scholarly journals Desain dan Realisasi Filter Bandpass Mikrostrip Dengan Struktur Hairpin

2016 ◽  
Vol 13 (1) ◽  
pp. 33
Author(s):  
Teguh Praludi ◽  
Yaya Sulaeman
Keyword(s):  
Insertion Loss ◽  
Return Loss ◽  
Design System ◽  
Advanced Design System

Kebutuhan akan sebuah filter dalam sebuah rangkaian elektronik mutlak diperlukan, dikarenakan sesuai dengan fungsi filter adalah meloloskan frekuensi yang diinginkan dan akan menahan frekuensi yang tidak diinginkan. Desain dan realisasi filter bandpass menggunakan teknologi mikrostrip dengan struktur hairpin akan dipaparkan pada makalah ini. Strukur hairpin merupakan perbaikan dari filter yang menggunakan parallel coupled bila ditinjau dari sisi dimensi sebuah filter, di mana pada struktur hairpin ini, panjang dari stripline akan dilipat membentuk huruf U sebesar ½ λ dengan sudut lekukan 90o. Filter bandpass struktur hairpin dengan teknologi mikrostrip akan didesain dengan insertion loss ≤ -3 dB pada daerah passband, return loss ≥ -20 dB, lebar bandwidth 200 MHz, impedansi karakteristik 50 Ω, frekuensi kerja 2,9–3,1 GHz dengan respon filter Chebyshev 0,1 dB. Filter bandpass yang didesain menggunakan bahan dari roger RO4350 yang mempunyai ketebalan 1,44 mm, dan permitivitas relatif (εr) = 3,77. Filter bandpass struktur hairpin ini dirancang dan disimulasikan dengan menggunakan perangkat lunak ADS (Advanced Design System) dari Agilent.

scholarly journals Design and Realization of Coupled Line Bandpass Filter Using Compact Structure at Frequencies of 3300 MHz – 3400 MHz for WiMAX Application

2016 ◽  
Vol 16 (1) ◽  
pp. 11
Author(s):  
Arief Budi Santiko ◽  
Yahya Syukri Amrullah ◽  
Yuyu Wahyu ◽  
Muhammad Ilham Maulana ◽  
Bambang Setia
Keyword(s):  
Insertion Loss ◽  
Return Loss ◽  
Bandpass Filter ◽  
Center Frequency ◽  
Design System ◽  
Compact Structure ◽  
Coupled Line ◽  
Broadband Wireless ◽  
Simulation And Optimization ◽  
Simulation Results

In this paper, the design of microstrip BPF (Bandpass Filter) for WiMAX (Worldwide Interoperability for Microwave Access) application has been presented. The frequency band allocations for BWA (Broadband Wireless Access) in Indonesia are 2.3; 3.3 and 5.8 GHz. This microtrip BPF is designed using parallel coupled line in compact form and it has spesific parameter, i.e. 3.35 GHz center frequency, 400 MHz bandwidth, VSWR ≤ 2, -3 dB insertion loss and matching impedance between two port is 50 Ω. The Advanced Design System (ADS) software has been used during simulation and optimization. The simulation results show that return loss S11 and insertion loss S21 are -15.31 dB and -2.2 dB at 3.35 GHz respectively. For the design verification, the prototype of the proposed design wasfabricated and measured.The results of the fabrication approach of simulation results, which have return loss value S11and insertion loss S21 of the proposed microstrip filter are -18.20 dB and -2.91 dB at 3.35 GHz respectively. The result shows that the proposed design can be implemented forWiMAX communication system applications

scholarly journals Band-Pass Filter Microstrip at 3 GHz Frequency Using Square Open-Loop Resonator for S-Band Radar Applications

2020 ◽  
Vol 20 (2) ◽  
pp. 53
Author(s):  
Rima Anisa Maulidini ◽  
M. Reza Hidayat ◽  
Teguh Praludi
Keyword(s):  
Insertion Loss ◽  
Return Loss ◽  
Open Loop ◽  
Center Frequency ◽  
Design System ◽  
Substrate Thickness ◽  
Band Pass Filter ◽  
Pass Filter ◽  
Measurement Results ◽  
Band Pass

In telecommunication, filters are often used to pass the desired frequency. One of them is the Band-Pass Filter (BPF) which is passing signals between the upper cut-off frequency and the lower cut-off frequency. This research aims to make a band-pass filter that can pass 3 GHz frequency with a bandwidth of 200 MHz. This filter is designed with a square open-loop resonator simulated using Advanced Design System (ADS) software. The filter is made using FR 4-epoxy substrates with a dielectric constant (ε ) of 4.6 and substrate thickness (h) of 1.6 mm. Based on the simulation results obtained in the form of a comparison graph between the response of magnitude to frequency, it shows that the value of the return loss (S 11 ) parameter of -23.549 dB, insertion loss (S 21 ) parameter value of -1.397 dB, and a slightly shifted middle frequency of 2.890 GHz. Then for the measurement results obtained a parameter value return loss (S 11 ) of -16.364 dB, parameter value insertion loss (S 21 ) of -3.561 dB with a center frequency of 3.185 GHz.

