scholarly journals Analysis of transient mixed convection in a horizontal channel partially heated from below

2021 ◽  
Vol 4 (8(112)) ◽  
pp. 16-22
Author(s):  
Mahmoud A. Mashkour
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Heat Source ◽  
Local Nusselt Number ◽  
Richardson Number ◽  
Stokes Equations ◽  
Heat Convection ◽  
Horizontal Channel ◽  
Outlet Temperature

The heat convection phenomenon has been investigated numerically (mathematically) for a channel located horizontally and partially heated at a uniform heat flux with forced and free heat convection. The investigated horizontal channel with a fluid inlet and the enclosure was exposed to the heat source from the bottom while the channel upper side was kept with a constant temperature equal to fluid outlet temperature. Transient, laminar, incompressible and mixed convective flow is assumed within the channel. Therefore, the flow field is estimated using Navier Stokes equations, which involves the Boussinesq approximation. While the temperature field is calculated using the standard energy model, where, Re, Pr, Ri are Reynolds number, Prandtl number, and Richardson number, respectively. Reynolds number (Re) was changed during the test from 1 to 50 (1, 10, 25, and 50) for each case study, Richardson (Ri) number was changed during the test from 1 to 25 (1, 5, 10, 15, 20, and, 25). The average Nusselt number (Nuav) increases exponentially with the Reynold number for each Richardson number and the local Nusselt number (NuI) rises in the heating point. Then gradually stabilized until reaching the endpoint of the channel while the local Nusselt number increases with a decrease in the Reynolds number over there. In addition, the streamlines and isotherms patterns in case of the very low value of the Reynolds number indicate very low convective heat transfer with all values of Richardson number. Furthermore, near the heat source, the fluid flow rate rise increases the convection heat transfer that clarified the Nusselt number behavior with Reynolds number indicating that maximum Nu No. are 6, 12, 27 and 31 for Re No. 1, 10, 25 and 50, respectively

Effect of Nanofluid on Heat Transfer Enhancement for Mixed Convection Flow Over a Corrugated Surface

2020 ◽  
Vol 45 (4) ◽  
pp. 373-383
Author(s):  
Nepal Chandra Roy ◽  
Sadia Siddiqa
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Nusselt Number ◽  
Mixed Convection ◽  
Local Nusselt Number ◽  
Richardson Number ◽  
Thermal Boundary Layer ◽  
Volume Fraction ◽  
Convection Flow ◽  
Mixed Convection Flow

AbstractA mathematical model for mixed convection flow of a nanofluid along a vertical wavy surface has been studied. Numerical results reveal the effects of the volume fraction of nanoparticles, the axial distribution, the Richardson number, and the amplitude/wavelength ratio on the heat transfer of Al2O3-water nanofluid. By increasing the volume fraction of nanoparticles, the local Nusselt number and the thermal boundary layer increases significantly. In case of \mathrm{Ri}=1.0, the inclusion of 2 % and 5 % nanoparticles in the pure fluid augments the local Nusselt number, measured at the axial position 6.0, by 6.6 % and 16.3 % for a flat plate and by 5.9 % and 14.5 %, and 5.4 % and 13.3 % for the wavy surfaces with an amplitude/wavelength ratio of 0.1 and 0.2, respectively. However, when the Richardson number is increased, the local Nusselt number is found to increase but the thermal boundary layer decreases. For small values of the amplitude/wavelength ratio, the two harmonics pattern of the energy field cannot be detected by the local Nusselt number curve, however the isotherms clearly demonstrate this characteristic. The pressure leads to the first harmonic, and the buoyancy, diffusion, and inertia forces produce the second harmonic.

