scholarly journals Fabrication and Physical Properties of Single-Crystalline Βeta-FeSi2 Nanowires

2020 ◽  
Vol 15 (1) ◽  
Author(s):  
Chih-Yung Yang ◽  
Shu-Meng Yang ◽  
Yu-Yang Chen ◽  
Kuo-Chang Lu
Keyword(s):  
Electron Microscopy ◽  
Physical Properties ◽  
Chemical Vapor ◽  
Chemical Vapor Deposition Method ◽  
Ferromagnetic Behavior ◽  
X Ray Diffraction ◽  
Field Emitters ◽  
Transmission Electron ◽  
Single Source Precursor ◽  
Carrier Gases

Abstract In this study, self-catalyzed β-FeSi2 nanowires, having been wanted but seldom achieved in a furnace, were synthesized via chemical vapor deposition method where the fabrication of β-FeSi2 nanowires occurred on Si (100) substrates through the decomposition of the single-source precursor of anhydrous FeCl3 powders at 750–950 °C. We carefully varied temperatures, duration time, and the flow rates of carrier gases to control and investigate the growth of the nanowires. The morphology of the β-FeSi2 nanowires was observed with scanning electron microscopy (SEM), while the structure of them was analyzed with X-ray diffraction (XRD) and transmission electron microscopy (TEM). The growth mechanism has been proposed and the physical properties of the iron disilicide nanowires were measured as well. In terms of the magnetization of β-FeSi2, nanowires were found to be different from bulk and thin film; additionally, longer β-FeSi2 nanowires possessed better magnetic properties, showing the room-temperature ferromagnetic behavior. Field emission measurements demonstrate that β-FeSi2 nanowires can be applied in field emitters.

Control of Morphology and Growth Direction of Gallium Nitride Nanostructures

2003 ◽  
Vol 789 ◽  
Author(s):  
Seung Yong Bae ◽  
Hee Won Seo ◽  
Jeunghee Park
Keyword(s):  
Electron Microscopy ◽  
Gallium Nitride ◽  
Large Scale ◽  
Chemical Vapor ◽  
Growth Direction ◽  
Chemical Vapor Deposition Method ◽  
X Ray Diffraction ◽  
Oxide Mixture ◽  
Temperature Range ◽  
Transmission Electron

ABSTRACTVarious shaped single-crystalline gallium nitride (GaN) nanostructures were produced by chemical vapor deposition method in the temperature range of 900–1200 °C. Scanning electron microscopy, transmission electron microscopy, electron diffraction, x-ray diffraction, electron energy loss spectroscopy, Raman spectroscopy, and photoluminescence were used to investigate the structural and optical properties of the GaN nanostructures. We controlled the GaN nanostructures by the catalyst and temperature. The cylindrical and triangular shaped nanowires were synthesized using iron and gold nanoparticles as catalysts, respectively, in the temperature range of 900 – 1000 °C. We synthesized the nanobelts, nanosaws, and porous nanowires using gallium source/ boron oxide mixture. When the temperature of source was 1100 °C, the nanobelts having a triangle tip were grown. At the temperature higher up to 1200 °C the nanosaws and porous nanowires were formed with a large scale. The cylindrical nanowires have random growth direction, while the triangular nanowires have uniform growth direction [010]. The growth direction of the nanobelts is perpendicular to the [010]. Interestingly, the nanosaws and porous nanowires exhibit the same growth direction [011]. The shift of Raman, XRD, and PL bands from those of bulk was correlated with the strains of the GaN nanostructures.

