scholarly journals THE EFFECT OF MICRO-SILICA ON THE MICROSCOPIC FEATURES OF THE UHPC COMPOSITE AND ITS INTER-FACIAL TRANSITION ZONE

2018 ◽  
Vol 15 ◽  
pp. 31-35 ◽  
Author(s):  
Vladimír Hrbek ◽  
Zdeněk Prošek ◽  
Roman Chylík ◽  
Lukáš Vráblík
Keyword(s):  
Transition Zone ◽  
High Performance ◽  
Mechanical Performance ◽  
High Performance Concrete ◽  
Ultra High Performance Concrete ◽  
Microscopic Features ◽  
Cement Binder ◽  
Micro Silica ◽  
The Impact ◽  
Silica Additive

The uplift of concrete overall macroscopic performance by way of alternative additives is commonly used technique. In case of ultra high performance concrete (UHPC), micro-silica is added to the mixture as a micro-filler to the structure of cement binder. As a result, the cementitious matrix macro-mechanical performance is elevated. This paper is aimed on the UHPC micro-scale enhancement by different micro-silica additive content in the mixture. More closely, the study investigate the impact of the micro-silica on the inter-facial transition zone (ITZ) between the binder matrix and basaltic aggregate.

SUSTAINABLE ULTRA-HIGH-PERFORMANCE GLASS CONCRETE FOR INFRASTRUCTURES

2017 ◽  
Vol 4 (1) ◽  
Author(s):  
Arezki Tagnit-Hamou ◽  
Nancy A. Soliman
Keyword(s):  
High Performance ◽  
Glass Powder ◽  
Mechanical Performance ◽  
High Performance Concrete ◽  
Low Cost ◽  
Research Work ◽  
High Strength ◽  
Quartz Powder ◽  
Ultra High Performance Concrete ◽  
Powder Particles

This paper presents research work on the development of a green type of ultra-high-performance concrete using ground glass powders with different degrees of fineness (UHPGC). This article presents the development of an innovative, low-cost, and sustainable UHPGC through the use of glass powder to replace cement, and quartz powder particles. An UHPGC with a compressive strength (fc) of up to 220 MPa was prepared and its fresh, and mechanical properties were investigated. The test results indicate that the fresh UHPGC properties were improved when the cement and quartz powder were replaced with non-absorptive glass powder particles. The strength improvement can be attributed to the glass powder’s pozzolanicity and to its mechanical performance (very high strength and elastic modulus of glass). A case study of using this UHPGC is presented through the design and construction of a footbridge. Erection of footbridge at University of Sherbrooke Campus using UHPGC is also presented as a full-scale application.

scholarly journals Production of Ultra-High-Performance Concrete with Low Energy Consumption and Carbon Footprint Using Supplementary Cementitious Materials Instead of Silica Fume: A Review

Energies ◽  
2021 ◽  
Vol 14 (24) ◽  
pp. 8291
Author(s):  
Mays A. Hamad ◽  
Mohammed Nasr ◽  
Ali Shubbar ◽  
Zainab Al-Khafaji ◽  
Zainab Al Masoodi ◽  
...  
Keyword(s):  
Energy Consumption ◽  
Silica Fume ◽  
High Performance ◽  
High Performance Concrete ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Ultra High Performance Concrete ◽  
Cement Production ◽  
Granulated Blast Furnace Slag ◽  
The Impact

The increase in cement production as a result of growing demand in the construction sector means an increase in energy consumption and CO2 emissions. These emissions are estimated at 7% of the global production of CO2. Ultra-high-performance concrete (UHPC) has excellent mechanical and durability characteristics. Nevertheless, it is costly and affects the environment due to its high amount of cement, which may reach 800–1000 kg/m3. In order to reduce the cement content, silica fume (SF) was utilized as a partial alternative to cement in the production of UHPC. Nevertheless, SF is very expensive. Therefore, the researchers investigated the use of supplementary cementitious materials cheaper than SF. Very limited review investigates addressed the impact of such materials on different properties of UHPC in comparison to that of SF. Thus, this study aims to summarize the effectiveness of using some common supplementary cementitious materials, including fly ashes (FA), ground granulated blast furnace slag (GGBS), metakaolin (MK) and rice husk ashes (RHA) in the manufacturing of UHPC, and comparing the performance of each material with that of SF. The comparison among these substances was also discussed. It has been found that RHA is considered a successful alternative to SF to produce UHPC with similar or even higher properties than SF. Moreover, FA, GGBS and MK can be utilized in combination with SF (as a partial substitute of SF) as a result of having less pozzolanic activity than SF.

