von mises stresses
Recently Published Documents


TOTAL DOCUMENTS

139
(FIVE YEARS 53)

H-INDEX

9
(FIVE YEARS 2)

Aerospace ◽  
2022 ◽  
Vol 9 (1) ◽  
pp. 23
Author(s):  
Sarmad Dawood Salman Dawood ◽  
Ahmad Salahuddin Mohd Harithuddin ◽  
Mohammad Yazdi Harmin

Mass reduction is a primary design goal pursued in satellite structural design, since the launch cost is proportional to their total mass. The most common mass reduction method currently employed is to introduce honeycomb structures, with space qualified composite materials as facing materials, into the structural design, especially for satellites with larger masses. However, efficient implementation of these materials requires significant expertise in their design, analysis, and fabrication processes; moreover, the material procurement costs are high, therefore increasing the overall program costs. Thus, the current work proposes a low-cost alternative approach through the design and implementation of geometrically-shaped, parametrically-defined metal perforation patterns, fabricated by standard processes. These patterns included four geometric shapes (diamonds, hexagons, squares, and triangles) implemented onto several components of a structural design for a conceptual satellite, with a parametric design space defined by two scale factors and also two aspect ratio variations. The change in the structure’s fundamental natural frequency, as a result of implementing each pattern shape and parameter variation, was the selection criterion, due to its importance during the launcher selection process. The best pattern from among the four alternatives was then selected, after having validated the computational methodology through implementing experimental modal analysis on a scaled down physical model of a primary load-bearing component of the structural design. From the findings, a significant mass reduction percentage of 23.15%, utilizing the proposed perforation concept, was achieved in the final parametric design iteration relative to the baseline unperforated case while maintaining the same fundamental frequency. Dynamic loading analysis was also conducted, utilizing both the baseline unperforated and the finalized perforated designs, to check its capability to withstand realistic launch loads through applying quasi-static loads. The findings show that the final perforated design outperformed the baseline unperforated design with respect to the maximum displacements, maximum Von Mises stresses, and also the computed margin of safety. With these encouraging outcomes, the perforated design concept proved that it could provide an opportunity to develop low-cost satellite structural designs with reduced mass.


Author(s):  
Oleksiy Vodka ◽  
Ksenia Yevgenivna Potopalska

The work is devoted the definition of the function of limiting the geometric parameters of the steam turbine blade at given external loads. For this, a geometric model of a steam turbine blade was created, consisting of a blade body, a shank, and a shroud. The variable parameters were the angle of rotation of the middle section relative to the center of mass (which varied from 87 degrees to 92 degrees), as well as the length of the blade (varied from 495 mm to 525 mm). At the next stage, a finite element mesh was created. For the constructed model, an ordered finite element mesh was created in the area of the blade. Determined the stress-strain state of the blade during the operating mode. When carrying out the static analysis, an rotation velocity of 50 Hz was used as a load, and at the point of attachment of the disk in the shank, fixed displacement of all directions were used. The equivalent von Mises stresses and displacement in the structure are obtained. The zone of maximum stresses is located at the point where the blade is attached to the shank, but they do not exceed the limits. To determine the vibration characteristics of a steam turbine blade, its modal analysis was carried out taking into account the prestressed state from the action of static loads. The first six eigen modes of a steam turbine blade are obtained under the indicated initial conditions. The eigen frequency corresponding to the first form coincides with the rotational velocity (equal to 49 Hz), and the subsequent ones correspond to the multiplicities, respectively. At the next stage, a series of calculations was carried out to determine the response surface for the given parameters. The response surface for the maximum von Mises stresses and the first 4 modes of natural vibrations are determined. On the basis of the obtained results of studies of oscillations and deformed state of the blades with varying input parameters, it is possible to obtain a constraint for solving the optimization problem.


2021 ◽  
Vol 21 (1) ◽  
Author(s):  
Özge Özdal Zincir ◽  
Ateş Parlar

Abstract Background The All-on-four dental implant method is an implantology method designed to provide a comfortable prosthetic treatment option by avoiding advanced surgical procedures. This research aims to compare and evaluate the stress and tension values in conventional angled multiunit abutment-implant connection systems and monoblock dental implants used in the all-on-four procedure with finite element analysis. Methods Two master models were created by placing four implants connected to multiunit abutments (group A) in the interforaminal region of a completely edentulous mandible and four monoblock implants (group B) in the same region of another completely edentulous mandible. Group A implants were classified according to their diameter as follows: 3.5 mm (M1A), 4.0 mm (M2A), and 4.5 mm (M3A). Similarly, group B implants were classified as M1B, M2B, and M3B. In the six models rehabilitated with acrylic fixed prostheses, a 100 N force was applied to the anterior implant region, and a 250 N force was applied to the posterior cantilever in both axial and 30° oblique directions. Von Mises stresses were analyzed in the bone and implant regions of all models. Results M1A and M1B, M2A and M2B, and M3A and M3B were compared with each other under axial and oblique forces. The maximum Von Mises stresses in the bone around implants and the prosthesis screws, and the maximum and minimum principal stresses in the cortical and trabecular bone in group A models were significantly higher than those in group B models. Conclusions In monoblock implant systems under axial and oblique forces, higher stress is accumulated in the bone, prosthesis screw and implant compared to multiunit abutment-implant connection systems.