scholarly journals SIMULASI ANTENA MIKROSTRIP RECTANGULAR PATCH ARRAY EMPAT ELEMEN UNTUK PENERIMA FPV 5,8 GHZ PADA WAHANA UAV

2021 ◽  
Vol 6 (2) ◽  
Author(s):  
Ferry Ferry ◽  
Syahrial Syahrial ◽  
Hubbul Walidainy ◽  
Ahmadiar Ahmadiar
Keyword(s):  
Real Time ◽  
Loss Tangent ◽  
Return Loss ◽  
Design System ◽  
Ground Control ◽  
First Person ◽  
Rectangular Patch ◽  
Ground Control Station ◽  
Aerial Vehicle ◽  
Advanced Design System

Antena merupakan faktor utama pada sistem First Person View (FPV) untuk mentransmisi video secara real time dari Unmaned Aerial Vehicle (UAV) ke pengguna di Ground Control Station (GCS). Penelitian ini bertujuan untuk merancang antena mikrostrip rectangular patch array empat elemen menggunakan teknik pencatu Line Feed untuk penerima FPV 5,8 GHz, metode yang dipakai adalah simulasi dengan software Advanced Design System (ADS). Bahan yang digunakan Epoxy fiberglass FR4, ketebalan (h) = 1,6 mm, konstanta dielektrik (εr) = 4,5, dan Loss tangent = 0,018. Berdasarkan hasil simulasi diperoleh nilai return loss = -23,018 dB, VSWR = 1,152, gain = 9,442 dBi, bandwidth = 284 MHz serta memiliki pola radiasi directional.

Optimization of Scattering Parameters through Numerical Investigation of One-bit RF MEMS Switch over Ku, K and Ka Band

2020 ◽  
Vol 12 ◽  
Author(s):  
Pampa Debnath ◽  
Ujjwal Mondal ◽  
Arpan Deyasi
Keyword(s):  
Transmission Line ◽  
Numerical Investigation ◽  
Line Width ◽  
Insertion Loss ◽  
Return Loss ◽  
Rf Mems ◽  
Rf Mems Switch ◽  
Ka Band ◽  
Mems Switch ◽  
Overlap Area

Aim:: Computation of loss factors for one-bit RF MEMS switch over Ku, K and Ka-band for two different insulating substrates. Objective:: Numerical investigation of return loss, insertion loss, isolation loss are computed under both actuated and unactuated states for two different insulating substrates of the 1-bit RF MEMS switch, and corresponding up and down-capacitances are obtained. Methods:: The unique characteristics of a 1-bit RF MEMS switch of providing higher return loss under both actuated and unactuated states and also of isolation loss with negligible insertion loss makes it as a prime candidate for phase shifter application. This is presented in this manuscript with a keen focus on improvement capability by changing transmission line width, and also of overlap area; where dielectric constant of the substrate also plays a vital role. Results:: The present work exhibits very low down-capacitance over the spectrum whereas considerable amount of up-capacitance. Also when overall performance in terms of all loss parameters are considered, switch provides very low insertion loss, good return loss under actuated state and standard isolation loss. Conclusion:: Reduction of transmission line width of about 33% improved the performance of the switch by increasing isolation loss. Isolation loss of -40 dB is obtained at actuated condition in higher microwave spectra for SiO 2 at higher overlap area. Down capacitance of ~ 1dB is obtained which is novel as compared with other published literature. Moreover, a better combination of both return loss, isolation loss and insertion loss are reported in this present work compared with all other published data so far.

Computer-Aided Analysis and Measurement of an Interconnection System

2011 ◽  
Vol 308-310 ◽  
pp. 2279-2285
Author(s):  
Wei Chen Lee ◽  
Hill Wu
Keyword(s):  
Simulation Model ◽  
Frequency Domain ◽  
Insertion Loss ◽  
Return Loss ◽  
Design Phase ◽  
Electrical Characteristics ◽  
Impedance Mismatch ◽  
Measurement Results ◽  
Computer Aided Analysis ◽  
Computer Aided

The electrical characteristics of an interconnection system, which include impedance, insertion loss, and return loss, can greatly affect its performance as the signal speed increases. The objective of this research was to understand the discrepancy between the computer-aided analysis and measurement results of an interconnection system, so that a more accurate prediction of the electrical characteristics of this system can be made during the design phase. It was discovered that in both the time and frequency domain the computer-aided analysis results were consistent with the measurement results. Given these conclusions the simulation model was modified to improve the impedance mismatch within the interconnection system. It was found that by properly designing the antipad, the impedance mismatch can be greatly reduced.

