scholarly journals JATROPHA OIL WITH IRON NANOPARTICLES APPLICATION IN DRILLING PROCESSES

2019 ◽  
Vol 59 (3) ◽  
pp. 299-304
Author(s):  
Veikko Shalimba ◽  
Vít Sopko
Keyword(s):  
Heat Transfer ◽  
High Performance ◽  
Iron Nanoparticles ◽  
Volume Fraction ◽  
Volume Ratio ◽  
Heat Transfer Fluid ◽  
Nanoparticle Volume Fraction ◽  
Jatropha Oil ◽  
Heat Transfer Fluids ◽  
Performance Of Heat Transfer

A performance of heat transfer fluids has a substantial influence on the size, weight and cost of heat transfer systems, therefore, a high-performance heat transfer fluid is very important in many industries. Over the last decades, nanofluids have been developed. According to many researchers and publications on nanofluids, it is evident that nanofluids have a high thermal conductivity. The aim of this experimental study was to investigate the change of the workpiece temperature during drilling using Jatropha oil with iron nanoparticles and water with iron nanoparticles as lubricating and cooling fluids. These experiments were carried out with samples of nanofluid with different nanoparticles volume ratio, such as samples JN1, JN5 and JN10 of iron nanoparticles in the base Jatropha oil with a nanoparticle volume fraction of 1 %, 5% and 10% respectively and samples WN1, WN5 and WN10 of iron nanoparticles in the base water with a nanoparticle volume fraction of 1 %, 5% and 10% respectively.

A Brief Review on Thermal Behaviour of PANI as Additive in Heat Transfer Fluid

2021 ◽  
Vol 02 (01) ◽  
Author(s):  
A.G.N. Sofiah ◽  
◽  
M. Samykano ◽  
S. Shahabuddin ◽  
K. Kadirgama ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Thermal Properties ◽  
Conducting Polymers ◽  
Volume Fraction ◽  
Corrosion Property ◽  
Environmental Stability ◽  
Heat Transfer Fluid ◽  
Thermal Engineering ◽  
Engineering System ◽  
Heat Transfer Fluids

Since a decade ago, investigation on nanofluids has grown significantly owing to its enhanced thermal properties compared to conventional heat transfer fluids. This engineered nanofluid has been widely used in the thermal engineering system to improve their energy consumption by improving the thermal efficiency of the system. The addition of nano-size particles as additives dispersed in the base fluids proved to significantly either improve or diminish the behaviour of the base fluids. The behaviour of the base fluid highly depends on the properties of the additives material, such as morphology, size, and volume fraction. Among the variety of nanoparticles studied, the conducting polymers have been subject of high interest due to its high environmental stability, good electrical conductivity, antimicrobial, anti-corrosion property and significantly cheap compared to other nanoparticles. As such, the main objective of the present review is to provide an overview of the work performed on thermal properties performance of conducting polymers based nanofluids.

scholarly journals Thermal performance evaluation of hot oils and nanofluids by simulation of an indirect heating plant

2020 ◽  
pp. 23-23
Author(s):  
Lis Ostigard ◽  
Silvana Mattedi
Keyword(s):  
Heat Transfer ◽  
Thermal Performance ◽  
Volume Fraction ◽  
Heat Transfer Fluid ◽  
Diphenyl Oxide ◽  
Heat Transfer Fluids ◽  
Industrial Unit ◽  
Lower Heat ◽  
Fractionation Plant ◽  
Heating Plant

This paper aims to analyze the thermal performance of four different heat transfer fluids in a hot oil system located in a paraffin hydrotreatment and fractionation plant of a petroleum refinery. The software Petro-SIM? (KBC-Yokogawa) was employed to elaborate steady-state simulations intended to compare the heat transfer fluid currently used (eutectic of biphenyl and diphenyl oxide) and three fluids proposed as substitutes: paraffin oil (namely n-C13+) produced in the very industrial unit, a nanofluid of eutectic of biphenyl and diphenyl oxide and copper at a 6 % volume fraction, and a CuO/polydimethylsiloxane nanofluid at a 6 % volume fraction. The results showed that n-C13+ was the only heat transfer fluid that could replace the eutectic diphenyl oxide/ biphenyl in the system under analysis since it absorbed the heat duty of 13.79 Gcal/ h, which exceeded the thermal energy of 10.57 Gcal/ h absorbed by the heat transfer fluid currently used at the same operating parameters. The Cu/ eutectic of biphenyl and diphenyl oxide and CuO/polydimethylsiloxane nanofluids presented lower heat duty than the energy needed for the operation of the hot oil system, which was 8.31 Gcal/h and 8.51 Gcal/h, respectively.

scholarly journals Performance of Graphite-Dispersed Li2CO3-K2CO3 Molten Salt Nanofluid for a Direct Absorption Solar Collector System

Molecules ◽  
2020 ◽  
Vol 25 (2) ◽  
pp. 375 ◽  
Author(s):  
M. A. Karim ◽  
Majedul Islam ◽  
Owen Arthur ◽  
Prasad KDV Yarlagadda
Keyword(s):  
Heat Transfer ◽  
Molten Salt ◽  
Solar Collector ◽  
Volume Fraction ◽  
Heat Transfer Fluid ◽  
Total Efficiency ◽  
Nanoparticle Volume Fraction ◽  
Direct Absorption ◽  
Solar Salt ◽  
Direct Absorption Solar Collector