2021 ◽  
Vol 67 (1) ◽  
Author(s):  
Kaiting Zhang ◽  
Fuli Wang ◽  
Runmin Xu ◽  
Xinhui Fan ◽  
Bin Yan ◽  
...  

AbstractThe utilization of resourceful bamboo can alleviate the wood shortage problem. Bamboo-oriented strand board (BOSB) with the highest utilization of bamboo ratio and excellent mechanical properties was considered as a good engineering and furniture material. The strength of joints affects the safety of BOSB structure. This study aims to investigate the effect of screw spacing on the tensile and compressive stiffness and strength of corner joints from BOSB by experimental method combined with finite element method (FEM) compared with wood-oriented strand board (WOSB). The results showed that (1) the strength and stiffness of the corner joint was significantly affected by the screw spacing, and it affected the compressive strength and stiffness of WOSB more significantly; (2) the bending moment and stiffness coefficient of BOSB compressed joint decreased with the increase of spacing, while that of tensile joint increased first and then decreased, and it reached the maximum value, when the spacing was 48 mm; (3) compared with WOSB joint, BOSB joint had higher strength and stiffness, and the failure of the joint was due to the yielding of self-drilling screws. This was also verified by numerical analysis results; (4) the bending moment of BOSB joints was about 2.5 times that of WOSB joints, while the difference between stiffness coefficient was small; (5) the elastic deformations resulted from experimental tests and FEM are similar. It was shown that when the screw spacing is 48 mm, the Von Mises stresses on the BOSB joint were smaller, and the bending strength and stiffness were larger, which was the most suitable screw spacing.


2021 ◽  
Vol 32 (11) ◽  
Author(s):  
Hai-Jing Wang ◽  
Ye Yuan ◽  
Jing-Yu Tang ◽  
Quan Ji ◽  
Ling Kang ◽  
...  

AbstractThe beam windows of high-energy beam lines are important, and it is sometimes difficult to design because it is necessary to ensure particle propagation with minimum disturbance and fulfill mechanical requirements at the same time. The upstream decay pipe window of the long baseline neutrino facility at Fermilab has an extremely large diameter (1.8 m), with a thickness of only 1.5 mm to separate the helium atmosphere in the decay pipe and the nitrogen atmosphere on the other side. Furthermore, the center of this dish-shaped window is expected to be a 200-mm-diameter beryllium dish welded to the outside aluminum alloy A6061, and this welded combination must withstand extreme conditions of a 2.4-MW, high-energy proton beam without leakage. These severe conditions make the design of this window an unprecedented challenge. This paper describes the static thermal-structural analyses based on which the structure has been optimized, as well as dynamic analyses for understanding the shockwave effects originating in the beam. After optimization, the maximum von Mises stresses in the window decreased significantly in both normal operation and accident cases, making our design very reasonable.


2021 ◽  
Author(s):  
Takaaki Sato ◽  
Zachary Milne ◽  
Masahiro Nomura ◽  
Naruo Sasaki ◽  
Robert Carpick ◽  
...  

Abstract The behavior of materials in sliding contact is challenging to determine since the interface is normally hidden from view. Using a custom microfabricated device, we conducted in situ, ultrahigh vacuum transmission electron microscope measurements of crystalline silver nanocontacts under combined tension and shear, permitting simultaneous observation of contact forces and contact width. While classically, silver exhibits substantial sliding-induced plastic junction growth, the nanocontacts exhibit only limited plastic deformation despite high applied stresses. This difference arises from the nanocontacts’ high strength, as we find the von Mises stresses at yield points approach the ideal strength of silver. We attributed this to the nanocontacts’ nearly defect-free nature and small size. The contacts also separate unstably, with pull-off forces well below classical predictions for rupture under pure tension. This provides in situ confirmation that shearing reduces nanoscale pull-off forces, consistent with recent theoretical predictions but never before directly observed.


2021 ◽  
Vol 21 (1) ◽  
Author(s):  
Chunping Lin ◽  
Hongcheng Hu ◽  
Junxin Zhu ◽  
Yuwei Wu ◽  
Qiguo Rong ◽  
...  

