Using Synchrotron-Based FT-IR Microspectroscopy to Study Erucamide Migration in 50-μm-thick Bilayer Linear Low-Density Polyethylene and Polyolefin Plastomer Films

2003 ◽  
Vol 57 (1) ◽  
pp. 37-43 ◽  
Author(s):  
Shilpa Y. Sankhe ◽  
Douglas E. Hirt
Keyword(s):  
Single Layer ◽  
Surface Concentration ◽  
Multilayer Films ◽  
Low Density Polyethylene ◽  
Concentration Profiles ◽  
Low Density ◽  
Additive Concentration ◽  
Linear Low Density Polyethylene ◽  
Ft Ir ◽  
Ir Microspectroscopy

The diffusion of additives in thick (∼500 μm) single layer and multilayer films has been characterized using FT-IR microspectroscopy.1,2 The objective of this research was to investigate additive migration and concentration profiles in coextruded multilayer films of industrially relevant thicknesses. In particular, the investigation focused on the migration of an erucamide slip agent in 50-μm-thick coextruded bilayer films of linear low-density polyethylene (LLDPE) and a polyolefin plastomer (POP). Erucamide concentration profiles were successfully mapped using synchrotron-based FT-IR microspectroscopy. The synchrotron radiation helped to achieve a higher spatial resolution for the thin films. Meticulous sample preparation was needed to map the thin film samples. Results with FT-IR microspectroscopy showed that the additive-concentration profiles were relatively uniform across the multilayer-film thickness irrespective of the intended initial additive distribution. For example, a bilayer planned for 1 wt % erucamide in an LLDPE layer and no erucamide in a POP layer showed significant additive migration into the POP layer at the extrusion rates used. FT-IR microspectroscopy results also showed that more erucamide migrated to the surface of a POP layer than an LLDPE layer. Attenuated total reflectance (ATR) FT-IR spectroscopy was used to confirm the time-dependent increase of erucamide surface concentration and that the increase was more pronounced at the surface of the POP layers.

Performance of multilayer films using maleated linear low-density polyethylene blends

1998 ◽  
Vol 38 (1) ◽  
pp. 150-155 ◽  
Author(s):  
S. Sánchez-Valdes ◽  
F. Orona-Villarreal ◽  
M. Lopez-Quintanilla ◽  
I. Yañez-Flores ◽  
L. F. Ramos De Valle ◽  
...  
Keyword(s):  
Multilayer Films ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Linear Low Density Polyethylene ◽  
Polyethylene Blends

Determination of the Percentage of Homopolymer Component in Ziegler/Natta Catalyst Linear Low-Density Polyethylene Resins Using High-Temperature Cell Fourier Transform Infrared and Partial Least Squares Quantitative Analysis Technique

2005 ◽  
Vol 59 (3) ◽  
pp. 300-304 ◽  
Author(s):  
Marlee Cossar ◽  
Joo Teh ◽  
Annikki Kivisto ◽  
Jason Mackenzie
Keyword(s):  
Fourier Transform ◽  
High Temperature ◽  
Quantitative Analysis ◽  
Ir Spectrum ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Linear Low Density Polyethylene ◽  
Analysis Technique ◽  
Ft Ir

A new method for the determination of the percentage of homopolymer component, using high-temperature cell Fourier transform infrared (FT-IR) by partial least squares (PLS) quantitative analysis technique, was developed and applied to Ziegler Natta linear low-density polyethylene (LLDPE). The method is based on the IR spectrum changes between the 730 cm−1 band and 720 cm−1 band at the temperature of 110 °C, which is near the melting point of the polyethylene. The HD% (the percentage of high-density component, i.e., the percentage of homopolymer component) results obtained by CTREF (CRYSTAF in TREF mode) technique are used as the input data together with the respective FT-IR spectra for PLS analyses to establish a calibration curve. The PLS quality is characterized by a correlation coefficient of 0.997 (cross-validation) using four factors and a root mean square error of calibration (RMSEC) of 0.772. The HD% of the unknown can then be predicted by the PLS software from the unknown FT-IR spectrum. A control resin was tested seven times by CTREF and FT-IR. The HD% of the control resin was 28.59 ± 0.88% by CTREF and 29.05 ± 2.37% by FT-IR. It was found that the method was applicable for the same comonomer type of LLDPE within a melt index range and density.

