Influence of inclination angle of trailing edge side on film cooling characteristics in hole shaped based on round holes with different sizes

2020 ◽  
Vol 2020 (0) ◽  
pp. 17B11
Author(s):  
Yuto NAKAMURA ◽  
Hiroshi SAITO
Keyword(s):  
Inclination Angle ◽  
Film Cooling ◽  
Trailing Edge ◽  
Edge Side

Impact of Different Film-Cooling Modes at Trailing Edge on the Aerodynamic Performance of Heavy Duty Gas Turbine Cascade

2011 ◽  
Vol 84-85 ◽  
pp. 259-263
Author(s):  
Xun Liu ◽  
Song Tao Wang ◽  
Xun Zhou ◽  
Guo Tai Feng
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Large Mass ◽  
Turbine Cascade ◽  
Heavy Duty ◽  
Trailing Edge ◽  
Central Difference ◽  
Adiabatic Effectiveness ◽  
Heavy Duty Gas Turbine ◽  
The Impact

In this paper, the trailing edge film cooling flow field of a heavy duty gas turbine cascade has been studied by central difference scheme and multi-block grid technique. The research is based on the three-dimensional N-S equation solver. By way of analysis of the temperature field, the distribution of profile pressure, and the distribution of film-cooling adiabatic effectiveness in the region of trailing edge with different cool air injection mass and different angles, it is found that the impact on the film-cooling adiabatic effectiveness is slightly by changing the injection mass. The distribution of profile pressure dropped intensely at the pressure side near the injection holes line with the large mass cooling air. The cooling effect is good in the region of trailing edge while the injection air is along the direction of stream.

Turbine Nozzle Endwall Phantom Cooling With Compound Angled Pressure Side Injection

2018 ◽  
Author(s):  
Kevin Liu ◽  
Hongzhou Xu ◽  
Michael Fox
Keyword(s):  
Film Cooling ◽  
High Speed ◽  
Axial Direction ◽  
Secondary Flows ◽  
Test Case ◽  
Pressure Side ◽  
Complex Flow ◽  
Trailing Edge ◽  
Cooling Effectiveness ◽  
Extended Area

Cooling of the turbine nozzle endwall is challenging due to its complex flow field involving strong secondary flows. Increasingly-effective cooling schemes are required to meet the higher turbine inlet temperatures required by today’s gas turbine applications. Therefore, in order to cool the endwall surface near the pressure side of the airfoil and the trailing edge extended area, the spent cooling air from the airfoil film cooling and pressure side discharge slots, referred to as “phantom cooling” is utilized. This paper studies the effect of compound angled pressure side injection on nozzle endwall surface. The measurements were conducted in a high speed linear cascade, which consists of three nozzle vanes and four flow passages. Two nozzle test models with a similar film cooling design were investigated, one with an axial pressure side film cooling row and trailing edge slots; the other with the same cooling features but with compound angled injection, aiming at the test endwall. Phantom cooling effectiveness on the endwall was measured using a Pressure Sensitive Paint (PSP) technique through the mass transfer analogy. Two-dimensional phantom cooling effectiveness distributions on the endwall surface are presented for four MFR (Mass Flow Ratio) values in each test case. Then the phantom cooling effectiveness distributions are pitchwise-averaged along the axial direction and comparisons were made to show the effect of the compound angled injection. The results indicated that the endwall phantom cooling effectiveness increases with the MFR significantly. A compound angle of the pressure side slots also enhanced the endwall phantom cooling significantly. For combined injections, the phantom cooling effectiveness is much higher than the pressure side slots injection only in the endwall downstream extended area.

Heat Transfer and Pressure Drop in a Converging Pedestal Array With Exit Area Variation

2018 ◽  
Author(s):  
L. W. Soma ◽  
F. E. Ames ◽  
S. Acharya
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Flow Rate ◽  
Film Cooling ◽  
Reynolds Numbers ◽  
Flow Path ◽  
Internal Cooling ◽  
Channel Measurements ◽  
Trailing Edge ◽  
Cooling Air

The trailing edge of a vane is one of the most difficult areas to cool due to a narrowing flow path, high external heat transfer rates, and deteriorating external film cooling protection. Converging pedestal arrays are often used as a means to provide internal cooling in this region. The thermally induced stresses in the trailing edge region of these converging arrays have been known to cause failure in the pedestals of conventional solidity arrays. The present paper documents the heat transfer and pressure drop through two high solidity converging rounded diamond pedestal arrays. These arrays have a 45 percent pedestal solidity. One array which was tested has nine rows of pedestals with an exit area in the last row consistent with the convergence. The other array has eight rows with an expanded exit in the last row to enable a higher cooling air flow rate. The expanded exit of the eight row array allows a 30% increase in the coolant flow rate compared with the nine row array for the same pressure drop. Heat transfer levels correlate well based on local Reynolds numbers but fall slightly below non converging arrays. The pressure drop across the array naturally increases toward the trailing edge with the convergence of the flow passage. A portion of the cooling air pressure drop can be attributed to acceleration while a portion can be attributed to flow path losses. Detailed array static pressure measurements provide a means to develop a correlation for the prediction of pressure drop across the cooling channel. Measurements have been acquired over Reynolds numbers based on exit flow conditions and the characteristic pedestal length scale ranging from 5000 to over 70,000.

