Combustion characteristics of natural-gas direct-injection combustion under various fuel injection timings

2003 ◽  
Vol 217 (5) ◽  
pp. 393-401 ◽  
Author(s):  
Z Huang ◽  
S Shiga ◽  
T Ueda ◽  
H Nakamura ◽  
T Ishima ◽  
...  
Keyword(s):  
Natural Gas ◽  
Fuel Injection ◽  
Direct Injection ◽  
Pressure Rise ◽  
Combustion Efficiency ◽  
Time Interval ◽  
Injection Timing ◽  
Ignition Timing ◽  
Fuel Injection Timing ◽  
Wide Range

The characteristics of natural-gas direct-injection combustion under various fuel injection timings were studied by using a rapid compression machine. Results show that natural-gas direct injection can result in combustion that is much faster than homogeneous combustion while shortening the time interval between injection timing and ignition timing can markedly decrease the combustion duration. Unburned hydrocarbon would increase over a wide range of equivalence ratios, shortening the time interval between injection timing and ignition timing can decrease the value to that of homogeneous-mixture combustion. The NOx level is high but the CO level is low over a wide range of equivalence ratios and is little affected by fuel injection timing. High values of pressure rise due to combustion can be realized and it is insensitive to the variation in fuel injection timing. High combustion efficiency can be achieved, which is also independent of injection timing.

Effect of Fuel Injection Timing Relative to Ignition Timing on the Natural-Gas Direct-Injection Combustion

2001 ◽  
Author(s):  
Zuohua Huang ◽  
Seiichi Shiga ◽  
Takamasa Ueda ◽  
Nobuhisa Jingu ◽  
Hisao Nakamura ◽  
...  
Keyword(s):  
Heat Release ◽  
Late Stage ◽  
Equivalence Ratio ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection Timing ◽  
Ignition Timing ◽  
Fuel Injection Timing ◽  
Initial Stage ◽  
Wide Range

Abstract Effect of fuel injection timing relative to ignition timing on natural gas direct-injection combustion was studied by using a rapid compression machine. The ignition timing was fixed at 80 ms from the compression start. When the injection timing was relatively earlier (injection start at 60 ms), the heat release pattern showed slower burn in the initial stage and faster burn in the late stage, which is similar to that of flame propagation of a premixed gas. In contrast to this, when the injection timing was relatively later (injection start at 75 ms), the heat release rate showed faster burn in the initial stage and slower burn in the late stage, which is similar to that of diesel combustion. The shortest duration was realized at the injection end timing of 80 ms (the same timing as the ignition timing) over the wide range of equivalence ratio. The degree of charge stratification and the intensity of turbulence generated by the fuel jet is considered to cause these behaviors. Earlier injection leads to longer duration of the initial combustion, whereas the later injection does longer duration of the late combustion. Earlier injection showed relatively lower CO emission while later injection produces relatively lower NOx emission. It was suggested that earlier injection leads to lower mixture stratification combustion and later injection leads to higher mixture stratification combustion. Combustion efficiency maintained high value over the wide range of equivalence ratio.

Effect of Fuel Injection Timing Relative to Ignition Timing on the Natural-Gas Direct-Injection Combustion

2003 ◽  
Vol 125 (3) ◽  
pp. 783-790 ◽  
Author(s):  
Z. Huang ◽  
S. Shiga ◽  
T. Ueda ◽  
H. Nakamura ◽  
T. Ishima ◽  
...  
Keyword(s):  
Late Stage ◽  
Equivalence Ratio ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection Timing ◽  
Ignition Timing ◽  
Fuel Injection Timing ◽  
Initial Stage ◽  
Wide Range ◽  
Early Injection