Local Single-Phase Heat Transfer Research of Natural Circulation in Narrow Rectangular Channel

2017 ◽  
Author(s):  
Zhiqiang Zhu ◽  
Xiaxin Cao ◽  
Changqi Yan ◽  
Chunping Tian
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Inclination Angle ◽  
Local Nusselt Number ◽  
Single Phase ◽  
Natural Circulation ◽  
Rectangular Channel ◽  
Inlet Temperature

In order to explore and analyze the heat transfer characteristics in narrow rectangular channel, experiments on local single-phase heat transfer of natural circulation in a one-side heating narrow rectangular channel have been conducted under vertical and inclined condition. The thermotechnical parameters such as inlet temperature, heat flux and inclination angle varies during the experiments. The width of the flow channel is 40 mm and the narrow gap is 2 mm. It is heated from one side with a homogeneous and constant heat flux and the working medium is deionized water. Based on the experimental results, under vertical condition, the driving force in the loop goes up and the Reynolds number also increases when the inlet temperature is elevated, which causes an increase in local Nusselt number. When the heat flux rises, the local Nusselt number increases and the heat transfer temperature difference increases. The local Nusselts number is influenced by entrance effect and the entrance region length is computed for laminar and turbulent flow. Under inclined condition, with the inclination angle from −30° to 30°, it is found that when the inclination angle is positive, the local Nusselt number in fully developed region is larger than that under vertical condition and increases with the angle value, even though the Reynolds number decreases by the effect of incline. This phenomenon is explained by giving an analysis of the natural convection, which is characterized by the normal Grashof number, in the direction perpendicular to the heating plat. Moreover, the variation of heat transfer is also interpreted on the basis of field coordination principle. However, when the inclination angle is negative, the heat transfer shows no obvious difference between vertical condition and inclined condition.

scholarly journals Augmented of turbulent heat transfer in an annular pipe with abrupt expansion

2016 ◽  
Vol 20 (5) ◽  
pp. 1621-1632 ◽  
Author(s):  
Hussein Togun ◽  
Tuqa Abdulrazzaq ◽  
Salim Kazi ◽  
Ahmad Badarudin
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Surface Temperature ◽  
Local Nusselt Number ◽  
Expansion Ratio ◽  
Sudden Expansion ◽  
Inner Diameter ◽  
Annular Pipe

This paper presents a study of heat transfer to turbulent air flow in the abrupt axisymmetric expansion of an annular pipe. The experimental investigations were performed in the Reynolds number range from 5000 to 30000, the heat flux varied from 1000 to 4000 W/m2, and the expansion ratio was maintained at D/d=1, 1.25, 1.67 and 2. The sudden expansion was created by changing the inner diameter of the entrance pipe to an annular passage. The outer diameter of the inner pipe and the inner diameter of the outer pipe are 2.5 and 10 cm, respectively, where both of the pipes are subjected to uniform heat flux. The distribution of the surface temperature of the test pipe and the local Nusselt number are presented in this investigation. Due to sudden expansion in the cross section of the annular pipe, a separation flow was created, which enhanced the heat transfer. The reduction of the surface temperature on the outer and inner pipes increased with the increase of the expansion ratio and the Reynolds number, and increased with the decrease of the heat flux to the annular pipe. The peak of the local Nusselt number was between 1.64 and 1.7 of the outer and inner pipes for Reynolds numbers varied from 5000 to 30000, and the increase of the local Nusselt number represented the augmentation of the heat transfer rate in the sudden expansion of the annular pipe. This research also showed a maximum heat transfer enhancement of 63-78% for the outer and inner pipes at an expansion ratio of D/d=2 at a Re=30000 and a heat flux of 4000W/m2.

scholarly journals Thermal Performance Enhancement of the Mixed Convection between two Parallel Plates by using Triangular Ribs

2021 ◽  
Vol 26 (2) ◽  
pp. 11-30
Author(s):  
K.A. Jehhef ◽  
F.A. Badawy ◽  
A.A. Hussein
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Mixed Convection ◽  
Performance Enhancement ◽  
Stokes Equations ◽  
Channel Width ◽  
Heated Wall ◽  
Channel Height ◽  
Parallel Plates