Effect of oxygen vacancies on the surface morphology and structural properties of WO3– x nanoparticles

2019 ◽  
Vol 9 (7) ◽  
pp. 773-777 ◽  
Author(s):  
Zhiguang Yang ◽  
Chaosheng Zhu ◽  
Zhiqiang Hou ◽  
Peng Peng
Keyword(s):  
Electron Microscopy ◽  
Active Sites ◽  
Oxygen Vacancies ◽  
Microwave Plasma ◽  
Chemical Vapor ◽  
Diffraction Field ◽  
Chemical Vapor Deposition Method ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Effect Of Oxygen

WO3 is an essential material for energy storage and catalytical technology, the oxygen vacancies level will play an essential role in its potential application. In this paper, porous tungsten oxide (WO3–x) with various oxygen contents was quickly fabricated by a microwave plasma-enhanced chemical vapor deposition method. A detailed characterization of structure and morphology features with the plasma handling process was recorded by X-ray diffraction, field-emission scanning electron microscopy and transmission electron microscopy, respectively. The etching mechanism of porous WO3–x under H2 plasma was discussed based on the systemically characterization. These results will help us to design the active sites or structure in the metal oxide materials.

Growth and Photoluminescence of β-SiC Nanowires on Porous Silicon Array

2013 ◽  
Vol 662 ◽  
pp. 11-15
Author(s):  
Hai Yan Wang ◽  
Li Ping Kang ◽  
Yong Qiang Wang ◽  
Zi Jiong Li
Keyword(s):  
Electron Microscopy ◽  
Porous Silicon ◽  
Chemical Vapor ◽  
Chemical Vapor Deposition Method ◽  
Fluorescent Light ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sic Nanowires ◽  
Quantum Confinement Effects ◽  
Transmission Electron

Nonaligned and curly β-SiC nanowires (nw-SiC) were grown on porous silicon array (PSA) by a chemical vapor deposition method with nickel as the catalyst. The morphology, structure and the composition of the nw-SiC/PSA and the SiC-SiO2core-shell fibers which is the semi-product were characterized by scanning electron microscopy, transmission electron microscopy and X-ray diffraction. Based on the experimental results a possible growth mechanism of nw-SiC was explained. Two broad photoluminescence peaks located around ~409 and ~494 nm were observed in nw-SiC/PSA in the PL measurement when utilizing 300 nm ultraviolet fluorescent light excited at room temperature. The excellent luminescent performances are ascribed to the quantum confinement effects in nw-SiC. The optical merits of nw-SiC/PSA made it a promising material in the fields of ultraviolet-blue emitting devices.

scholarly journals Synthesis and Optical Properties of CdSxSe1-x Semiconductor Nanomaterials by Chemical Vapor Deposition Method

2019 ◽  
Vol 12 (3) ◽  
pp. 55-64
Author(s):  
Nadia M. Jassim
Keyword(s):  
Electron Microscopy ◽  
Chemical Vapor Deposition ◽  
Vapor Deposition ◽  
Chemical Vapor ◽  
Growth Direction ◽  
Chemical Vapor Deposition Method ◽  
X Ray Diffraction ◽  
Selected Area Electron Diffraction ◽  
Transmission Electron ◽  
Vls Growth

Highly pure and crystalline CdSxSe1 -x nanostructures have been successfully synthesized via Chemical Vapor Deposition (CVD) method, changing the components of x, in order to adjust the band gap of materials, and the relationship with the lattice constant. Using X-ray Diffraction (XRD) to characterize the phase structures and elemental compositions of the samples, and using Field Emission Scanning Electron Microscopy (FESEM) to observe the surface morphology of CdSxSe1 -x nanomaterials and confirm the VLS growth mechanism. Using the High Resolution Transmission Electron Microscopy (HRTEM) and Selected Area Electron Diffraction (SAED) to analyze the crystal structure and the growth direction of the materials

scholarly journals Controlled Synthesis of CuS and Cu9S5 and Their Application in the Photocatalytic Mineralization of Tetracycline

Catalysts ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 899
Author(s):  
Murendeni P. Ravele ◽  
Opeyemi A. Oyewo ◽  
Damian C. Onwudiwe
Keyword(s):  
Electron Microscopy ◽  
Visible Light ◽  
Blue Shift ◽  
X Ray Diffraction ◽  
X Ray ◽  
Copper Sulfides ◽  
Transmission Electron ◽  
Single Source Precursor ◽  
Pure Phase ◽  
Pure Phases

