scholarly journals Deriving the System of Fundamental Equations for Three-Dimensional Thermoelastic Field with Nonhomogeneous Material Properties and Its Application to a Thick Plate.

2000 ◽  
Vol 43 (3) ◽  
pp. 275-282
Author(s):  
Yoshinobu Tanigawa ◽  
Hiroyuki Morishita ◽  
Shigeo Ogaki
Keyword(s):  
Material Properties ◽  
Thick Plate ◽  
Three Dimensional ◽  
Nonhomogeneous Material ◽  
Thermoelastic Field ◽  
Fundamental Equations

Pavement Damage Due to Conventional and New Generation of Wide-Base Super Single Tires

2005 ◽  
Vol 33 (4) ◽  
pp. 210-226 ◽  
Author(s):  
I. L. Al-Qadi ◽  
M. A. Elseifi ◽  
P. J. Yoo ◽  
I. Janajreh
Keyword(s):  
Carrying Capacity ◽  
Material Properties ◽  
Three Dimensional ◽  
Fe Analysis ◽  
Load Carrying Capacity ◽  
Inflation Pressure ◽  
3D Finite Element ◽  
Load Carrying ◽  
Pavement Damage ◽  
New Generation

Abstract The objective of this study was to quantify pavement damage due to a conventional (385/65R22.5) and a new generation of wide-base (445/50R22.5) tires using three-dimensional (3D) finite element (FE) analysis. The investigated new generation of wide-base tires has wider treads and greater load-carrying capacity than the conventional wide-base tire. In addition, the contact patch is less sensitive to loading and is especially designed to operate at 690kPa inflation pressure at 121km/hr speed for full load of 151kN tandem axle. The developed FE models simulated the tread sizes and applicable contact pressure for each tread and utilized laboratory-measured pavement material properties. In addition, the models were calibrated and properly validated using field-measured stresses and strains. Comparison was established between the two wide-base tire types and the dual-tire assembly. Results indicated that the 445/50R22.5 wide-base tire would cause more fatigue damage, approximately the same rutting damage and less surface-initiated top-down cracking than the conventional dual-tire assembly. On the other hand, the conventional 385/65R22.5 wide-base tire, which was introduced more than two decades ago, caused the most damage.

scholarly journals Study on improving three-dimensional dynamic simulation model and equation of flexible fabric

2019 ◽  
Vol 11 (6) ◽  
pp. 168781401985284
Author(s):  
Meiliang Wang ◽  
Mingjun Wang ◽  
Xiaobo Li
Keyword(s):  
Simulation Model ◽  
Dynamic Simulation ◽  
Material Properties ◽  
Three Dimensional ◽  
Equation Solving ◽  
Study Results ◽  
Essential Properties ◽  
Dynamic Simulation Model ◽  
Novel Model ◽  
Simulation Equation

The use of the traditional fabric simulation model evidently shows that it cannot accurately reflect the material properties of the real fabric. This is against the background that the simulation result is artificial or an imitation, which leads to a low simulation equation. In order to solve such problems from occurring, there is need for a novel model that is designed to enhance the essential properties required for a flexible fabric, the simulation effect of the fabric, and the efficiency of simulation equation solving. Therefore, the improvement study results will offer a meaningful and practical understanding within the field of garment automation design, three-dimensional animation, virtual fitting to mention but a few.

scholarly journals The Effect of Material Properties on the Perceived Shape of Three-Dimensional Objects

i-Perception ◽  
2020 ◽  
Vol 11 (6) ◽  
pp. 204166952098231
Author(s):  
Masakazu Ohara ◽  
Juno Kim ◽  
Kowa Koida
Keyword(s):  
Material Properties ◽  
Regional Variation ◽  
Three Dimensional ◽  
Mean Square ◽  
Viewing Condition ◽  
Three Dimensional Objects ◽  
Transparent Objects ◽  
Dimensional Shape ◽  
Local Root ◽  
Three Dimensional Shape

Perceiving the shape of three-dimensional objects is essential for interacting with them in daily life. If objects are constructed from different materials, can the human visual system accurately estimate their three-dimensional shape? We varied the thickness, motion, opacity, and specularity of globally convex objects rendered in a photorealistic environment. These objects were presented under either dynamic or static viewing condition. Observers rated the overall convexity of these objects along the depth axis. Our results show that observers perceived solid transparent objects as flatter than the same objects rendered with opaque reflectance properties. Regional variation in local root-mean-square image contrast was shown to provide information that is predictive of perceived surface convexity.

Mechanics of Composite Layered Rough Medium in Contact

2013 ◽  
Vol 703 ◽  
pp. 200-203
Author(s):  
Shao Biao Cai ◽  
Yong Li Zhao
Keyword(s):  
Material Properties ◽  
Three Dimensional ◽  
Shear Stresses ◽  
Normal Loading ◽  
Layered Coatings ◽  
Pressure Profiles ◽  
Tangential Traction ◽  
Von Mises ◽  
Von Mises Stresses ◽  
Tangential Friction

This study presents a first attempt to develop a numerical three-dimensional multilayered (more than 2 composite layered coatings) elasticperfectly plastic rough solids model to investigate the contact behavior under combined normal loading and tangential traction. Contact analyses are performed to study the effects composite thin film layers. Local contact pressure profiles, von Mises stresses, and shear stresses as a function of material properties and applied normal and tangential friction loads are calculated.

scholarly journals On the Design of a Biodegradable POC-HA Polymeric Cardiovascular Stent

2012 ◽  
Author(s):  
Joonas Ponkala ◽  
Mohsin Rizwan ◽  
Panos S. Shiakolas
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Material Properties ◽  
Three Dimensional ◽  
Polymeric Composite ◽  
Coronary Stent ◽  
Element Analysis ◽  
Material Models ◽  
Solid Models ◽  
Biodegradable Stents

The current state of the art in coronary stent technology, tubular structures used to keep the lumen open, is mainly populated by metallic stents coated with certain drugs to increase biocompatibility, even though experimental biodegradable stents have appeared in the horizon. Biodegradable polymeric stent design necessitates accurate characterization of time dependent polymer material properties and mechanical behavior for analysis and optimization. This manuscript presents the process for evaluating material properties for biodegradable biocompatible polymeric composite poly(diol citrate) hydroxyapatite (POC-HA), approaches for identifying material models and three dimensional solid models for finite element analysis and fabrication of a stent. The developed material models were utilized in a nonlinear finite element analysis to evaluate the suitability of the POC-HA material for coronary stent application. In addition, the advantages of using femtosecond laser machining to fabricate the POC-HA stent are discussed showing a machined stent. The methodology presented with additional steps can be applied in the development of a biocompatible and biodegradable polymeric stents.

Sign in / Sign up

Export Citation Format

Share Document