Mixed convection from a discrete heater in lid-driven enclosures filled with non-Newtonian nanofluids

2016 ◽  
Vol 231 (1) ◽  
pp. 3-16 ◽  
Author(s):  
AM Rashad ◽  
MA Mansour ◽  
Rama Subba Reddy Gorla
Keyword(s):  
Nusselt Number ◽  
Heat Source ◽  
Local Nusselt Number ◽  
Volume Fraction ◽  
Fluid Model ◽  
Convection Flow ◽  
Viscosity Parameter ◽  
Volumetric Rate ◽  
Vertical Walls ◽  
Volume Method

The transport mechanism of laminar combined convection flow of an incompressible viscous non-Newtonian nanofluid in a shear- and buoyancy-driven enclosure has been investigated in this article. The micropolar fluid model is used for the rheological behavior of the non-Newtonian fluid. A heat source with constant volumetric rate is attached in a part of the bottom wall and the remaining parts are thermally insulated. The vertical walls of the cavity are considered to be adiabatic, while the top wall is cooled and moves from left to right with uniform velocity. The thermal conductivity and the dynamic viscosity of the nanofluid are represented by different experimental correlations that are suitable to each nanoparticles. The finite volume method is applied to solve the dimensionless form of the governing equations. A discussion is provided for the effects of the governing parameters on the local Nusselt number and average Nusselt number along the heat source. It is found that an increase in the vortex-viscosity parameter causes a reduction in the local Nusselt number. As the vortex-viscosity parameter increases by 10 times from 0.5 to 5, the Nusselt number reduces by 15%. Additionally, as the nanoparticle volume fraction increases, the rate of heat transfer increases. As the volume fraction increases by 100% from 0.1 to 0.2, the Nusselt number increases by 86%.

Impact of Partial Slip on Magneto-Ferrofluids Mixed Convection Flow in Enclosure

2020 ◽  
Vol 12 (5) ◽  
Author(s):  
Ali J. Chamkha ◽  
A. M. Rashad ◽  
A. I. Alsabery ◽  
Z. M. A. Abdelrahman ◽  
Hossam A. Nabwey
Keyword(s):  
Heat Source ◽  
Mixed Convection ◽  
Volume Fraction ◽  
Partial Slip ◽  
Convection Flow ◽  
Mixed Convection Flow ◽  
Square Enclosure ◽  
Vertical Walls ◽  
Volume Method ◽  
Ferromagnetic Particles

Abstract Magneto-ferrofluid mixed convection flow inside a lid-driven square cavity with partial slip is investigated numerically using the finite volume method. The vertical walls of the enclosure are heated partially by a constant temperature, while the horizontal moving walls are kept adiabatic. The square enclosure is filled with a mixture of kerosene–cobalt ferrofluids. The numerical computations are obtained for various parameters of the heat source length, position of the heat source, Hartmann number, Richardson number, fraction ferromagnetic particles, and constant movement parameter. It is shown that the transfer rate is clearly affected by the augmentation of the ferromagnetic particles volume fraction under the influence of a relative magnetic field and by the opposite-direction horizontal walls movement.

Effect of Nanofluid on Heat Transfer Enhancement for Mixed Convection Flow Over a Corrugated Surface

2020 ◽  
Vol 45 (4) ◽  
pp. 373-383
Author(s):  
Nepal Chandra Roy ◽  
Sadia Siddiqa
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Nusselt Number ◽  
Mixed Convection ◽  
Local Nusselt Number ◽  
Richardson Number ◽  
Thermal Boundary Layer ◽  
Volume Fraction ◽  
Convection Flow ◽  
Mixed Convection Flow

AbstractA mathematical model for mixed convection flow of a nanofluid along a vertical wavy surface has been studied. Numerical results reveal the effects of the volume fraction of nanoparticles, the axial distribution, the Richardson number, and the amplitude/wavelength ratio on the heat transfer of Al2O3-water nanofluid. By increasing the volume fraction of nanoparticles, the local Nusselt number and the thermal boundary layer increases significantly. In case of \mathrm{Ri}=1.0, the inclusion of 2 % and 5 % nanoparticles in the pure fluid augments the local Nusselt number, measured at the axial position 6.0, by 6.6 % and 16.3 % for a flat plate and by 5.9 % and 14.5 %, and 5.4 % and 13.3 % for the wavy surfaces with an amplitude/wavelength ratio of 0.1 and 0.2, respectively. However, when the Richardson number is increased, the local Nusselt number is found to increase but the thermal boundary layer decreases. For small values of the amplitude/wavelength ratio, the two harmonics pattern of the energy field cannot be detected by the local Nusselt number curve, however the isotherms clearly demonstrate this characteristic. The pressure leads to the first harmonic, and the buoyancy, diffusion, and inertia forces produce the second harmonic.

