietro ◽  
Edoardo Lauria ◽  
Balt C. van Rees
Keyword(s):  
Boundary Condition ◽  
Scalar Field ◽  
Boundary Conditions ◽  
Parameter Space ◽  
Three Dimensional ◽  
Conformal Boundary ◽  
Dimensional Boundary ◽  
Dirichlet And Neumann Conditions ◽  
Boundary Fields ◽  
Boundary Dynamics

Abstract We study conformal boundary conditions for the theory of a single real scalar to investigate whether the known Dirichlet and Neumann conditions are the only possibilities. For this free bulk theory there are strong restrictions on the possible boundary dynamics. In particular, we find that the bulk-to-boundary operator expansion of the bulk field involves at most a ‘shadow pair’ of boundary fields, irrespective of the conformal boundary condition. We numerically analyze the four-point crossing equations for this shadow pair in the case of a three-dimensional boundary (so a four-dimensional scalar field) and find that large ranges of parameter space are excluded. However a ‘kink’ in the numerical bounds obeys all our consistency checks and might be an indication of a new conformal boundary condition.

scholarly journals The effect of the outlet angle β2 on the thermomechanical behavior of a centrifugal compressor blade

2020 ◽  
Vol 29 (1) ◽  
pp. 1-8
Author(s):  
Ahmed Allali ◽  
Sadia Belbachir ◽  
Ahmed Alami ◽  
Belhadj Boucham ◽  
Abdelkader Lousdad
Keyword(s):  
Mechanical Behavior ◽  
Centrifugal Compressor ◽  
Three Dimensional ◽  
Complex Form ◽  
Compressor Blade ◽  
Stress Fields ◽  
The Finite Element Method ◽  
Mechanical Fatigue ◽  
Outlet Angle ◽  
The Impact

AbstractThe objective of this work lies in the three-dimensional study of the thermo mechanical behavior of a blade of a centrifugal compressor. Numerical modeling is performed on the computational code "ABAQUS" based on the finite element method. The aim is to study the impact of the change of types of blades, which are defined as a function of wheel output angle β2, on the stress fields and displacements coupled with the variation of the temperature.This coupling defines in a realistic way the thermo mechanical behavior of the blade where one can note the important concentrations of stresses and displacements in the different zones of its complex form as well as the effects at the edges. It will then be possible to prevent damage and cracks in the blades of the centrifugal compressor leading to its failure which can be caused by the thermal or mechanical fatigue of the material with which the wheel is manufactured.

Sign in / Sign up

Export Citation Format

Share Document