Determination of AASHTO 1993 layer coefficients considering time- and temperature-dependency of the asphalt mixture

2017 ◽  
pp. 523-529
Author(s):  
M. Lanotte ◽  
M.E. Kutay
Keyword(s):  
Asphalt Mixture ◽  
Temperature Dependency ◽  
Aashto 1993

scholarly journals Determination of Construction Parameters of Porous Ultra-Thin Overlays Based on Laboratory Compaction Studies

Materials ◽  
2020 ◽  
Vol 13 (20) ◽  
pp. 4496
Author(s):  
Jiahao Tian ◽  
Sang Luo ◽  
Ziming Liu ◽  
Xu Yang ◽  
Qing Lu
Keyword(s):  
Asphalt Concrete ◽  
Asphalt Mixture ◽  
Asphalt Mixtures ◽  
Combination Method ◽  
Compaction Temperature ◽  
Pavement Maintenance ◽  
Energy Equivalence ◽  
New Type ◽  
Better Than

To address the severe distresses of asphalt pavement, a new type of pavement maintenance treatment, porous ultra-thin overlay (PUTO) with small particle size was proposed. The PUTO has a thickness of 1.5–2.5 cm and a large void ratio of 18–25%. As a newly asphalt mixture, the structure characteristics differ from poor traditional pavement. Therefore, it is necessary to investigate the fabrication schemes in laboratory and on-site, respectively. In this study, the optimal fabrication schemes, including compaction temperature and number of blows of PUTO were determined based on Cantabro test and volumetric parameters. Then, the corresponding relationship between laboratory and on-site compaction work was then established based on the energy equivalent principle. On this basis, the numbers of on-site rolling passes and the combination method were calculated. The results show that increased compaction temperature and number of blows reduce the height and enhance the compaction of the Marshall sample. With the same temperature and number of blows, the raveling resistance of coarse gradation, Pavement Asphalt Concrete-1 (PAC-1) is better than that of fine gradation, Pavement Asphalt Concrete-2 (PAC-2), and the increased asphalt viscosity significantly improves the raveling resistance of the asphalt mixture. To ensure the scattering resistance and volumetric characteristic, the initial compaction temperature of the PAC-1 and PAC-2 should not be lower than 150 °C and 165 °C, respectively. Then, the laboratory compaction work and on-site compaction work were calculated and converted based on the principle of energy equivalence. Consequently, the on-site compaction combination of rolling machines for four asphalt mixtures was determined. According to the volumetric parameters, the paving test section proved that the construction temperature and the on-site rolling combination determined by laboratory tests are reasonable, and ultra-thin overlay has good structural stability, drainage, and skid resistance.

Interpretation of Transverse Profiles to Determine the Source of Rutting within an Asphalt Pavement System

2005 ◽  
Vol 1905 (1) ◽  
pp. 73-81 ◽  
Author(s):  
Claude Villiers ◽  
Reynaldo Roque ◽  
Bruce Dietrich
Keyword(s):  
Surface Layer ◽  
Literature Review ◽  
Asphalt Pavement ◽  
Asphalt Mixture ◽  
Falling Weight Deflectometer ◽  
Relative Contribution ◽  
Transverse Profile ◽  
Falling Weight ◽  
Different Sources

The transverse profilograph has been recognized as one of the most accurate devices for the measurement of rut depth. However, interpretation of surface transverse profile measurements poses a major challenge in determining the contributions of the different layers to rutting. A literature review has shown that the actual rutting mechanism can be estimated from a surface transverse profile for determination of the relative contribution of the layers to rutting. Unfortunately, much of the research yielded no verification or data. In addition, some techniques presented cannot be used if the rut depth is not well pronounced. Other techniques may be costly and time-consuming. The present research developed an approach that integrates ( a) falling weight deflectometer and core data along with 3.6-m transverse profile measurements to assess the contributions of different pavement layers to rutting and ( b) identifies the presence (or absence) of instability within the asphalt surface layer. This approach can be used regardless of the magnitude of the rut depth. On the basis of the analysis conducted, absolute rut depth should not be used to interpret the performance of the asphalt mixture. In addition, continued instability may not result in an increase in rut depth because the rutted basin broadens as traffic wander compacts or moves the dilated portion of the mixture. The approach developed appears to provide a reasonable way to distinguish between different sources of rutting. The conclusions drawn from analysis of the approach agreed well with observations from the trench cuts taken from four sections.