The effect of fuel injection timing relative to ignition timing on natural gas direct-injection combustion was studied by using a rapid compression machine (RCM). The ignition timing was fixed at 80 ms after the compression start. When the injection timing was relatively early (injection start at 60 ms), the heat release pattern showed a slower burn in the initial stage and a faster burn in the late stage, which is similar to that of flame propagation of a premixed gas. In contrast to this, when the injection timing was relatively late (injection start at 75 ms), the heat release rate showed a faster burn in the initial stage and a slower burn in the late stage, which is similar to that of diesel combustion. The shortest duration was realized at the injection end timing of 80 ms (the same timing as the ignition timing) over a wide range of equivalence ratio. The degree of charge stratification and the intensity of turbulence generated by the fuel jet are considered to cause this behavior. Early injection leads to longer duration of the initial combustion, whereas late injection leads to a longer duration of the late combustion. Early injection showed relatively lower CO concentration in the combustion products while late injection gave relatively lower NOx. It was suggested that early injection leads to combustion with weaker stratification, and late injection leads to combustion with stronger stratification. Combustion efficiency was kept at a high value over a wide range of equivalence ratio.

A study on premixed charge compression ignition combustion of natural gas with direct injection

2005 ◽  
Vol 6 (5) ◽  
pp. 443-451 ◽  
Author(s):  
T Ishiyama ◽  
H Kawanabe ◽  
K Ohashi ◽  
M Shioji ◽  
S Nakai
Keyword(s):  
Natural Gas ◽  
Fuel Injection ◽  
Direct Injection ◽  
Pressure Rise ◽  
Combustion Efficiency ◽  
Compression Ignition ◽  
Load Range ◽  
Injection Angle ◽  
Nozzle Orifice ◽  
Rich Mixture

In order to extend the available load range and obtain higher thermal efficiency in natural gas premixed charge compression ignition (PCCI) engines, a strategy for controlling direct injection combustion is discussed. Experimental results from single-cylinder engine tests demonstrate the possibility to extend load range by direct fuel injection. Reduced nozzle orifice size and reduced injection angle provide higher combustion efficiency; however, this promotes the tendency to knock because of the formation of a locally rich mixture. Arising from discussions based on prediction by computational fluid dynamics (CFD) code, considering mixture heterogeneity, it is suggested that controlling probability density functions (PDFs) of fuel concentration could be a means to control the rate of pressure rise. Restricted air utilization is useful to activate combustion at low overall equivalence ratios; on the other hand, full utilization of in-cylinder air and formation of a quantity of lean mixture can provide mild combustion.

Effect of Fuel Injection Timing During Negative Valve Overlap Period on a GDI-HCCI Engine

2018 ◽  
Author(s):  
Sok Ratnak ◽  
Jin Kusaka ◽  
Yasuhiro Daisho ◽  
Kei Yoshimura ◽  
Kenjiro Nakama
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Single Pulse ◽  
Injection Timing ◽  
Pulse Injection ◽  
Hcci Combustion ◽  
Fuel Injection Timing ◽  
Intake Stroke ◽  
Negative Valve Overlap ◽  
Valve Overlap

Gasoline Direct Injection Homogeneous Charge Compression (GDI-HCCI) combustion is achieved by closing early the exhaust valves for trapping hot residual gases combined with direct fuel injection. The combustion is chemically controlled by multi-point auto-ignition which its main combustion phase can be controlled by direct injection timing of fuel. This work investigates the effect of single pulse injection timing on a supercharged GDI-HCCI combustion engine by using a four-stroke single cylinder engine with a side-mounted direct fuel injector. Injection of primary reference fuel PRF90 under the near-stoichiometric-boosted condition is studied. The fuel is injected during negative valve overlap (NVO) or recompression period for fuel reformation under low oxygen concentration and the injection is retarded to intake stroke for the homogeneous mixture. It is found that the early fuel injection in NVO period advances the combustion phasing compared with the retarded injection in the intake stroke. Noticeable slower combustion rate from intake stroke fuel injection is obtained compared with the NVO injection due to charge cooling effect. Zero-dimensional combustion simulations with multiple chemical reaction mechanisms are simulated to provide chemical understanding from the effect of fuel injection timing on intermediate species generations. The species such as C2H4, C3H6, CH4, and H2 are found to be formed during the NVO injection period from the calculations. The effects of single pulse injection timings on combustion characteristics such pressure rise rate, combustion stability, and emissions are also discussed in this study.