scholarly journals Three-Dimensional MHD Mixed Convection Flow of Casson Nanofluid with Hall and Ion Slip Effects

2020 ◽  
Vol 2020 ◽  
pp. 1-15
Author(s):  
Wubshet Ibrahim ◽  
Temesgen Anbessa
Keyword(s):  
Nusselt Number ◽  
Heat Source ◽  
Mixed Convection ◽  
Skin Friction ◽  
Local Nusselt Number ◽  
Three Dimensional ◽  
Casson Fluid ◽  
Convection Flow ◽  
Mixed Convection Flow ◽  
Ion Slip

The intention of the present study is to scrutinize the three-dimensional MHD mixed convection flow of Casson nanofluid over an exponentially stretching sheet using the impacts of Hall and ion slip currents. Moreover, the impacts of thermal radiation and heat source are considered in this study. The governing partial differential equations are transformed into a system of joined nonlinear ordinary differential equations using similarity transformations, and they are solved numerically employing a spectral relaxation method (SRM). The obtained results are contrasted with existing specific cases, and a reasonable harmony is established. The impacts of noteworthy physical parameters on the velocities, thermal and concentration distributions, skin friction coefficients, local Nusselt number, and local Sherwood number are investigated graphically. It is found that the rise in Casson fluid and magnetic field parameters reduce the velocity profiles along both x− and y− directions while the reverse tendency is observed with an increment in Hall, ion slip, and mixed convection parameters. Moreover, the increase in both radiation and heat source parameters enhances the temperature profile. It is also observed that both the skin friction coefficients reduced with an increase in Casson fluid, Hall, and ion slip parameters. Furthermore, the local Nusselt number enhances with an augment in radiation parameter, whereas the opposite trends of local Nusselt and Sherwood numbers are found with an increase in heat source parameter.

scholarly journals Study of convection heat transfer enhancement inside lid driven cavity utilizing fins and nanofluid

2017 ◽  
Vol 21 (6 Part A) ◽  
pp. 2431-2442
Author(s):  
Arash Lavasani ◽  
Mousa Farhadi ◽  
Darzi Rabienataj
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Richardson Number ◽  
Volume Fraction ◽  
Convection Heat Transfer ◽  
Thermal Conductivity Ratio ◽  
Convection Flow ◽  
Driven Cavity ◽  
Ratio Change ◽  
Hot Surface

In the present study, the effect of suspension of nanoparticle on mixed convection flow is investigated numerically in lid driven cavity with fins on its hot surface. Study is carried out for Richardson numbers ranging from 0.1 to 10, fin(s) height ratio change from 0.05 to 0.15 and volume fraction of nanoparticles from 0 to 0.03, respectively. The thermal conductivity ratio (kfin/kf) is equal to 330 and Grashof number is assumed to be constant (104) so that the Richardson numbers changes with Reynolds number. Results show that the heat transfer enhances by using nanofluid for all studied Richardson numbers. Adding fins on hot wall has different effects on heat transfer depend to Richardson number and height of fins. Use of low height fin in flow with high Richardson number enhances the heat transfer rate while by increasing the height of fin the heat transfer reduces even lower than it for pure fluid. The overall enhancement in Nusselt number by adding 3% nanoparticles and 3 fins is 54% at Ri=10. They cause reduction of Nusselt Number by 25% at Ri=0.1. Higher fins decrease the heat transfer due to blocking fluid at corners of fins.

scholarly journals Analysis of transient mixed convection in a horizontal channel partially heated from below

2021 ◽  
Vol 4 (8(112)) ◽  
pp. 16-22
Author(s):  
Mahmoud A. Mashkour
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Heat Source ◽  
Local Nusselt Number ◽  
Richardson Number ◽  
Stokes Equations ◽  
Heat Convection ◽  
Horizontal Channel ◽  
Outlet Temperature