Research on Water Damage of Asphalt Pavement and Control Measures

2012 ◽  
Vol 178-181 ◽  
pp. 1560-1563 ◽  
Author(s):  
Yan Liu ◽  
Bo Liu
Keyword(s):  
Asphalt Pavement ◽  
Asphalt Mixture ◽  
Influence Factors ◽  
Water Source ◽  
Control Measures ◽  
Water Damage ◽  
Prevention And Control Measures ◽  
Pavement Damage ◽  
And Control

Asphalt pavement of water damage is a major form of our country highway asphalt pavement damage, the paper analyzes pavement structure internal water source, water damage of asphalt pavement of the influence factors, through the determination of the three indexes and asphalt of asphalt mixture splitting tensile strength, water erosion proof of asphalt mixture and its influence, and put forward the corresponding prevention and control measures to improve the pavement performance and extend the service life of road surface has important practical value.

scholarly journals Determination of Construction Parameters of Porous Ultra-Thin Overlays Based on Laboratory Compaction Studies

2020 ◽  
Author(s):  
Jiahao Tian ◽  
Sang Luo ◽  
Ziming Liu ◽  
Xu Yang ◽  
Qing Lu
Keyword(s):  
Void Ratio ◽  
Asphalt Mixture ◽  
Asphalt Mixtures ◽  
Combination Method ◽  
Compaction Temperature ◽  
Pavement Maintenance ◽  
Energy Equivalence ◽  
New Type ◽  
Better Than

To address the severe distresses of asphalt pavement, a new type of pavement maintenance treatment, porous ultra-thin overlay (PUTO) with small particle size was proposed. The PUTO has a thickness of 1.5~2.5 cm and a large void ratio of 18~25%. As a newly asphalt mixture, the structure characteristics differ from traditional pavement. Therefore, it is necessary to investigated the fabrication schemes in laboratory and on-site, respectively. In this study, the optimal fabrication schemes, including compaction temperature and number of blows of PUTO were determined based on Cantabro test and volumetric parameters. Then, the corresponding relationship between laboratory and on-site compaction work was then established based on the energy equivalent principle. On this basis, the numbers of on-site rolling passes and the combination method were calculated. The results show that increased compaction temperature and number of blows reduce the height and enhance the compactness of the Marshall sample. With the same temperature and number of blows, the scattering resistance of coarse gradation (PAC-1) is better than that of fine gradation (PAC-2), and the increased asphalt viscosity significantly improves the scattering resistance of the asphalt mixture. To ensure the scattering resistance and volumetric characteristic, the initial compaction temperature of the PAC-1 and PAC-2 should not be lower than 150 °C and 165 °C, respectively. Then, the laboratory compaction work and on-site compaction work were calculated and converted based on the principle of energy equivalence. Consequently, the on-site compaction combination of rolling machines for four asphalt mixtures was determined. According to the volumetric parameters, the paving test section proved that the construction temperature and the on-site rolling combination determined by laboratory tests are reasonable, and ultra-thin overlay has good structural stability, drainage and skid resistance.

scholarly journals Effect of percent air voids content on the deformation properties of the asphalt mixture

2021 ◽  
Vol 1209 (1) ◽  
pp. 012078
Author(s):  
J Bokomlasko ◽  
J Mandula
Keyword(s):  
Laboratory Tests ◽  
Asphalt Mixture ◽  
Road Construction ◽  
Air Voids ◽  
Aggregate Fraction ◽  
Deformation Properties ◽  
Load Effects ◽  
Air Void

Abstract Asphalt mixture is a building material with many advantages. Therefore, it is most used in road construction. If the asphalt mixture is laid with the prescribed technology, it can withstand load effects to long-term. It is necessary to take samples that will be subjected to laboratory measurements. There are several laboratory test, for example measurement thickness of the asphalt mixture layers, the aggregate fraction, quantity of binder in the mixture, determination of air void in asphalt mixture layers. Samples taken directly from the construction site are subjected to laboratory tests. This article focuses on one of the laboratory tests and it is determination of air void in asphalt mixture layers. The determination of air void in asphalt mixture layers is test in detail, because this effect has influence on the deformation properties of asphalt mixture layers. Therefore, it was necessary to model of air void in asphalt mixture layers with different degrees air void. On this purpose was use program Abaqus. The results were plotted. This graphs showed that increasing the air void in asphalt mixture layers has effect on the expansion of deformations. This can lead to faster pavement degradation.

Sign in / Sign up

Export Citation Format

Share Document