scholarly journals Experimental investigation on performance and emission characteristics of diesel - Jatropha methyl ester blends fueled diesel engine at optimum engine operating parameters

2010 ◽  
Vol 7 (2) ◽  
pp. 399-406 ◽  
Author(s):  
M. Venkatraman ◽  
G. Devaradjane
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Compression Ratio ◽  
Direct Injection ◽  
Engine Performance ◽  
Injection Pressure ◽  
Injection Timing ◽  
Performance And Emission ◽  
Performance And Emissions ◽  
Blended Fuel

In the present investigation, tests were carried out to determine engine performance, combustion and emissions of a naturally aspirated direct injection diesel engine fueled with diesel and Jatropha Methyl ester and their blends (JME10, JME20 and JME30). Comparison of performance and emission was done for different values of compression ratio, injection pressure and injection timing to find best possible combination for operating engine with JME. It is found that the combined compression ratio of 19:1, injection pressure of 240 bar and injection timing of 27?bTDC increases the BTHE and reduces BSFC while having lower emissions.From the investigation, it is concluded that the both performance and emissions can considerably improved for Methyl ester of jatropha oil blended fuel JME20 compared to diesel.

scholarly journals Modification of a Direct Injection Diesel Engine in Improving the Ignitability and Emissions of Diesel–Ethanol–Palm Oil Methyl Ester Blends

Energies ◽  
2019 ◽  
Vol 12 (14) ◽  
pp. 2644 ◽  
Author(s):  
Norhidayah Mat Taib ◽  
Mohd Radzi Abu Mansor ◽  
Wan Mohd Faizal Wan Mahmood
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Ambient Temperature ◽  
Palm Oil ◽  
Compression Ratio ◽  
Direct Injection ◽  
Cetane Number ◽  
Engine Performance ◽  
Injection Timing ◽  
Injection Strategies

Blending diesel with biofuels, such as ethanol and palm oil methyl ester (PME), enhances the fuel properties and produces improved engine performance and low emissions. However, the presence of ethanol, which has a small cetane number and low heating value, reduces the fuel ignitability. This work aimed to study the effect of injection strategies, compression ratio (CR), and air intake temperature (Ti) modification on blend ignitability, combustion characteristics, and emissions. Moreover, the best composition of diesel–ethanol–PME blends and engine modification was selected. A simulation was also conducted using Converge CFD software based on a single-cylinder direct injection compression ignition Yanmar TF90 engine parameter. Diesel–ethanol–PME blends that consist of 10% ethanol with 40% PME (D50E10B40), D50E25B25, and D50E40B10 were selected and conducted on different injection strategies, compression ratios, and intake temperatures. The results show that shortening the injection duration and increasing the injected mass has no significant effect on ignition. Meanwhile, advancing the injection timing improves the ignitability but with weak ignition energy. Therefore, increasing the compression ratio and ambient temperature helps ignite the non-combustible blends due to the high temperature and pressure. This modification allowed the mixture to ignite with a minimum CR of 20 and Ti of 350 K. Thus, blending high ethanol contents in a diesel engine can be applied by advancing the injection, increasing the CR, and increasing the ambient temperature. From the emission comparison, the most suitable mixtures that can be operated in the engine without modification is D50E25B25, and the most appropriate modification on the engine is by increasing the ambient temperature at 350 K.

Emulsified nano Al2O3 – Jatropha methyl ester blends: application in variable compression ratio engine

2020 ◽  
Vol 17 (5) ◽  
pp. 733-737
Author(s):  
Chiranjeeva Rao Seela ◽  
Ravi Sankar B.
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Compression Ratio ◽  
Engine Performance ◽  
Variable Compression Ratio ◽  
Content Type ◽  
Performance And Emission ◽  
Performance And Emissions ◽  
Improved Performance ◽  
Variable Compression

Purpose The purpose of this paper is to assess the influence of blends of Jatropha methyl ester (JME) and its nano Al2O3 emulsion on variable compression ratio diesel engine. The oxygen in alumina contributed for the smooth burning and resulted in improved performance and emissions. Design/Methodology/Approach The biodiesel (methyl ester) is prepared from the raw Jatropha oil. The B10, B20 and B30 blends of and their nanoemulsions are prepared with the 25, 50, 75 and 100 ppm of nano Al2O3. The prepared JME blends and its nanoemulsions are tested in a variable compression ratio (VCR) diesel engine to evaluate the engine performance and emission characteristics. Findings The nanoemulsion B20 + 50 ppm has given maximum brake thermal efficiency (BTE), and with the increased proportion of nanoparticle, the BTE was reduced. Also, the specific fuel consumption is lowest (0.2826 kg/kWh) for B20 + 50 ppm at the compression ratio 16.5 and full load which is 4.10% lower than the diesel and 5.8% lower than the B20 blend. As the load increases, NOx emission increases owing to higher peak temperatures in the combustion chamber. The JME-nano Al2O3 emulsion reduces the HC and CO emission compared with all other fuels. Originality/Value Novel nano emulsions are prepared, characterized and tested on VCR engine.

scholarly journals Influence of Ultra Injection Pressure with Dynamic Injection Timing on CRDI Engine Performance Using Simarouba Biodiesel Blends