Abstract This paper aims to investigate the mixed convection between two parallel plates of a vertical channel, in the presence of a triangular rib. The non-stationary Navier-Stokes equations were solved numerically in a two-dimensional formulation for the low Reynolds number for the laminar air flow regime. Six triangular ribs heat-generating elements were located equidistantly on the heated wall. The ratio of the ribs to the channel width is varied (h / H = 0.1, 0.2, 0.3 and 0.4) to study the effect of ribs height effects, the ratio of the channel width to the ribs height is fixed constant at (H / w = 2) and the ratio of the channel height to the ribs pitch is fixed at (W/p=10). The influence of the Reynolds number that ranged from 68 to 340 and the Grashof number that ranged from 6.6 ×103 to 2.6 ×104 as well as the Richardson number chosen (1.4, 0.7, 0.4 and 0.2) is studied. The numerical results are summarized and presented as the profile of the Nusselt number, the coefficient of friction, and the thermal enhancement factor. The contribution of forced and free convection to the total heat transfer is analyzed. Similar and distinctive features of the behavior of the local and averaged heat transfer with the variation of thermal gas dynamic and geometric parameters are investigated in this paper. The results showed that the Nusselt number and friction factor increased by using the attached triangular ribs, especially when using the downstream ribs. Also, the results revealed that the Nusselt number increased by increasing the ratio of the ribs to the channel width.

scholarly journals Numerical analysis of mixed convection in pulsating flow for a horizontal channel with a cavity heated from below

2016 ◽  
Vol 20 (1) ◽  
pp. 35-44 ◽  
Author(s):  
Fatih Selimefendigil
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Mixed Convection ◽  
Richardson Number ◽  
Amplitude Ratio ◽  
Pulsating Flow ◽  
Pulsation Frequency ◽  
Transfer Enhancement ◽  
Velocity Amplitude

In this study, a channel with a cavity heated from below is numerically investigated for the mixed convection case in pulsating flow for a range of Richardson numbers (Ri=0.1, 1, 10, 100) at Reynolds number of 50 in the laminar flow regime. At the inlet of the channel, pulsating velocity is imposed for Strouhal numbers between 0.1 to 1 and velocity amplitude ratio between 0.3 to 0.9. The effect of the pulsation frequency, amplitude and Richardson number on the heat transfer enhancement is numerically analyzed. The results are presented in terms of streamlines, isotherm plots and averaged Nusselt number plots. FFT plots for the Nusselt number response to single sinusoidal velocity forcing at the inlet and nonlinearity in the response is also provided.

Effects of moving wall on the flow of micropolar fluid inside a right angle triangular cavity

2018 ◽  
Vol 28 (10) ◽  
pp. 2404-2422 ◽  
Author(s):  
Mubbashar Nazeer ◽  
N. Ali ◽  
T. Javed
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Prandtl Number ◽  
Micropolar Fluid ◽  
Richardson Number ◽  
Average Nusselt Number ◽  
Content Type ◽  
Moving Wall ◽  
Flow And Heat Transfer

