scholarly journals Study on Using Fly Ash for Fly Ash - Soil Piles in Reinforcing Soft Ground

2020 ◽  
Vol 8 (5) ◽  
pp. 1074-1085
Author(s):  
Tuan Anh Nguyen ◽  
Dat Thanh Nguyen ◽  
Tung Thanh Pham ◽  
Linh Truong Chau
Keyword(s):  
Fly Ash ◽  
2020 ◽  
Vol 61 (HTCS6) ◽  
pp. 1-9
Author(s):  
Thinh Duc Ta ◽  
Phuc Dinh Hoang ◽  
Thang Anh Bui ◽  
Trang Huong Thi Ngo ◽  
Diu Thi Nguyen ◽  
...  

Sea sand-cement-fly ash column technology for soft soil treatment is a new technology in the process of completing the theoretical basis, the experimental basis, and the construction of the ground treatment technological procedure. The paper presents the results of scientific research on design, calculation, construction, and acceptance of sea sand-cement-fly ash column. The scientific basis for the design of column is to consider the role of the column in composite ground, that is to use the column as soft ground improvement or soft soil reinforcement. The important parameters for the column design are: cement and fly ash content; column length; column diameter; number of columns; distance among columns; load capacity and settlement of composite ground. The sequence of steps of construction and acceptance of column includes: selection of construction equipment, preparation of construction sites, trial construction, official construction, evaluation of ground quality after treatment and preparation of document for acceptance.


2001 ◽  
Vol 38 (2) ◽  
pp. 276-286 ◽  
Author(s):  
A Porbaha ◽  
T BS Pradhan ◽  
T Kishida

This study presents the results of a series of monotonic undrained triaxial compression tests on clay specimens improved by columnar reinforcement. The process of loading and stress redistribution of a fly ash – clay specimen (FCS), in comparison with a sand–clay specimen (SCS), is examined in terms of stress–strain characteristics, generation of excess pore-water pressure, effective and total earth pressures, development of stress concentration, and the normalized undrained shear strength of the improved soil. It was found, predictably, that the deviator stress of the composite specimens was influenced by the consolidation stress, replacement area ratio, and properties of the column material. The stress concentration at the top of the composite ground which depends on the loading stage reaches a peak after the consolidation state and is reduced due to stress redistribution between the column and the soft ground. In terms of improvement effects, the mean shear strengths of FCS and SCS relative to the clay specimen are three and seven times greater, respectively, for a replacement area ratio of 49%.Key words: composite ground, fly ash, soil improvement, soft ground, triaxial test.


2018 ◽  
Vol 10 (5) ◽  
pp. 977-985 ◽  
Author(s):  
D. Xiao ◽  
G.L. Jiang ◽  
D. Liao ◽  
Y.F. Hu ◽  
X.F. Liu
Keyword(s):  
Fly Ash ◽  

2020 ◽  
Vol 6 (2) ◽  
pp. 225-237 ◽  
Author(s):  
Hussein H. Karim ◽  
Zeena W. Samueel ◽  
Adel H. Jassem

The effect of Cyclic loading on the foundation behaviour of many engineering structures presents more important and related to many problems in geotechnical engineering, Especially when construction on soft ground area which represent one of the major concerns in geotechnical engineering. This paper is conducted to investigate the influence of using several improving techniques as (fly ash, Geo-grid, fly ash and Geo-grid) on the behavior of soft clayey soil subjected to cyclic loading. A total of twenty four models have been tested  which consists of a wide domain of boundary conditions, such as untreated model, Geo-grid reinforced models, fly ash treated models and models treated with fly ash incorporated with Geo-grid were conducted by varying parameters such as, footing elevations, test velocity and number of geogrid layers. The analysis demonstrates that the settlement behaviour of footing resting on treated models with fly ash and two Geo-grid layers perform better than other improving techniques.  Also observed there was an increase in settlement, which corresponds to the increase in test velocity from 6 to 9 mm/sec. Furthermore, it was conducted that the more depth of footing the soil settlement decreases. In general, when other factors remaining constant, the bearing capacity of soil goes on increasing when the depth increased.


Author(s):  
L. L. Sutter ◽  
G. R. Dewey ◽  
J. F. Sandell

Municipal waste combustion typically involves both energy recovery as well as volume reduction of municipal solid waste prior to landfilling. However, due to environmental concerns, municipal waste combustion (MWC) has not been a widely accepted practice. A primary concern is the leaching behavior of MWC ash when it is stored in a landfill. The ash consists of a finely divided fly ash fraction (10% by volume) and a coarser bottom ash (90% by volume). Typically, MWC fly ash fails tests used to evaluate leaching behavior due to high amounts of soluble lead and cadmium species. The focus of this study was to identify specific lead bearing phases in MWC fly ash. Detailed information regarding lead speciation is necessary to completely understand the leaching behavior of MWC ash.


1997 ◽  
Vol 9 (6) ◽  
pp. 541-565 ◽  
Author(s):  
Cheryl R. Killingsworth ◽  
Francesca Alessandrini ◽  
G. G. Krishna Murthy ◽  
Paul J. Catalano ◽  
Joseph D. Paulauskis ◽  
...  

2021 ◽  
Vol 33 (3) ◽  
pp. 04021001
Author(s):  
Maheshbabu Jallu ◽  
Sireesh Saride ◽  
Arul Arulrajah ◽  
Subrahmanyam Challapalli ◽  
Robert Evans
Keyword(s):  
Fly Ash ◽  

Author(s):  
Shubham N. Dadgal ◽  
Shrikant Solanke

In modern days for structures in coastal areas it has been observed that the premature structural failures are occurs due to corrosion of the reinforcements of the designed structural member. The corrosion causes the structural damage which in turn leads to reduction in the bearing capacity of the concerned structural members. The aim of this study was to study the effect of partial replacement of fly ash to minimize the corrosion effect. Beams were designed and corroded by using artificial method known accelerated corrosion method. The beams were then tested for flexural and bond strength. Also the weight loss of the reinforced bars was been determined using electrical resistivity method. The fly ash will replace by 10% and 15%.The strength will calculate at varying percentage of corrosion at 10% and 15%. Beams will cast at M25 grade concrete. The flexural strength will test by using UTM and the bond strength will calculate using pullout test.


Sign in / Sign up

Export Citation Format

Share Document