Considered to be the next generation of heat transfer fluids (HTFs), nanofluids have been receiving a growing interest over the past decade. Molten salt nanofluids have been shown to have great potential as an HTF for use in high temperature applications such as direct absorption solar collector (DAC) system. Very few studies using molten salt nanofluids as the HTF in a DAC receiver can be found in the open literature. This study aimed to develop a 3D computational fluid dynamics model of the receiver of a DAC using graphite-nanoparticle-dispersed Li2CO3-K2CO3 molten salt nanofluid to investigate the effects of design and operation parameters on receiver performance. Receiver total efficiency using Li2CO3-K2CO3 salt was compared with that using solar salt nanofluid. Spectral properties of the base fluid and nanoparticles were modeled as wavelength-dependent and the absorption of the solar radiation was modeled as a volumetric heat release in the flowing heat transfer fluid. Initial results show that the receiver efficiency increases with increasing solar concentration, decreasing nanoparticle volume fraction, and decreasing receiver length. It was also found that the Carnot efficiency increases with increasing receiver length and nanoparticle volume fraction, and decreasing solar concentration and inlet velocity. Comparative study shows that solar salt HTF could provide higher total efficiency. However, a higher operating temperature of Li2CO3-K2CO3 will allow for a greater amount of thermal energy storage for a smaller volume of liquid.

scholarly journals Numerical Evaluation of a HVAC System Based on a High-Performance Heat Transfer Fluid

Energies ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3298
Author(s):  
Gianpiero Colangelo ◽  
Brenda Raho ◽  
Marco Milanese ◽  
Arturo de Risi
Keyword(s):  
Heat Transfer ◽  
High Performance ◽  
Cooling System ◽  
Electrical Energy ◽  
Simulation Software ◽  
Heat Transfer Fluid ◽  
Hvac System ◽  
Dynamic Simulations ◽  
Heating And Cooling ◽  
The University

Nanofluids have great potential to improve the heat transfer properties of liquids, as demonstrated by recent studies. This paper presents a novel idea of utilizing nanofluid. It analyzes the performance of a HVAC (Heating Ventilation Air Conditioning) system using a high-performance heat transfer fluid (water-glycol nanofluid with nanoparticles of Al2O3), in the university campus of Lecce, Italy. The work describes the dynamic model of the building and its heating and cooling system, realized through the simulation software TRNSYS 17. The use of heat transfer fluid inseminated by nanoparticles in a real HVAC system is an innovative application that is difficult to find in the scientific literature so far. This work focuses on comparing the efficiency of the system working with a traditional water-glycol mixture with the same system that uses Al2O3-nanofluid. The results obtained by means of the dynamic simulations have confirmed what theoretically assumed, indicating the working conditions of the HVAC system that lead to lower operating costs and higher COP and EER, guaranteeing the optimal conditions of thermo-hygrometric comfort inside the building. Finally, the results showed that the use of a nanofluid based on water-glycol mixture and alumina increases the efficiency about 10% and at the same time reduces the electrical energy consumption of the HVAC system.

scholarly journals Contribution to the Parametric Study of the Performance of A Parabolic Trough Collector

2021 ◽  
Vol 321 ◽  
pp. 02016
Author(s):  
Belkacem Bouali ◽  
Hanane-Maria Regue
Keyword(s):  
Heat Transfer ◽  
Mass Flow ◽  
Flow Rate ◽  
Optimal Operation ◽  
Heat Transfer Fluid ◽  
Parabolic Trough ◽  
Parabolic Trough Collector ◽  
Heat Transfer Fluids ◽  
Ansys Cfx ◽  
Different Seasons

This paper presents an analysis of the performance of a parabolic trough collector (PTC) according to some key operating parameters. The effects of the secondary reflector, the length and thickness of the absorber tube (receiver tube) and the flow rate of the heat transfer fluid (HTF) are investigated. The main objective is to determine an optimal operation, which improves the performance of a traditional PTC. The target variables are the temperature at the outlet of the tube, the amount of energy collected by the HTF and the efficiency of the system. The solar flux data concern the city of LAGHOUAT located in the south of Algeria. Four days in different seasons are considered. The optical analysis of the system is performed by using the open source SolTrace code. The output of this analysis is used as a boundary condition for the CFD solver. The conjugate heat transfer and the fluid flow through the absorber tube are simulated by using ANSYS-CFX solver. Water is considered as heat transfer fluids. The obtained results show that the use of a curved secondary reflector significantly improves the performance of the traditional PTC. As the thickness of the tube increases, the heat storage in the material increases, which increases the temperature at the exit of the tube and therefore the efficiency of the system. However, the length of the tube depends on the mass flow of the HTF and vice versa. To keep the efficiency constant by choosing another length, it is necessary to choose a mass flow rate proportional to the flow rate corresponding to the initial length.

