Organic Materials for Green Electronics

2021 ◽  
pp. 69-83
Author(s):  
G. Vidya ◽  
Saravanan Subbiahraj ◽  
Praveen C. Ramamurthy
Keyword(s):  
Organic Materials ◽  
Green Electronics

Application of Improved Voltage Compensation in the SEM to Imaging of Organic Materials

1973 ◽  
Vol 31 ◽  
pp. 444-445
Author(s):  
P.J. Killingworth ◽  
M. Warren
Keyword(s):  
Electron Beam ◽  
Organic Materials ◽  
Operating Parameters ◽  
Low Density ◽  
Beam Diameter ◽  
Incident Electron Beam ◽  
Specimen Material ◽  
Voltage Compensation ◽  
Selection Of ◽  
Scanning Electron

Ultimate resolution in the scanning electron microscope is determined not only by the diameter of the incident electron beam, but by interaction of that beam with the specimen material. Generally, while minimum beam diameter diminishes with increasing voltage, due to the reduced effect of aberration component and magnetic interference, the excited volume within the sample increases with electron energy. Thus, for any given material and imaging signal, there is an optimum volt age to achieve best resolution.In the case of organic materials, which are in general of low density and electric ally non-conducting; and may in addition be susceptible to radiation and heat damage, the selection of correct operating parameters is extremely critical and is achiev ed by interative adjustment.

200kv superconducting cryo electron microscope

1987 ◽  
Vol 45 ◽  
pp. 642-643
Author(s):  
M. Iwatsuki ◽  
Y. Kokubo ◽  
Y. Harada ◽  
J. Lehman
Keyword(s):  
Electron Microscope ◽  
Structure Analysis ◽  
Organic Materials ◽  
Strong Interactions ◽  
Specimen Preparation ◽  
Great Effort ◽  
Electron Microscopic ◽  
Crystal Fields ◽  
Special Skill ◽  
Long Time

In recent years, the electron microscope has been significantly improved in resolution and we can obtain routinely atomic-level high resolution images without any special skill. With this improvement, the structure analysis of organic materials has become one of the interesting targets in the biological and polymer crystal fields.Up to now, X-ray structure analysis has been mainly used for such materials. With this method, however, great effort and a long time are required for specimen preparation because of the need for larger crystals. This method can analyze average crystal structure but is insufficient for interpreting it on the atomic or molecular level. The electron microscopic method for organic materials has not only the advantage of specimen preparation but also the capability of providing various information from extremely small specimen regions, using strong interactions between electrons and the substance. On the other hand, however, this strong interaction has a big disadvantage in high radiation damage.

STM of freeze-fracture replicas: Problems and promises

1993 ◽  
Vol 51 ◽  
pp. 68-69
Author(s):  
J. T. Woodward ◽  
J. A. N. Zasadzinski
Keyword(s):  
Scanning Tunneling Microscope ◽  
Organic Materials ◽  
Freeze Fracture ◽  
Atomic Resolution ◽  
Scanning Tunneling ◽  
Tunneling Microscope ◽  
Molecular Scale ◽  
Organic Surfaces ◽  
Metal Layers ◽  
Conductive Surfaces

The Scanning Tunneling Microscope (STM) offers exciting new ways of imaging surfaces of biological or organic materials with resolution to the sub-molecular scale. Rigid, conductive surfaces can readily be imaged with the STM with atomic resolution. Unfortunately, organic surfaces are neither sufficiently conductive or rigid enough to be examined directly with the STM. At present, nonconductive surfaces can be examined in two ways: 1) Using the AFM, which measures the deflection of a weak spring as it is dragged across the surface, or 2) coating or replicating non-conductive surfaces with metal layers so as to make them conductive, then imaging with the STM. However, we have found that the conventional freeze-fracture technique, while extremely useful for imaging bulk organic materials with STM, must be modified considerably for optimal use in the STM.

Stabilizing pyritic material

1989 ◽  
Vol 4 ◽  
pp. 244-248 ◽  
Author(s):  
Donald L. Wolberg
Keyword(s):  
Significant Contribution ◽  
Organic Materials ◽  
Sedimentary Rocks ◽  
Iron Sulfides ◽  
Decomposition Products ◽  
Iron Minerals ◽  
Pyrite Formation ◽  
Organic Sediments ◽  
Freshwater Environments

The minerals pyrite and marcasite (broadly termed pyritic minerals) are iron sulfides that are common if not ubiquitous in sedimentary rocks, especially in association with organic materials (Berner, 1970). In most marine sedimentary associations, pyrite and marcasite are associated with organic sediments rich in dissolved sulfate and iron minerals. Because of the rapid consumption of sulfate in freshwater environments, however, pyrite formation is more restricted in nonmarine sediments (Berner, 1983). The origin of the sulfur in nonmarine environments must lie within pre-existing rocks or volcanic detritus; a relatively small, but significant contribution may derive from plant and animal decomposition products.

‘Robenhausien’ in the Hunterian Museum

1981 ◽  
Vol 8 (1) ◽  
pp. 1-12
Author(s):  
Isobel M Hughes
Keyword(s):  
Organic Materials ◽  
Neolithic Period ◽  
Plant Remains ◽  
Neolithic Europe ◽  
The University

Summary A report is presented of a study of the material from Robenhausen and other sites of the Neolithic period in Switzerland, part of the Bishop Collection in the Hunterian Museum, the University of Glasgow. The material is described and its likely setting within the cultural sequence of the Swiss Neolithic is discussed. The importance of the collection is seen to lie in the finds of organic materials, artefacts and macroscopic plant remains, which afford a rare glimpse of detail in craftsmanship and husbandry in Neolithic Europe.

Simple Modification Measurement of Photodegradability of Polymers by using Photo-induced Chemiluminescence Technique

2013 ◽  
Vol 10 (2) ◽  
pp. 51
Author(s):  
Siti Farhana Zakaria ◽  
Keith R Millington
Keyword(s):  
Free Radicals ◽  
Organic Materials ◽  
Oxidative Degradation ◽  
Working Life ◽  
Bimolecular Reaction ◽  
Synthetic Polymers ◽  
Accelerated Weathering ◽  
Simple Modification ◽  
Uv Absorbers ◽  
Irradiation Period

Polymers and organic materials that are exposed to sunlight undergo photooxidation, which leads to deterioration of their physical properties. To allow adequate performance under outdoor conditions, synthetic polymers require additives such as antioxidants and UV absorbers. A major problem with optimising polymer formulations to maximise their working life span is that accelerated weathering tests are empirical. The conditions differ significantly from real weathering situations, and samples require lengthy irradiation period. Degradation may not be apparent in the early stages of exposure, although this is when products such as hydroperoxides are formed which later cause acceleration of oxidation. A simple way of quantifying the number of free radicals presents in organic materials following exposure to light or heat is by measuring chemiluminescence (CL) emission. Most polymers emit CL when they undergo oxidative degradation, and it originates from the bimolecular reaction of macroperoxy radicals which creates an excited carbonyl.

Sign in / Sign up

Export Citation Format

Share Document