A dual-band crossover using cross-shaped microstrip line for small and large band ratios

2017 ◽  
Vol 9 (8) ◽  
pp. 1629-1635 ◽  
Author(s):  
Idury Satya Krishna ◽  
Rusan Kumar Barik ◽  
S. S. Karthikeyan
Keyword(s):  
Insertion Loss ◽  
Matrix Method ◽  
Microstrip Line ◽  
Return Loss ◽  
Dual Band ◽  
Band Ratios ◽  
Form Design ◽  
Frequency Ratios ◽  
Novel Design ◽  
Large Frequency

A novel design of planar dual-band microstrip crossover operating at small and large frequency ratios is presented. These features of the proposed dual-band crossover are achieved by a cross-shaped transmission line. To obtain the dual-band characteristics, the required closed form design formulas are computed using the ABCD matrix method. Based on the design formulas, the realizable small and large band ratios are calculated as 1.65–2.14 and 4.1–8.76, respectively. To validate the computed band ratios, three examples of dual-band crossovers are presented. Finally, two prototypes of dual-band crossover working at smaller and larger frequency ratios are fabricated and tested. The fabricated dual-band crossovers exhibit good return loss and isolation of over 20 dB with minimal insertion loss.

scholarly journals Sharp Skirt Dual-Mode Bandpass Filter with Overlay Plate to Control Upper Passband Edge

2019 ◽  
Vol 8 (6) ◽  
pp. 2357-2360
Keyword(s):  
Analytical Model ◽  
Insertion Loss ◽  
Return Loss ◽  
Bandpass Filter ◽  
Center Frequency ◽  
Dual Mode ◽  
Rf Receivers ◽  
Attenuation Level ◽  
Frequency Selective ◽  
Fixed Center

This paper presents design and analytical model for Sharp Skirt Dual-Mode Bandpass Filter for RF receivers. Proposed filter is designed using open stub loaded H shaped resonator. Based on analytical model insertion loss S21 and return loss S11 for proposed filter are demonstrated. Inductive Overlaying plate is proposed to control upper passband edge of proposed filter to improve frequency selectivity with fixed center frequency. The proposed filter has sharp frequency selective range from 5.1GHz to 9.2GHz. With overlay plate, frequency selective range is tuned to 5.1GHz-8.6GHz. Without overlaying plate the proposed filter has return loss greater than 10dB and insertion loss of 0.7dB. Lower and upper passband edges are at 5.1GHz and 9.2GHz with attenuation level of 52dB and 54dB respectively. With overlaying plate, the filter has same S 11 and S 21 parameters, but upper passband edge is shifted from 9.2GHz to 8.6GHz

scholarly journals Design and Realization of Band Pass Filter in K-Band Frequency for Short Range Radar Application

2021 ◽  
Vol 21 (1) ◽  
pp. 1
Author(s):  
Arie Setiawan ◽  
Taufiqqurrachman Taufiqqurrachman ◽  
Adam Kusumah Firdaus ◽  
Fajri Darwis ◽  
Aminuddin Rizal ◽  
...  
Keyword(s):  
Insertion Loss ◽  
Short Range ◽  
Return Loss ◽  
Band Pass Filter ◽  
Pass Filter ◽  
Band Frequency ◽  
Measurement Results ◽  
Band Pass ◽  
Bandwidth Analysis ◽  
K Band

Short range radar (SRR) uses the K-band frequency range in its application. The radar requires high-resolution, so the applied frequency is 1 GHz wide. The filter is one of the devices used to ensure only a predetermined frequency is received by the radar system. This device must have a wide operating bandwidth to meet the specification of the radar. In this paper, a band pass filter (BPF) is proposed. It is designed and fabricated on RO4003C substrate using the substrate integrated waveguide (SIW) technique, results in a wide bandwidth at the K-band frequency that centered at 24 GHz. Besides the bandwidth analysis, the analysis of the insertion loss, the return loss, and the dimension are also reported. The simulated results of the bandpass filter are: VSWR of 1.0308, a return loss of -36.9344 dB, and an insertion loss of -0.6695 dB. The measurement results show that the design obtains a VSWR of 2.067, a return loss of -8.136 dB, and an insertion loss of -4.316  dB. While, it is obtained that the bandwidth is reduced by about 50% compared with the simulation. The result differences between simulation and measurement are mainly due to the imperfect fabrication process.

scholarly journals Directivity Enhancement in Non-Reciprocal Bandpass Filters using an Evolutionary Algorithm

2021 ◽  
Author(s):  
Prantik Dutta ◽  
Arun Gande ◽  
Gopi Ram
Keyword(s):  
Evolutionary Algorithm ◽  
Insertion Loss ◽  
Return Loss ◽  
Bandpass Filter ◽  
Trial And Error ◽  
Swarm Optimization ◽  
Lumped Element ◽  
Trial And Error Method ◽  
Error Method ◽  
Maximum Directivity

In this letter, a non-reciprocal filter with enhanced directivity is analyzed methodically and the filter parameters are optimized using an evolutionary algorithm. The return loss, insertion loss, and isolation characteristics of the filter exhibit a trade-off that makes manual tuning a trial-and-error method. The veracity of the numerical modeling is conformed by designing a 150 MHz lumped element non-reciprocal bandpass filter based on the parameters extracted using an evolutionary algorithm based particle swarm optimization (PSO). The simulated and measured results comply well with the modeling and the results exhibit maximum directivity of 28.2 dB without degradation in insertion loss (1.1 dB) and return loss (16.2 dB) within the passband. The algorithm can be utilized in designing non-reciprocal filters having different center frequencies and bandwidths.

Sign in / Sign up

Export Citation Format

Share Document