scholarly journals Identification of the LLDPE Constitutive Material Model for Energy Absorption in Impact Applications

Polymers ◽  
2021 ◽  
Vol 13 (10) ◽  
pp. 1537
Author(s):  
Luděk Hynčík ◽  
Petra Kochová ◽  
Jan Špička ◽  
Tomasz Bońkowski ◽  
Robert Cimrman ◽  
...  
Keyword(s):  
Strain Rate ◽  
Material Model ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Linear Low Density Polyethylene ◽  
Stress Strain ◽  
Rate Dependent ◽  
Constitutive Material Model ◽  
Principal Directions ◽  
Constitutive Material

Current industrial trends bring new challenges in energy absorbing systems. Polymer materials as the traditional packaging materials seem to be promising due to their low weight, structure, and production price. Based on the review, the linear low-density polyethylene (LLDPE) material was identified as the most promising material for absorbing impact energy. The current paper addresses the identification of the material parameters and the development of a constitutive material model to be used in future designs by virtual prototyping. The paper deals with the experimental measurement of the stress-strain relations of linear low-density polyethylene under static and dynamic loading. The quasi-static measurement was realized in two perpendicular principal directions and was supplemented by a test measurement in the 45° direction, i.e., exactly between the principal directions. The quasi-static stress-strain curves were analyzed as an initial step for dynamic strain rate-dependent material behavior. The dynamic response was tested in a drop tower using a spherical impactor hitting a flat material multi-layered specimen at two different energy levels. The strain rate-dependent material model was identified by optimizing the static material response obtained in the dynamic experiments. The material model was validated by the virtual reconstruction of the experiments and by comparing the numerical results to the experimental ones.

scholarly journals Polyethylene Migration from Food Packaging on Cheese Detected by Raman and Infrared (ATR/FT-IR) Spectroscopy

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3872
Author(s):  
Klytaimnistra Katsara ◽  
George Kenanakis ◽  
Zacharias Viskadourakis ◽  
Vassilis M. Papadakis
Keyword(s):  
Vibrational Spectroscopy ◽  
Food Packaging ◽  
Time Frame ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Ft Ir ◽  
Comparative Results ◽  
Short Time ◽  
And Storage ◽  
Ft Ir Spectroscopy

For multiple years, food packaging migration has been a major concern in food and health sciences. Plastics, such as polyethylene, are continuously utilized in food packaging for preservation and easy handling purposes during transportation and storage. In this work, three types of cheese, Edam, Kefalotyri and Parmesan, of different hardness were studied under two complementary vibrational spectroscopy methods, ATR-FTIR and Raman spectroscopy, to determine the migration of low-density polyethylene from plastic packaging to the surface of cheese samples. The experimental duration of this study was set to 28 days due to the degradation time of the selected cheese samples, which is clearly visible after 1 month in refrigerated conditions at 4 °C. Raman and ATR-FTIR measurements were performed at a 4–3–4–3 day pattern to obtain comparative results. Initially, consistency/repeatability measurement tests were performed on Day0 for each sample of all cheese specimens to understand if there is any overlap between the characteristic Raman and ATR-FTIR peaks of the cheese with the ones from the low-density polyethylene package. We provide evidence that on Day14, peaks of low-density polyethylene appeared due to polymeric migration in all three cheese types we tested. In all cheese samples, microbial outgrowth started to develop after Day21, as observed visually and under the bright-field microscope, causing peak reverse. Food packaging migration was validated using two different approaches of vibrational spectroscopy (Raman and FT-IR), revealing that cheese needs to be consumed within a short time frame in refrigerated conditions at 4 °C.

Physical and mechanical properties of linear low-density polyethylene/cycloolefin copolymer/layered silicate nanocomposite

2015 ◽  
Vol 37 (11) ◽  
pp. 3167-3174 ◽  
Author(s):  
S. Sánchez-Valdes ◽  
E. Ramírez-Vargas ◽  
L.F. Ramos de Valle ◽  
J.G. Martinez-Colunga ◽  
J. Romero-Garcia ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Layered Silicate ◽  
Physical And Mechanical Properties ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Linear Low Density Polyethylene
Sign in / Sign up

Export Citation Format

Share Document