Letterbox Trailing Edge Heat Transfer: Effects of Blowing Rate, Reynolds Number, and External Turbulence on Heat Transfer and Film Cooling Effectiveness

2009 ◽  
Vol 132 (1) ◽  
Author(s):  
N. J. Fiala ◽  
I. Jaswal ◽  
F. E. Ames
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Pressure Drop ◽  
Flow Rate ◽  
Film Cooling ◽  
Suction Surface ◽  
Trailing Edge ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Adiabatic Effectiveness

Heat transfer and film cooling distributions have been acquired for a vane trailing edge with letterbox partitions. Additionally, pressure drop data have been experimentally determined across a pin fin array and a trailing edge slot with letterbox partitions. The pressure drop across the array and letterbox trailing edge arrangement was measurably higher than for the gill slot geometry. Experimental data for the partitions and the inner suction surface region downstream from the slot have been acquired over a four-to-one range in vane exit condition Reynolds number (500,000, 1,000,000, and 2,000,000), with low (0.7%), grid (8.5%), and aerocombustor (13.5%) turbulence conditions. At these conditions, both heat transfer and adiabatic film cooling distributions have been documented over a range of blowing ratios (0.47≤M≤1.9). Heat transfer distributions on the inner suction surface downstream from the slot ejection were found to be dependent on both ejection flow rate and external conditions. Heat transfer on the partition side surfaces correlated with both exit Reynolds number and blowing ratio. Heat transfer on partition top surfaces largely correlated with exit Reynolds number but blowing ratio had a small effect at higher values. Generally, adiabatic film cooling levels on the inner suction surface are high but decrease near the trailing edge and provide some protection for the trailing edge. Adiabatic effectiveness levels on the partitions correlate with blowing ratio. On the partition sides adiabatic effectiveness is highest at low blowing ratios and decreases with increasing flow rate. On the partition tops adiabatic effectiveness increases with increasing blowing ratio but never exceeds the level on the sides. The present paper, together with a companion paper that documents letterbox trailing edge aerodynamics, is intended to provide engineers with the heat transfer and aerodynamic loss information needed to develop and compare competing trailing edge designs.

CFD Investigation of the Flow of Trailing Edge Cooling Slots

2018 ◽  
Author(s):  
Y. Jiang ◽  
N. Gurram ◽  
E. Romero ◽  
P. T. Ireland ◽  
L. di Mare
Keyword(s):  
Mach Number ◽  
Kinetic Energy ◽  
Flow Separation ◽  
Film Cooling ◽  
High Speed ◽  
Turbine Blades ◽  
Cross Flow ◽  
Turbulent Energy ◽  
Trailing Edge ◽  
Flow Interactions

Slot film cooling is a popular choice for trailing edge cooling in high pressure (HP) turbine blades because it can provide more uniform film coverage compared to discrete film cooling holes. The slot geometry consists of a cut back in the blade pressure side connected through rectangular openings to the internal coolant feed passage. The numerical simulation of this kind of film cooling flows is challenging due to the presence of flow interactions like step flow separation, coolant-mainstream mixing and heat transfer. The geometry under consideration is a cutback surface at the trailing edge of a constant cross-section aerofoil. The cutback surface is divided into three sections separated by narrow lands. The experiments are conducted in a high speed cascade in Oxford Osney Thermo-Fluids Laboratory at Reynolds and Mach number distributions representative of engine conditions. The capability of CFD methods to capture these flow phenomena is investigated in this paper. The isentropic Mach number and film effectiveness are compared between CFD and pressure sensitive paint (PSP) data. Compared to steady k–ω SST method, Scale Adaptive Simulation (SAS) can agree better with the measurement. Furthermore, the profiles of kinetic energy, production and shear stress obtained by the steady and SAS methods are compared to identify the main source of inaccuracy in RANS simulations. The SAS method is better to capture the unsteady coolant-hot gas mixing and vortex shedding at the slot lip. The cross flow is found to affect the film significantly as it triggers flow separation near the lands and reduces the effectiveness. The film is non-symmetric with respect to the half-span plane and different flow features are present in each slot. The effect of mass flow ratio (MFR) on flow pattern and coolant distribution is also studied. The profiles of velocity, kinetic energy and production of turbulent energy are compared among the slots in detail. The MFR not only affects the magnitude but also changes the sign of production.