Pure-phase Cu2−xS (x = 1, 0.2) nanoparticles have been synthesized by the thermal decomposition of copper(II) dithiocarbamate as a single-source precursor in oleylamine as a capping agent. The compositions of the Cu2−xS nanocrystals varied from CuS (covellite) through the mixture of phases (CuS and Cu7.2S4) to Cu9S5 (digenite) by simply varying the temperature of synthesis. The crystallinity and morphology of the copper sulfides were studied using X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM), which showed pure phases at low (120 °C) and high (220 °C) temperatures and a mixture of phases at intermediate temperatures (150 and 180 °C). Covellite was of a spherical morphology, while digenite was rod shaped. The optical properties of these nanocrystals were characterized by UV−vis–NIR and photoluminescence spectroscopies. Both samples had very similar absorption spectra but distinguishable fluorescence properties and exhibited a blue shift in their band gap energies compared to bulk Cu2−xS. The pure phases were used as catalysts for the photocatalytic degradation of tetracycline (TC) under visible-light irradiation. The results demonstrated that the photocatalytic activity of the digenite phase exhibited higher catalytic degradation of 98.5% compared to the covellite phase, which showed 88% degradation within the 120 min reaction time using 80 mg of the catalysts. The higher degradation efficiency achieved with the digenite phase was attributed to its higher absorption of the visible light compared to covellite.

Low Temperature Large Scale CVD Synthesis of Nano Onion-Like Fullerenes

2012 ◽  
Vol 490-495 ◽  
pp. 3211-3214 ◽  
Author(s):  
Lei Shan Chen ◽  
Cun Jing Wang
Keyword(s):  
Electron Microscopy ◽  
Low Temperature ◽  
Aluminum Hydroxide ◽  
Large Scale ◽  
Iron Catalyst ◽  
Chemical Vapor ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Naoh Solution ◽  
Synthesis Reactions

Synthesis reactions were carried out by chemical vapor deposition using iron catalyst supported on aluminum hydroxide at 400 °C and 420 °C, in the presence of argon as carrier gas and acetylene as carbon source. The aluminum hydroxide support was separated by refluxing the samples in 40% NaOH solution for 2 h and 36% HCl solution for 24 h, respectively. The samples were characterized by field-emission scanning electron microscopy, energy dispersive spectroscopy, high-resolution transmission electron microscopy and X-ray diffraction. The results show that carbon nanotubes were the main products at 420 °C, while large scale high purity nano onion-like fullerenes encapsulating Fe3C, with almost uniform sizes ranging from 10-50 nm, were obtained at the low temperature of 400 °C.

Effect of hydrothermal dwell time on the diameter-controlled synthesis and magnetic property of MnO2 nanorods

2014 ◽  
Vol 28 (06) ◽  
pp. 1450045 ◽  
Author(s):  
Arbab Mohammad Toufiq ◽  
Fengping Wang ◽  
Qurat-ul-Ain Javed ◽  
Yan Li
Keyword(s):  
Electron Microscopy ◽  
Reaction Time ◽  
Dwell Time ◽  
Hydrothermal Reaction ◽  
Ferromagnetic Behavior ◽  
X Ray Diffraction ◽  
Hydrothermal Route ◽  
Transmission Electron ◽  
Facile Hydrothermal Route ◽  
Hydrothermal Reaction Time

In this paper, single crystalline 1D tetragonal MnO 2 pen-type nanorods were synthesized by varying the dwell time through a facile hydrothermal route at a reaction temperature of 250°C. X-ray diffraction (XRD) and transmission electron microscopy (TEM) studies showed that the diameter of MnO 2 nanorods decreases from 460 nm to 250 nm with the increase in hydrothermal reaction time from 5 h to 15 h. Field-emission scanning electron microscopy (FESEM) and TEM studies revealed the evolution of improved surface morphology of MnO 2 nanorods that are prepared with longer hydrothermal reaction time. The magnetic properties of the products were evaluated using vibrating sample magnetometer (VSM) at room temperature, which showed that the as-prepared samples exhibit weak ferromagnetic behavior. The effect of diameter on the magnetization values was observed and discussed in detail.

