Measurements of real non-Newtonian response for liquid lubricants under moderate pressures

2001 ◽  
Vol 215 (3) ◽  
pp. 223-233 ◽  
Author(s):  
S Bair
Keyword(s):  
Numerical Simulation ◽  
Kinetic Theory ◽  
Simple Shear ◽  
Pressure Dependence ◽  
Shear Stresses ◽  
Current Interest ◽  
Flow Properties ◽  
Power Law Fluid ◽  
Temperature And Pressure

A thorough characterization of all viscous flow properties relevant to steady simple shear was carried out for five liquid lubricants of current interest to tribology. Shear stresses were generated to values significant to concentrated contact lubrication. Two types of non-Newtonian response were observed: shear-thinning as a power-law fluid and near rate-independence. Functions and parameters were obtained for the temperature and pressure dependence of the viscosity and of the time constant for the Carreau-Yasuda equation. Results are consistent with free volume and kinetic theory, but directly contradict many assumptions currently utilized for numerical simulation and for extracting rheological properties from contact measurements.

AEM analysis of crystallization in Ti-based amorphous alloys

1983 ◽  
Vol 41 ◽  
pp. 270-271
Author(s):  
A.R. Pelton ◽  
A.F. Marshall ◽  
Y.S. Lee
Keyword(s):  
Magnetic Properties ◽  
Amorphous Alloys ◽  
Amorphous Materials ◽  
Isothermal Annealing ◽  
Amorphous Matrix ◽  
Nucleation And Growth ◽  
Current Interest ◽  
Amorphous Films ◽  
Electrical And Magnetic Properties

Amorphous materials are of current interest due to their desirable mechanical, electrical and magnetic properties. Furthermore, crystallizing amorphous alloys provides an avenue for discerning sequential and competitive phases thus allowing access to otherwise inaccessible crystalline structures. Previous studies have shown the benefits of using AEM to determine crystal structures and compositions of partially crystallized alloys. The present paper will discuss the AEM characterization of crystallized Cu-Ti and Ni-Ti amorphous films.Cu60Ti40: The amorphous alloy Cu60Ti40, when continuously heated, forms a simple intermediate, macrocrystalline phase which then transforms to the ordered, equilibrium Cu3Ti2 phase. However, contrary to what one would expect from kinetic considerations, isothermal annealing below the isochronal crystallization temperature results in direct nucleation and growth of Cu3Ti2 from the amorphous matrix.

Evaluation of Different Turbulence Models for the Characterization of Shear Stresses in the Central Venous Access for Hemodialysis

2020 ◽  
Author(s):  
Saulo Gonçalves ◽  
Matheus Costa ◽  
Thabata Lucas ◽  
Jonathas Haniel ◽  
Mário Silva ◽  
...  
Keyword(s):  
Central Venous Access ◽  
Turbulence Models ◽  
Venous Access ◽  
Shear Stresses ◽  
Central Venous

Numerical study of electric field effects on the deformation of two-dimensional liquid drops in simple shear flow at arbitrary Reynolds number

2009 ◽  
Vol 626 ◽  
pp. 367-393 ◽  
Author(s):  
STEFAN MÄHLMANN ◽  
DEMETRIOS T. PAPAGEORGIOU
Keyword(s):  
Steady State ◽  
Shear Flow ◽  
Electric Field ◽  
Electric Fields ◽  
Simple Shear ◽  
Simple Shear Flow ◽  
Physical Parameters ◽  
Shear Stresses ◽  
Two Dimensional ◽  
Liquid Drops

The effect of an electric field on a periodic array of two-dimensional liquid drops suspended in simple shear flow is studied numerically. The shear is produced by moving the parallel walls of the channel containing the fluids at equal speeds but in opposite directions and an electric field is generated by imposing a constant voltage difference across the channel walls. The level set method is adapted to electrohydrodynamics problems that include a background flow in order to compute the effects of permittivity and conductivity differences between the two phases on the dynamics and drop configurations. The electric field introduces additional interfacial stresses at the drop interface and we perform extensive computations to assess the combined effects of electric fields, surface tension and inertia. Our computations for perfect dielectric systems indicate that the electric field increases the drop deformation to generate elongated drops at steady state, and at the same time alters the drop orientation by increasing alignment with the vertical, which is the direction of the underlying electric field. These phenomena are observed for a range of values of Reynolds and capillary numbers. Computations using the leaky dielectric model also indicate that for certain combinations of electric properties the drop can undergo enhanced alignment with the vertical or the horizontal, as compared to perfect dielectric systems. For cases of enhanced elongation and alignment with the vertical, the flow positions the droplets closer to the channel walls where they cause larger wall shear stresses. We also establish that a sufficiently strong electric field can be used to destabilize the flow in the sense that steady-state droplets that can exist in its absence for a set of physical parameters, become increasingly and indefinitely elongated until additional mechanisms can lead to rupture. It is suggested that electric fields can be used to enhance such phenomena.

Dynamic Characterization of a Valveless Micropump Considering Entrapped Gas Bubbles

2013 ◽  
Vol 135 (9) ◽  
Author(s):  
Songjing Li ◽  
Jixiao Liu ◽  
Dan Jiang
Keyword(s):  
Numerical Simulation ◽  
Theoretical Model ◽  
Experimental Studies ◽  
Gas Bubbles ◽  
Chamber Pressure ◽  
Dynamic Characterization ◽  
Valveless Micropump ◽  
Performance Deterioration ◽  
Trapped Gas

Unexpected gas bubbles in microfluidic devices always bring the problems of clogging, performance deterioration, and even device functional failure. For this reason, the aim of this paper is to study the characterization variation of a valveless micropump under different existence conditions of gas bubbles based on a theoretical modeling, numerical simulation, and experiment. In the theoretical model, we couple the vibration of piezoelectric diaphragm, the pressure drop of the nozzle/diffuser and the compressibility of working liquid when gas bubbles are entrapped. To validate the theoretical model, numerical simulation and experimental studies are carried out to investigate the variation of the pump chamber pressure influenced by the gas bubbles. Based on the numerical simulation and the experimental data, the outlet flow rates of the micropump with different size of trapped gas bubbles are calculated and compared, which suggests the influence of the gas bubbles on the dynamic characterization of the valveless micropump.

Measured temperature and pressure dependence of Vp and Vs in compacted, polycrystalline sI methane and sII methane–ethane hydrate

2003 ◽  
Vol 81 (1-2) ◽  
pp. 47-53 ◽  
Author(s):  
M B Helgerud ◽  
W F Waite ◽  
S H Kirby ◽  
A Nur
Keyword(s):  
High Pressure ◽  
Shear Wave ◽  
Pressure Dependence ◽  
Gas Hydrate ◽  
Pressure Vessel ◽  
Wave Speed ◽  
Measured Temperature ◽  
Shear Wave Speed ◽  
Temperature And Pressure ◽  
Fixed End

We report on compressional- and shear-wave-speed measurements made on compacted polycrystalline sI methane and sII methane–ethane hydrate. The gas hydrate samples are synthesized directly in the measurement apparatus by warming granulated ice to 17°C in the presence of a clathrate-forming gas at high pressure (methane for sI, 90.2% methane, 9.8% ethane for sII). Porosity is eliminated after hydrate synthesis by compacting the sample in the synthesis pressure vessel between a hydraulic ram and a fixed end-plug, both containing shear-wave transducers. Wave-speed measurements are made between –20 and 15°C and 0 to 105 MPa applied piston pressure. PACS No.: 61.60Lj

Sign in / Sign up

Export Citation Format

Share Document