Performance of heat transfer fluids with nanographene in a pilot solar collector

Solar Energy ◽  
2018 ◽  
Vol 172 ◽  
pp. 171-176 ◽  
Author(s):  
F.E.B. Bioucas ◽  
S.I.C. Vieira ◽  
M.J.V. Lourenço ◽  
F.J.V. Santos ◽  
C.A. Nieto de Castro
Keyword(s):  
Heat Transfer ◽  
Solar Collector ◽  
Heat Transfer Fluids ◽  
Performance Of Heat Transfer

Thermodynamic Analysis of Heat and Fluid Flow in a Microchannel With Internal Fins

2009 ◽  
Author(s):  
Ramesh Narayanaswamy ◽  
Tilak T. Chandratilleke ◽  
Andrew J. L. Foong
Keyword(s):  
Heat Transfer ◽  
Fluid Flow ◽  
Thermodynamic Analysis ◽  
Entropy Generation ◽  
High Performance ◽  
Numerical Study ◽  
Three Dimensional ◽  
Heat Sinks ◽  
Heat Transfer Fluid ◽  
Internal Fins

Efficient cooling techniques are one of the critical design requirements for maintaining reliable operational characteristics of modern, miniaturised high performance electronic components. Microchannel heat sinks form an integral part of most devices used for thermal management in electronic equipment cooling. A microchannel of square cross section, having internal longitudinal fins is considered for analysis. A numerical study is carried out to investigate the fluid flow and heat transfer characteristics. Three-dimensional numerical simulations are performed on the microchannel in the presence of a hydrodynamically developed, thermally developing laminar flow. Further on, a thermodynamic analysis is carried out, for a range of fin heights and thermophysical parameters, in order to obtain the irreversibilities due to heat transfer and fluid flow within the microchannel. An optimum fin height, corresponding to the thermodynamically optimum conditions that minimize the entropy generation rates has been obtained. The effect of the presence of internal fins on the entropy generated due to heat transfer, fluid friction, and the total entropy generation is also provided.

scholarly journals Flow and Heat Transfer of Cu-Water Nanofluid between a Stretching Sheet and a Porous Surface in a Rotating System

2012 ◽  
Vol 2012 ◽  
pp. 1-18 ◽  
Author(s):  
M. Sheikholeslami ◽  
H. R. Ashorynejad ◽  
G. Domairry ◽  
I. Hashim
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Base Fluid ◽  
Stretching Sheet ◽  
Volume Fraction ◽  
Rotation Parameter ◽  
Nanoparticle Volume Fraction ◽  
Heat Transfer Characteristics ◽  
Rotating System ◽  
Flow And Heat Transfer

The aim of the present paper is to study the flow of nanofluid and heat transfer characteristics between two horizontal plates in a rotating system. The lower plate is a stretching sheet and the upper one is a solid porous plate. Copper (Cu) as nanoparticle and water as its base fluid have been considered. The governing partial differential equations with the corresponding boundary conditions are reduced to a set of ordinary differential equations with the appropriate boundary conditions using similarity transformation, which is then solved analytically using the homotopy analysis method (HAM). Comparison between HAM and numerical solutions results showed an excellent agreement. The results for the flow and heat transfer characteristics are obtained for various values of the nanoparticle volume fraction, suction/injection parameter, rotation parameter, and Reynolds number. It is shown that the inclusion of a nanoparticle into the base fluid of this problem is capable of causing change in the flow pattern. It is found that for both suction and injection, the heat transfer rate at the surface increases with increasing the nanoparticle volume fraction, Reynolds number, and injection/suction parameter and it decreases with power of rotation parameter.

scholarly journals Heat transfer studies of Al2O3/water-ethylene glycol nanofluid using factorial design analysis

2021 ◽  
pp. 21-21
Author(s):  
Srinivasan Manikandan ◽  
Nesakumar Dharmakkan ◽  
Nagamani Sumana
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Ethylene Glycol ◽  
Transfer Coefficient ◽  
Heat Input ◽  
Base Fluid ◽  
Volume Fraction ◽  
Nanoparticle Volume Fraction ◽  
Experimental Heat ◽  
Fluid Concentration

The experimental study of heat transfer coefficient of nanofluid plays a significant role in improving the heat transfer rate of the heat exchanger. The research was conducted in a natural convection heat transfer apparatus by suspending Al2O3 nanoparticle in a base fluid of Water-Ethylene glycol mixture. The effects of heat input (A), nanoparticle volume fraction (B), and base fluid concentration (C) on experimental heat transfer coefficient (hexpnf) were studied. By the results obtained by MINITDesign software 23 full factorial design matrix, 16 experimental runs were performed with the lower and higher level of input factors. The levels for heat input are 10 and 100 W; nanoparticle volume fraction is 0.1 and 1 volume% and for base fluid concentration is 30 and 50 volume% of Ethylene Glycol in water. From the obtained experimental results residual plots, Pareto chart, contour plot and 3D surface plots were drawn. It can be found from the study that the experimental heat transfer coefficient showed highest enhancement with high level of nanoparticle volume fraction and moderate enhancement with high level of heat input and slight enhancement with base fluid concentration.

Sign in / Sign up

Export Citation Format

Share Document