Abstract Background Stress concentration may cause bone resorption even lead to the failure of implantation. This study was designed to investigate whether a certain sagittal root position could cause stress concentration around maxillary anterior custom-made root-analogue implants via three-dimensional finite element analysis. Methods The von Mises stresses in the bone around implants in different groups were compared by finite element analysis. Six models were constructed and divided into two groups through Geomagic Studio 2012 software. The smooth group included models of unthreaded custom-made implants in Class I, II or III sagittal root positions. The threaded group included models of reverse buttress-threaded implants in the three positions. The von Mises stress distributions and the range of the stresses under vertical and oblique loads of 100 N were analyzed through ANSYS 16.0 software. Results Stress concentrations around the labial lamella area were more prominent in the Class I position than in the Class II and Class III positions under oblique loading. Under vertical loading, the most obvious stress concentration areas were the labial lamella and palatal apical areas in the Class I and Class III positions, respectively. Stress was relatively distributed in the labial and palatal lamellae in the Class II position. The maximum von Mises stresses in the bone around the custom-made root-analogue implants in this study were lower than around traditional implants reported in the literature. The maximum von Mises stresses in this study were all less than 25 MPa in cortical bone and less than 6 MPa in cancellous bone. Additionally, compared to the smooth group, the threaded group showed lower von Mises stress concentration in the bone around the implants. Conclusions The sagittal root position affected the von Mises stress distribution around custom-made root-analogue implants. There was no certain sagittal root position that could cause excessive stress concentration around the custom-made root-analogue implants. Among the three sagittal root positions, the Class II position would be the most appropriate site for custom-made root-analogue implants.


2021 ◽  
Vol 10 (11) ◽  
pp. e579101119815
Author(s):  
Francisco Carlos dos Santos Reis ◽  
William Cunha Brandt ◽  
Letícia Cristina Cidreira Boaro ◽  
Milton Edson Miranda

The mechanical positioning behavior of a mal-positioned implant was evaluated in the finite element method. Models were created in SolidWorks Professional 2013® software with a single implant rehabilitation. The following were analyzed: Control Group, crown aligned to the implant long axis; Experimental Group, crown shifted 3 mm mesial proximally to the implant axis. Compressive stresses in cortical and medullary bone, and Von Mises stresses in implants and components were evaluated. With 100 N occlusal loading at 5 points. The peak von Mises stresses in the prosthetic screw of the experimental group (138.45 MPa) were 43.60% higher compared to the control group (96.41 MPa). The stresses in the prosthetic pillar were localized in the abutment region and the experimental group showed (875.63 MPa), 28% higher than the control group (683.88 MPa). Regarding the implant, the maximum stress peaks were located in the implant platform and the experimental group showed stress values of (1081.4) MPa and was 26.42% higher than the control 855.39 MPa. The cortical bone tissue of the experimental group showed shear stress values 10.81% higher than the control. The stress values were 151.36 MPa for the experimental group and (136.59 Mpa) for the control. The medullary bone showed shear stress (8.31 MPa) and was 12.29% higher than the control (7.40 MPa). A maximum peak was obtained in the cervical region of the medullary bone, adjacent to the cortical bone. The experimental group with a mal-positioned implant showed the highest maximum stresses for all simulated prosthetic components.


2021 ◽  
Vol 16 (1) ◽  
Author(s):  
Jian-jie Wang ◽  
Meng-lei Xu ◽  
Hui-zi Zeng ◽  
Liang-dong Zheng ◽  
Shi-jie Zhu ◽  
...  

Abstract Objective Preexisting severe cervical spinal cord compression is a significant risk factor in cervical hyperextension injury, and the neurological function may deteriorate after a slight force to the forehead. There are few biomechanical studies regarding the influence of pathological factors in hyperextension loading condition. The aim of this study is to analyze the effects of preexisting different types of cervical disc herniation and different degrees of compression on the spinal cord in cervical hyperextension. Method A 3D finite element (FE) model of cervical spinal cord was modeled. Local type with median herniation, local type with lateral herniation, diffuse type with median herniation, and diffuse type with lateral herniation were simulated in neutral and extention positions. The compressions which were equivalent to 10%, 20%, 30%, and 40% of the sagittal diameter of the spinal cord were modeled. Results The results of normal FE model were consistent with those of previous studies. The maximum von Mises stresses appeared in the pia mater for all 32 loading conditions. The maximum von Mises stresses in extension position were much higher than in neutral position. In most cases, the maximum von Mises stresses in diffuse type were higher than in local type. Conclusion Cervical spinal cord with preexisting disc herniation is more likely to be compressed in hyperextension situation than in neutral position. Diffuse type with median herniation may cause more severe compression with higher von Mises stresses concentrated at the anterior horn and the peripheral white matter, resulting in acute central cord syndrome from biomechanical point of view.


Sign in / Sign up

Export Citation Format

Share Document