The heat convection phenomenon has been investigated numerically (mathematically) for a channel located horizontally and partially heated at a uniform heat flux with forced and free heat convection. The investigated horizontal channel with a fluid inlet and the enclosure was exposed to the heat source from the bottom while the channel upper side was kept with a constant temperature equal to fluid outlet temperature. Transient, laminar, incompressible and mixed convective flow is assumed within the channel. Therefore, the flow field is estimated using Navier Stokes equations, which involves the Boussinesq approximation. While the temperature field is calculated using the standard energy model, where, Re, Pr, Ri are Reynolds number, Prandtl number, and Richardson number, respectively. Reynolds number (Re) was changed during the test from 1 to 50 (1, 10, 25, and 50) for each case study, Richardson (Ri) number was changed during the test from 1 to 25 (1, 5, 10, 15, 20, and, 25). The average Nusselt number (Nuav) increases exponentially with the Reynold number for each Richardson number and the local Nusselt number (NuI) rises in the heating point. Then gradually stabilized until reaching the endpoint of the channel while the local Nusselt number increases with a decrease in the Reynolds number over there. In addition, the streamlines and isotherms patterns in case of the very low value of the Reynolds number indicate very low convective heat transfer with all values of Richardson number. Furthermore, near the heat source, the fluid flow rate rise increases the convection heat transfer that clarified the Nusselt number behavior with Reynolds number indicating that maximum Nu No. are 6, 12, 27 and 31 for Re No. 1, 10, 25 and 50, respectively

scholarly journals Mixed convection of functionalized DWCNT-water nanofluid in baffled lid-driven cavities

2018 ◽  
Vol 22 (6 Part A) ◽  
pp. 2503-2514 ◽  
Author(s):  
Esfe Hemmat ◽  
Arani Abbasian ◽  
Wei-Mon Yan ◽  
Alireza Aghaie ◽  
Masoud Afrand ◽  
...  
Keyword(s):  
Nusselt Number ◽  
Mixed Convection ◽  
Richardson Number ◽  
Average Nusselt Number ◽  
Volume Fraction ◽  
Minimum Length ◽  
Convection Flow ◽  
Flow And Heat Transfer ◽  
Inclination Angles ◽  
Nanoparticles Volume Fraction

The present study aims to evaluate the mixed convection flow and heat transfer of functionalized DWCNT/water nanofluids with variable properties in a cavity having hot baffles. The investigation is performed at different nanoparticles volume fraction including 0, 0.0002, 0.001, 0.002, and 0.004, Richardson numbers ranging from 0.01 to 100, inclination angles ranging from 0 to 60? and at constant Grashof number of 104. The results presented as streamlines and isotherms plot and Nusselt number diagrams. According to the finding with increasing nanoparticles volume fraction and distance between the left hot baffles of nanoparticles average Nusselt number enhances for all considered Richardson numbers and cavity inclination angles. Also with increasing Richardson number, the rate of changes of average Nusselt number increase with increasing distance between the left hot baffles. For example, at Richardson number of 0.01, by increasing L1 from 0.4 to 0.6, the average Nusselt number increases 7%; while for similar situation at Richardson number of 0.1, 1.0, and 10, the average Nusselt number increases, respectively, 17%, 24%, and 26%. At all Richardson numbers, the maximum value of average Nusselt number is achieved for a minimum length of left baffles. <br><br><font color="red"><b> This article has been corrected. Link to the correction <u><a href="http://dx.doi.org/10.2298/TSCI190203032E">10.2298/TSCI190203032E</a><u></b></font>

scholarly journals Numerical Investigation of Mixed Convection and Entropy Generation in a Wavy-Walled Cavity Filled with Nanofluid and Involving a Rotating Cylinder

Entropy ◽  
2018 ◽  
Vol 20 (9) ◽  
pp. 664 ◽  
Author(s):  
Ammar Alsabery ◽  
Muneer Ismael ◽  
Ali Chamkha ◽  
Ishak Hashim
Keyword(s):  
Heat Exchange ◽  
Rayleigh Number ◽  
Heat Source ◽  
Mixed Convection ◽  
Volume Fraction ◽  
Numerical Study ◽  
Rotational Velocity ◽  
Geometrical Parameters ◽  
Galerkin Finite Element ◽  
Vertical Walls

This numerical study considers the mixed convection and the inherent entropy generated in Al 2 O 3 –water nanofluid filling a cavity containing a rotating conductive cylinder. The vertical walls of the cavity are wavy and are cooled isothermally. The horizontal walls are thermally insulated, except for a heat source segment located at the bottom wall. The dimensionless governing equations subject to the selected boundary conditions are solved numerically using the Galerkin finite-element method. The study is accomplished by inspecting different ranges of the physical and geometrical parameters, namely, the Rayleigh number ( 10 3 ≤ R a ≤ 10 6 ), angular rotational velocity ( 0 ≤ Ω ≤ 750 ), number of undulations ( 0 ≤ N ≤ 4 ), volume fraction of Al 2 O 3 nanoparticles ( 0 ≤ ϕ ≤ 0.04 ), and the length of the heat source ( 0.2 ≤ H ≤ 0.8 ) . The results show that the rotation of the cylinder boosts the rate of heat exchange when the Rayleigh number is less than 5 × 10 5 . The number of undulations affects the average Nusselt number for a still cylinder. The rate of heat exchange increases with the volume fraction of the Al 2 O 3 nanoparticles and the length of the heater segment.