Understanding the Growth Mechanisms of Tin Oxide Nanowires by Chemical Vapor Deposition

2021 ◽  
Vol 21 (4) ◽  
pp. 2538-2544
Author(s):  
Nguyen Minh Hieu ◽  
Nguyen Hoang Hai ◽  
Mai Anh Tuan
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Chemical Vapor Deposition ◽  
Vapor Deposition ◽  
Chemical Vapor ◽  
Chemical Mapping ◽  
X Ray Diffraction ◽  
Lattice Constants ◽  
Transmission Electron ◽  
Scanning Transmission

Tin oxides nanowires were prepared by chemical vapor deposition using shadow mask. X-ray diffraction indicated that the products were tetragonal having crystalline structure with lattice constants a = 0.474 nm and c = 0.318 nm. The high-resolution transmission electron microscopy revealed that inter planar spacing is 0.25 nm. The results chemical mapping in scanning transmission electron microscopy so that the two elements of Oxygen and Tin are distributed very homogeneously in nanowires and exhibit no apparent elements separation. A bottom-up mechanism for SnO2 growth process has been proposed to explain the morphology of SnO2 nanowires.

Fe-encapsulating carbon nano onionlike fullerenes from heavy oil residue

2008 ◽  
Vol 23 (5) ◽  
pp. 1393-1397 ◽  
Author(s):  
Yongzhen Yang ◽  
Xuguang Liu ◽  
Bingshe Xu
Keyword(s):  
Electron Microscopy ◽  
Heavy Oil ◽  
Chemical Vapor ◽  
Catalyst Precursor ◽  
X Ray Diffraction ◽  
Self Assembling ◽  
Transmission Electron ◽  
Oil Residue ◽  
Heavy Oil Residue ◽  
Graphite Sheets

Fe-encapsulating carbon nano onionlike fullerenes (NOLFs) were obtained by chemical vapor deposition (CVD) using heavy oil residue as carbon source and ferrocene as catalyst precursor in an argon flow of 150 mL/min at 900 °C for 30 min. Field-emission scanning electron microscopy (FE-SEM), high-resolution transmission electron microscopy (HRTEM), energy-dispersive spectroscopy (EDS), x-ray diffraction (XRD), and Raman spectroscopy were used to characterize morphology and microstructure of the products. The results show that Fe-encapsulating NOLFs collected at the outlet zone of quartz tube had core/shell structures with sizes ranging from 3 to 6 nm and outer shells composed of poorly crystallized graphitic layers. Their growth followed particle self-assembling growth mechanism, and all atoms in the graphite sheets primarily arose from Fe-carbide nanoparticles.

Ge Growth on Nanostructured Silicon Surfaces

2005 ◽  
Vol 862 ◽  
Author(s):  
Ganesh Vanamu ◽  
Abhaya K. Datye ◽  
Saleem H. Zaidi
Keyword(s):  
Electron Microscopy ◽  
Dislocation Density ◽  
Full Width Half Maximum ◽  
Defect Density ◽  
Chemical Vapor ◽  
Silicon Surfaces ◽  
X Ray Diffraction ◽  
Etch Pit ◽  
Transmission Electron

AbstractWe report highest quality Ge epilayers on nanoscale patterned Si structures. 100% Ge films of 10 μm are deposited using chemical vapor deposition. The quality of Ge layers was examined using scanning electron microscopy (SEM), transmission electron microscopy (TEM), and high-resolution x-ray diffraction (HRXRD) measurements. The defect density was evaluated using etch pit density measurements. We have obtained lowest dislocation density (5×105 cm-2) Ge films on the nanopatterned Si structures. The full width half maximum peaks of the reciprocal space maps of Ge epilayers on the nanopatterned Si showed 93 arc sec. We were able to get rid of the crosshatch pattern on the Ge surface grown on the nanopatterned Si. We also showed that there is a significant improvement of the quality of the Ge epilayers in the nanopatterned Si compared to an unpatterned Si. We observed nearly three-order magnitude decrease in the dislocation density in the patterned compared to the unpatterned structures. The Ge epilayer in the patterned Si has a dislocation density of 5×105 cm-2 as compared to 6×108 cm-2 for unpatterned Si.

Sign in / Sign up

Export Citation Format

Share Document