Purpose The main purpose of this study is to examine the effects of moving wall on the mixed convection flow and heat transfer in a right-angle triangular cavity filled with a micropolar fluid. Design/methodology/approach It is assumed that the bottom wall is uniformly heated and the right inclined wall is cold, whereas the vertical wall is adiabatic and moving with upward/downward velocity v0/−v0, respectively. The micropolar fluid is considered to satisfy the Boussinesq approximation. The governing equations and boundary conditions are solved using the Galerkin finite element method. The Penalty method is used to eliminate the pressure term from the momentum equations. To accomplish the consistent solution, the value of the penalty parameter is taken 107. The simulations are performed for a wide range of Richardson number, micropolar parameter, Prandtl number and Reynolds number. Findings The results are presented in the form of streamlines, isotherms and variations of average Nusselt number and fluid flow rate depending on the Richardson number, Prandtl number, micropolar parameter and direction of the moving wall. The flow field and temperature distribution in the cavity are affected by these parameters. An average Nusselt number into the cavity in both cases increase with increasing Prandtl and Richardson numbers and decreases with increasing micropolar parameter, and it has a maximum value when the lid is moving in the downward direction for all the physical parameters. Research limitations/implications The present investigation is conducted for the steady, two-dimensional mixed convective flow in a right-angle triangular cavity filled with micropolar fluid. An extension of the present study with the effects of cavity inclination, square cavity, rectangular, trapezoidal and wavy cavity will be the interest of future work. Originality/value This work studies the effects of moving wall, micropolar parameter, Richardson number, Prandtl number and Reynolds number parameter in a right-angle triangular cavity filled with a micropolar fluid on the fluid flow and heat transfer. This study might be useful to flows of biological fluids in thin vessels, polymeric suspensions, liquid crystals, slurries, colloidal suspensions, exotic lubricants, solar engineering for construction of triangular solar collector, construction of thermal insulation structure and geophysical fluid mechanics, etc.

Mixed Convection in Cooling of a Surface by Two-Dimensional Confined Slot Jet Impingement

2003 ◽  
Author(s):  
Dipankar Sahoo ◽  
M. A. R. Sharif
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Aspect Ratio ◽  
Transfer Process ◽  
Richardson Number ◽  
Average Nusselt Number ◽  
Heat Transfer Process ◽  
Two Dimensional ◽  
Hot Surface

The flow and heat transfer characteristics in the cooling of a heated surface by impinging confined jets have been investigated numerically through the steady state solution of laminar two-dimensional Navier-Stokes and energy equations. The principal objective of this study is to investigate the effect of buoyancy on the associated heat transfer process. Numerical computations are done for vertically downward directed two-dimensional confined slot jets impinging on a hot isothermal surface at the bottom. The computed flow patterns and isotherms for various domain aspect ratios and for a range of jet exit Reynolds numbers (100–500) and Richardson numbers (0–10) are analyzed to understand the heat transfer phenomena. The local and average Nusselt numbers at the hot surface for various conditions are compared. It is observed that for a given domain aspect ratio and Richardson number, the average Nusselt number at the hot surface increases with increasing jet exit Reynolds number. On the other hand, for a given aspect ratio and Reynolds number the average Nusselt number does not change significantly with Richardson number indicating that the buoyancy effects are not very significant on the overall heat transfer process for the range of jet Reynolds number considered in this study.

Analysis of Steady State Conjugate Heat Transfer in a Circular Microtube Inside a Substrate

2004 ◽  
Author(s):  
P. Sharath C. Rao ◽  
Muhammad M. Rahman
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Stainless Steel ◽  
Nusselt Number ◽  
Steady State ◽  
Maximum Temperature ◽  
Working Fluid ◽  
Thermal Conductivity Ratio ◽  
Interface Temperature ◽  
Outlet Temperature

The steady state heat transfer for laminar flow inside a circular microtube within a rectangular substrate has been investigated. Silicon, Silicon Carbide, and Stainless Steel were the substrates used and Water and FC-72 were the coolants employed. Equations governing the conservation of mass, momentum, and energy were solved in the fluid region. Within the solid wafer, the heat conduction was solved. A thorough investigation for velocity and temperature distributions for different substrates and coolants was performed by varying geometrical dimensions and Reynolds number. At a constant diameter and Reynolds number, for combinations comprising same coolant but different substrates, one with the lowest solid to fluid thermal conductivity ratio (ks/kf) attains the highest local peripheral average interface temperature. It was found that the Nusselt number is more for a system with Silicon as the substrate and FC-72 as the working fluid and the least for a system with Stainless Steel as the substrate and Water as the working fluid. The lower ks/kf ratio of Stainless Steel-Water combination is the main reason for the lower Nusselt number. With the increase in hydraulic diameter and Reynolds number, the average Nusselt number increased. It was also observed that the maximum temperature of the substrate and hence the outlet temperature of the fluid increased as the Reynolds number decreased.