scholarly journals Mixed Convection and Entropy Generation of an Ag-Water Nanofluid in an Inclined L-Shaped Channel

Energies ◽  
2019 ◽  
Vol 12 (6) ◽  
pp. 1150 ◽  
Author(s):  
Taher Armaghani ◽  
Muneer Ismael ◽  
Ali Chamkha ◽  
Ioan Pop
Keyword(s):  
Nusselt Number ◽  
Mixed Convection ◽  
Entropy Generation ◽  
Richardson Number ◽  
Volume Fraction ◽  
Governing Equations ◽  
Nanoparticles Volume Fraction ◽  
The Mean ◽  
The Right ◽  
Volume Method

This paper investigates the mixed convection and entropy generation of an Ag-water nanofluid in an L-shaped channel fixed at an inclination angle of 30° to the horizontal axis. An isothermal heat source was positioned in the middle of the right inclined wall of the channel while the other walls were kept adiabatic. The finite volume method was used for solving the problem’s governing equations. The numerical results were obtained for a range of pertinent parameters: Reynolds number, Richardson number, aspect ratio, and the nanoparticles volume fraction. These results were Re = 50–200; Ri = 0.1, 1, 10; AR = 0.5–0.8; and φ = 0.0–0.06, respectively. The results showed that both the Reynolds and the Richardson numbers enhanced the mean Nusselt number and minimized the rate of entropy generation. It was also found that when AR. increased, the mean Nusselt number was enhanced, and the rate of entropy generation decreased. The nanoparticles volume fraction was predicted to contribute to increasing both the mean Nusselt number and the rate of entropy generation.

Free Convection Flow of a Nanofluid Past an Isothermal Inclined Plate

2013 ◽  
Vol 390 ◽  
pp. 129-133 ◽  
Author(s):  
Marneni Narahari ◽  
S. Akilu ◽  
A. Jaafar
Keyword(s):  
Nusselt Number ◽  
Brownian Motion ◽  
Volume Fraction ◽  
Convection Flow ◽  
Inclined Plate ◽  
Convective Boundary ◽  
Linear Ordinary Differential Equations ◽  
Keller Box Method ◽  
Brownian Motion And Thermophoresis ◽  
Layer Flow

In this paper, the natural convective boundary-layer flow of a nanofluid over an isothermal inclined plate is investigated numerically with the effects of Brownian motion and thermophoresis in the nanofluid model. The equations governing the flow are expressed in the form of coupled non-linear ordinary differential equations using the similarity analysis. These equations are then solved numerically by an implicit finite-difference method known as the Keller-box method. The effect of inclination angle on the dimensionless velocity, temperature, nanofluid volume fraction and Nusselt number has been analyzed through graphs. Brownian motion and thermophoresis effects on the Nusselt number at an inclined plate are also discussed.

scholarly journals Effects of Slip and Heat Generation/Absorption on MHD Mixed Convection Flow of a Micropolar Fluid over a Heated Stretching Surface

2010 ◽  
Vol 2010 ◽  
pp. 1-20 ◽  
Author(s):  
Mostafa Mahmoud ◽  
Shimaa Waheed
Keyword(s):  
Nusselt Number ◽  
Friction Coefficient ◽  
Mixed Convection ◽  
Skin Friction ◽  
Heat Generation ◽  
Local Nusselt Number ◽  
Skin Friction Coefficient ◽  
Convection Flow ◽  
Local Skin ◽  
Local Skin Friction

A theoretical analysis is performed to study the flow and heat transfer characteristics of magnetohydrodynamic mixed convection flow of a micropolar fluid past a stretching surface with slip velocity at the surface and heat generation (absorption). The transformed equations solved numerically using the Chebyshev spectral method. Numerical results for the velocity, the angular velocity, and the temperature for various values of different parameters are illustrated graphically. Also, the effects of various parameters on the local skin-friction coefficient and the local Nusselt number are given in tabular form and discussed. The results show that the mixed convection parameter has the effect of enhancing both the velocity and the local Nusselt number and suppressing both the local skin-friction coefficient and the temperature. It is found that local skin-friction coefficient increases while the local Nusselt number decreases as the magnetic parameter increases. The results show also that increasing the heat generation parameter leads to a rise in both the velocity and the temperature and a fall in the local skin-friction coefficient and the local Nusselt number. Furthermore, it is shown that the local skin-friction coefficient and the local Nusselt number decrease when the slip parameter increases.

Sign in / Sign up

Export Citation Format

Share Document