Modeling and Impact of High-pressure Turbine Blade Trailing Edge Film Cooling Hole Variations

2020 ◽  
Author(s):  
Jan Kamenik ◽  
David J. Toal ◽  
Andy Keane ◽  
Lars Högner ◽  
Marcus Meyer ◽  
...  
Keyword(s):  
High Pressure ◽  
Turbine Blade ◽  
Film Cooling ◽  
High Pressure Turbine ◽  
Trailing Edge ◽  
Cooling Hole

Aerodynamics of a Letterbox Trailing Edge: Effects of Blowing Rate, Reynolds Number, and External Turbulence on Aerodynamic Losses and Pressure Distribution

2010 ◽  
Vol 132 (4) ◽  
Author(s):  
N. J. Fiala ◽  
J. D. Johnson ◽  
F. E. Ames
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Film Cooling ◽  
Large Scale ◽  
Reynolds Numbers ◽  
Design Flow ◽  
Trailing Edge ◽  
Film Cooling Effectiveness ◽  
Aerodynamic Loss ◽  
External Turbulence

A letterbox trailing edge configuration is formed by adding flow partitions to a gill slot or pressure side cutback. Letterbox partitions are a common trailing edge configuration for vanes and blades, and the aerodynamics of these configurations are consequently of interest. Exit surveys detailing total pressure loss, turning angle, and secondary velocities have been acquired for a vane with letterbox partitions in a large-scale low speed cascade facility. These measurements are compared with exit surveys of both the base (solid) and gill slot vane configurations. Exit surveys have been taken over a four to one range in chord Reynolds numbers (500,000, 1,000,000, and 2,000,000) based on exit conditions and for low (0.7%), grid (8.5%), and aerocombustor (13.5%) turbulence conditions with varying blowing rate (50%, 100%, 150%, and 200% design flow). Exit loss, angle, and secondary velocity measurements were acquired in the facility using a five-hole cone probe at a measuring station representing an axial chord spacing of 0.25 from the vane trailing edge plane. Differences between losses with the base vane, gill slot vane, and letterbox vane for a given turbulence condition and Reynolds number are compared providing evidence of coolant ejection losses, and losses due to the separation off the exit slot lip and partitions. Additionally, differences in the level of losses, distribution of losses, and secondary flow vectors are presented for the different turbulence conditions at the different Reynolds numbers. The letterbox configuration has been found to have slightly reduced losses at a given flow rate compared with the gill slot. However, the letterbox requires an increased pressure drop for the same ejection flow. The present paper together with a related paper (2008, “Letterbox Trailing Edge Heat Transfer—Effects of Blowing Rate, Reynolds Number, and External Turbulence on Heat Transfer and Film Cooling Effectiveness,” ASME, Paper No. GT2008-50474), which documents letterbox heat transfer, is intended to provide designers with aerodynamic loss and heat transfer information needed for design evaluation and comparison with competing trailing edge designs.

Pressure Side and Cutback Trailing Edge Film Cooling in a Linear Nozzle Vane Cascade at Different Mach Numbers

2012 ◽  
Vol 134 (5) ◽  
Author(s):  
Giovanna Barigozzi ◽  
Antonio Perdichizzi ◽  
Silvia Ravelli
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Pressure Side ◽  
Trailing Edge ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Mach Numbers ◽  
Nozzle Guide ◽  
Cooling Air ◽  
Momentum Boundary Layer

Tests on a specifically designed linear nozzle guide vane cascade with trailing edge coolant ejection were carried out to investigate the influence of trailing edge bleeding on both aerodynamic and thermal performance. The cascade is composed of six vanes with a profile typical of a high pressure turbine stage. The trailing edge cooling features a pressure side cutback with film cooling slots, stiffened by evenly spaced ribs in an inline configuration. Cooling air is ejected not only through the slots but also through two rows of cooling holes placed on the pressure side, upstream of the cutback. The cascade was tested for different isentropic exit Mach numbers, ranging from M2is = 0.2 to M2is = 0.6, while varying the coolant to mainstream mass flow ratio MFR up to 2.8%. The momentum boundary layer behavior at a location close to the trailing edge, on the pressure side, was assessed by means of laser Doppler measurements. Cases with and without coolant ejection allowed us to identify the contribution of the coolant to the off the wall velocity profile. Thermochromic liquid crystals (TLC) were used to map the adiabatic film cooling effectiveness on the pressure side cooled region. As expected, the cutback effect on cooling effectiveness, compared to the other cooling rows, was dominant.

Sign in / Sign up

Export Citation Format

Share Document