Experimental investigations on combustion of jatropha methyl ester in a turbocharged direct-injection diesel engine

2008 ◽  
Vol 222 (10) ◽  
pp. 1865-1877 ◽  
Author(s):  
K Anand ◽  
R P Sharma ◽  
P S Mehta
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Diesel Fuel ◽  
Fuel Injection ◽  
Peak Pressure ◽  
Direct Injection ◽  
Pressure Rise ◽  
Experimental Investigations ◽  
Injection Timing ◽  
Gas Temperature

Suitability of vegetable oil as an alternative to diesel fuel in compression ignition engines has become attractive, and research in this area has gained momentum because of concerns on energy security, high oil prices, and increased emphasis on clean environment. The experimental work reported here has been carried out on a turbocharged direct-injection multicylinder truck diesel engine using diesel fuel and jatropha methyl ester (JME)-diesel blends. The results of the experimental investigation indicate that an increase in JME quantity in the blend slightly advances the dynamic fuel injection timing and lowers the ignition delay compared with the diesel fuel. A maximum rise in peak pressure limited to 6.5 per cent is observed for fuel blends up to 40 per cent JME for part-load (up to about 50 per cent load) operations. However, for a higher-JME blend, the peak pressures decrease at higher loads remained within 4.5 per cent. With increasing proportion of JME in the blend, the peak pressure occurrence slightly advances and the maximum rate of pressure rise, combustion duration, and exhaust gas temperature decrease by 9 per cent, 15 per cent and 17 per cent respectively. Although the changes in brake thermal efficiencies for 20 per cent and 40 per cent JME blends compared with diesel fuel remain insignificant, the 60 per cent JME blend showed about 2.7 per cent improvement in the brake thermal efficiency. In general, it is observed that the overall performance and combustion characteristics of the engine do not alter significantly for 20 per cent and 40 per cent JME blends but show an improvement over diesel performance when fuelled with 60 per cent JME blend.

Two-Stroke Engine with Fuel Semi-Direct Injection Using FAI System

2011 ◽  
Vol 130-134 ◽  
pp. 796-799
Author(s):  
Ming Ming Wu ◽  
Yan Xiang Yang ◽  
Da Guang Xi ◽  
Ping Zhang ◽  
Zhong Guo Jin
Keyword(s):  
Gasoline Engine ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection System ◽  
Injection Timing ◽  
Fuel System ◽  
Power Performance ◽  
Fuel Injection Timing ◽  
Injection Quantity ◽  
Stroke Engine

This paper presents the feasibility of semi-direct injection on a 50cm3, two-stroke motorcycle gasoline engine, which is applied FAI semi-direct injection fuel system. The structure and fuel injection system is improved based on the original carburetor engine and the FAI injector is easily installed. The results of laboratory and drive test show that, compared with the original carburetor fuel system, through optimization calibration of fuel injection timing and injection quantity can improve power performance and fuel economy.

Visualization study of natural gas direct injection combustion

2003 ◽  
Vol 217 (8) ◽  
pp. 667-676 ◽  
Author(s):  
Z Huang ◽  
S Shiga ◽  
T Ueda ◽  
H Nakamura ◽  
T Ishima ◽  
...  
Keyword(s):  
Natural Gas ◽  
High Speed ◽  
Fuel Injection ◽  
Single Injection ◽  
Direct Injection ◽  
Video Camera ◽  
Injection Timing ◽  
Lean Combustion ◽  
High Speed Video Camera ◽  
Wrinkled Flame

A visualization study of natural gas direct injection combustion was carried out by using a high speed video camera. The results show that the distribution of the stratified mixture di ers with the injection mode, with parallel and single injection tending to form a higher degree of mixture stratification than opposed injection. Flame propagates toward the downstream direction in the cases of parallel and single-injection combustion, and flame propagates outward from the centre of the combustion chamber in the case of opposed injection combustion. A characteristic of turbulent combustion with a wrinkled flame front is presented in natural gas direct injection combustion. Super-lean combustion can be realized owing to the formation of an ignitable stratified mixture with the optimum setting of the fuel injection timing.

Sign in / Sign up

Export Citation Format

Share Document