scholarly journals Thermally Developing Flow and Heat Transfer in Elliptical Minichannels with Constant Wall Temperature

Micromachines ◽  
2019 ◽  
Vol 10 (10) ◽  
pp. 713 ◽  
Author(s):  
Su ◽  
Duan ◽  
He ◽  
Ma ◽  
Xu
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Aspect Ratio ◽  
Local Nusselt Number ◽  
Three Dimensional ◽  
Concave Function ◽  
Maximum Effect ◽  
Constant Wall Temperature ◽  
Developing Flow

Laminar convective heat transfer of elliptical minichannels is investigated for hydrodynamically fully developed but thermal developing flow with no-slip condition. A three-dimensional numerical model is developed in different elliptical geometries with the aspect ratio varying from 0.2 to 1. The effect of Reynolds number (25 ≤ Re ≤ 2000) on the local Nusselt number is examined in detail. The results indicate that the local Nusselt number is a decreasing function of Reynolds number and it is sensitive to Reynolds number especially for Re less than 250. The effect of aspect ratio on local Nusselt number is small when compared with the effect of Reynolds number on local Nusselt number. The local Nusselt number is independent of cross-section geometry at the inlet. The maximum effect of aspect ratio on local Nusselt number arises at the transition section rather than the fully developed region. However, the non-dimensional thermal entrance length is a monotonic decreasing concave function of aspect ratio but a weak function of Reynolds number. Correlations for the local Nusselt number and the thermal developing length for elliptical channels are developed with good accuracy, which may provide guidance for design and optimization of elliptical minichannel heat sinks.

Numerical Analysis of Laminar Mixed Convection in a Lid Driven Square Cavity With an Isothermally Heated Square Internal Blockage

2012 ◽  
Author(s):  
Akand W. Islam ◽  
Muhammad A. R. Sharif ◽  
Eric S. Carlson
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Mixed Convection ◽  
Richardson Number ◽  
Average Nusselt Number ◽  
Blockage Ratio ◽  
Square Cavity ◽  
Ansys Fluent ◽  
Laminar Mixed Convection

Laminar mixed convection characteristics in a square cavity with an isothermally heated square blockage inside have been investigated numerically using the finite volume method of the ANSYS FLUENT commercial CFD code. Various different blockage sizes and concentric and eccentric placement of the blockage inside the cavity have been considered. The blockage is maintained at a hot temperature, Th, and four surfaces of the cavity (including the lid) are maintained at a cold temperature, Tc, under all circumstances. The physical problem is represented mathematically by sets of governing conservation equations of mass, momentum, and energy. The geometrical and flow parameters for the problem are the blockage ratio (B), the blockage placement eccentricities (εx and εy), the Reynolds number (Re), the Grashof number (Gr), and the Richardson number (Ri). The flow and heat transfer behavior in the cavity for a range of Richardson number (0.01–100) at a fixed Reynolds number (100) and Prandtl number (0.71) is examined comprehensively. The variations of the average and local Nusselt number at the blockage surface at various Richardson numbers for different blockage sizes and placement eccentricities are presented. From the analysis of the mixed convection process, it is found that for any size of the blockage placed anywhere in the cavity, the average Nusselt number does not change significantly with increasing Richardson number until it approaches the value of the order of 1 beyond which the average Nusselt number increases rapidly with the Richardson number. For the central placement of the blockage at any fixed Richardson number, the average Nusselt number decreases with increasing blockage ratio and reaches a minimum at around a blockage ratio of slightly larger than 1/2. For further increase of the blockage ratio, the average Nusselt number increases again and becomes independent of the Richardson number. The most preferable heat transfer (based on the average Nusselt number) is obtained when the blockage is placed around the top left and the bottom right corners of the cavity.

Sign in / Sign up

Export Citation Format

Share Document