2018 ◽  
Vol 15 (4) ◽  
pp. 5748-5759
Author(s):  
Srinath Pai ◽  
Abdul Sharief ◽  
Shiva Kumar
Keyword(s):  
Diesel Engine ◽  
High Speed ◽  
Direct Injection ◽  
Engine Performance ◽  
Injection Pressure ◽  
Injection Timing ◽  
Brake Thermal Efficiency ◽  
High Speed Diesel ◽  
Performance And Emissions ◽  
Smoke Opacity

A single cylinder diesel engine upgraded to operate Common Rail Direct Injection (CRDI) system and employed in this investigation. Tests were conducted on this engine using High-Speed diesel (HSD) and Simarouba biodiesel (SOME) blends to determine the influence of Injection Pressure (IP) and Injection Timing (IT) on the performance and emissions. Four unique IP of 400 bar to 1000 bar, in steps of 200 bar and four differing ITs of 10°, 13°, 15° and 18° before Top Dead Center (bTDC) combinations were attempted for the 25% to full load. Compression Ratio (CR) of 16.5 and Engine speed of 1500 RPM was kept constant during all trails. Critical performance parameter like Brake Thermal Efficiency (BTE) and Brake Specific Fuel Consumption (BSFC) were analyzed, primary emission parameters of the diesel engine The NOx and Smoke opacity were recorded. Finally, the outcomes of each combination were discussed.

Effect of Compression Ratio on Diesel Engine Performance and Emission Fueled with Tamanu Oil Methyl Ester and its Blends

2014 ◽  
Vol 984-985 ◽  
pp. 850-854 ◽  
Author(s):  
G. Antony Miraculas ◽  
N. Bose
Keyword(s):  
Diesel Engine ◽  
Compression Ratio ◽  
Direct Injection ◽  
Engine Performance ◽  
Calorific Value ◽  
Acid Value ◽  
Standard Test ◽  
Test Procedures ◽  
Performance And Emission ◽  
Acid And Base

Biofuels are renewable, nontoxic and ecofriendly fuels that can play an important role in automobile industries. They can successfully replace diesel fuel and helps in decreasing the import of crude oil. The discarded seed ofCalophyllunInophyllumwhich are planted in India mainly to prevent soil erosion is considered as the possible source for extracting biodiesel. Thetamanuoil extracted had a fatty acid value of 48 mg KOH/g, therefore a two stage esterification processes with acid and base catalyst were used for converting it into biodiesel. The fuel was then tested for properties such as viscosity, calorific value and carbon residue using standard test procedures and found to be analogous with diesel, which makes it possible to use this alternate fuel in the existing engine without any modification. A single cylinder, four stroke, constant speed, variable compression ratio, direct injection diesel engine developing 5KW power with provision for computerized data acquisition is used to evaluate the performance and emission characteristics. The test results were analyzed for biodiesel and its blends in comparison with standard diesel at different compression ratios (16:1, 18:1, 20:1 & 22:1). The performance and emission results of the diesel engine revealed that biodiesel can be blended with diesel up to 40% at an optimum CR of 20, in order to get improved performance and reduced emission.

scholarly journals Eucalyptus-Palm Kernel Oil Blends: A Complete Elimination of Diesel in a 4-Stroke VCR Diesel Engine

2015 ◽  
Vol 2015 ◽  
pp. 1-7 ◽  
Author(s):  
Srinivas Kommana ◽  
Balu Naik Banoth ◽  
Kalyani Radha Kadavakollu
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Compression Ratio ◽  
Alternative Fuels ◽  
Palm Kernel ◽  
Engine Performance ◽  
Palm Kernel Oil ◽  
Performance And Emission ◽  
Eucalyptus Oil ◽  
Kernel Oil

Fuels derived from biomass are mostly preferred as alternative fuels for IC engines as they are abundantly available and renewable in nature. The objective of the study is to identify the parameters that influence gross indicated fuel conversion efficiency and how they are affected by the use of biodiesel relative to petroleum diesel. Important physicochemical properties of palm kernel oil and eucalyptus blend were experimentally evaluated and found within acceptable limits of relevant standards. As most of vegetable oils are edible, growing concern for trying nonedible and waste fats as alternative to petrodiesel has emerged. In present study diesel fuel is completely replaced by biofuels, namely, methyl ester of palm kernel oil and eucalyptus oil in various blends. Different blends of palm kernel oil and eucalyptus oil are prepared on volume basis and used as operating fuel in single cylinder 4-stroke variable compression ratio diesel engine. Performance and emission characteristics of these blends are studied by varying the compression ratio. In the present experiment methyl ester extracted from palm kernel oil is considered as ignition improver and eucalyptus oil is considered as the fuel. The blends taken are PKE05 (palm kernel oil 95 + eucalyptus 05), PKE10 (palm kernel oil 90 + eucalyptus 10), and PKE15 (palm kernel 85 + eucalyptus 15). The results obtained by operating with these fuels are compared with results of pure diesel; finally the most preferable combination and the preferred compression ratio are identified.

Sign in / Sign up

Export Citation Format

Share Document