scholarly journals Mechanical Performance and Microstructure of Ultra-High-Performance Concrete Modified by Calcium Sulfoaluminate Cement

2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Meimei Song ◽  
Chuanlin Wang ◽  
Ying Cui ◽  
Qiu Li ◽  
Zhiyang Gao
Keyword(s):  
Compressive Strength ◽  
High Performance ◽  
Mechanical Performance ◽  
High Performance Concrete ◽  
Autogenous Shrinkage ◽  
Ultra High Performance Concrete ◽  
Maximum Heat ◽  
Degree Of Hydration ◽  
Calcium Sulfoaluminate ◽  
Shrinkage Property

High autogenous shrinkage property is one of the disadvantages of ultra-high-performance concrete (UHPC), which may induce early age cracking and threaten the safety of concrete structure. In the present study, different dosages of calcium sulfoaluminate (CSA) cement were added in UHPC as an effective expansive binder. Hydration mechanism, autogenous shrinkage property, and compressive strength of UHPC were carried out to investigate the effect of CSA addition on the mechanical properties of UHPC. Scanning electron microscopy was also employed to characterize the intrinsic microstructural reasons relating to the changes in macroproperties. Based on the XRD diagram, increasing formation of ettringite and Ca(OH)2 can be found with increasing CSA content up to 15%. In the heat flow results of UHPC with 10% CSA addition, the maximum heat release increases to 2.6 mW/g, which is 8.3% higher than the reference UHPC, suggesting a higher degree of hydration with CSA addition. The results in autogenous shrinkage show that CSA expansion agent plays a significantly beneficial role in improving the autogenous shrinkage of UHPC. The corresponding autogenous shrinkage of UHPC is −59.66 μ ε , −131.11 μ ε , and −182.31 μ ε , respectively, at 7 d with 5%, 10%, and 15% addition, which is 108%, 117%, and 123% reduction compared to the reference specimen without CSA. In terms of compressive strength, UHPC with 5%, 10%, 15%, and 20% CSA addition has 10.5%, 17.4%, 30.2%, and 22.1% higher compressive strength than that for the reference UHPC at 28 d. Microstructural study shows that there is an extremely dense microstructure in both the bulk matrix and interfacial transition zone of UHPC with 10% CSA addition, which can be attributed to the higher autogenous shrinkage property and can therefore result in higher mechanical performance.

Ultra-High-Performance Concrete Shear Keys in Concrete Bridge Superstructures

2020 ◽  
pp. 036119812096472
Author(s):  
Elsy Y. Flores ◽  
Jordan Varbel ◽  
William K. Toledo ◽  
Craig M. Newtson ◽  
Brad D. Weldon
Keyword(s):  
High Performance ◽  
Load Transfer ◽  
Mechanical Performance ◽  
High Performance Concrete ◽  
Surface Preparation ◽  
Ultra High Performance Concrete ◽  
Direct Tension ◽  
Girder Bridges ◽  
Grouting Material ◽  
Shear Keys

This research investigated the use of locally produced, non-proprietary ultra-high-performance concrete (UHPC) as a grouting material to repair deteriorated shear keys. Shear keys are used in adjacent girder superstructures to produce monolithic behavior and load transfer across the structure. Shear key degradation can jeopardize the integrity of the structure. Transportation agencies have reported that 75% of distress in adjacent girder bridges is because of cracking and de-bonding along shear keys. Previous research has shown that locally produced UHPC has excellent mechanical and durability properties. UHPC has also been shown to have good bonding characteristics that are desirable in a potential grouting material. Bond strength between UHPC grout and substrate concrete was evaluated using slant-shear and direct tension tests. Results showed that adequate bond was achieved at 7 days. Low strengths at 28 days were observed because of low strength of the substrate concrete. Shrinkage of UHPC grout was also investigated. Shrinkage at 28 days was less than 600 µstrain which is acceptable for repair practices. Full-scale testing was used to evaluate load-deflection behavior of channel girder assemblages with grouted shear keys. Results showed that UHPC grout and non-shrink grout had similar mechanical performance. Excellent bond was achieved with all grouts, even with minimal surface preparation. The similar performances of the non-shrink grout and the UHPC grout indicates that UHPC grout does not provide a mechanical benefit over the non-shrink grout.

Sign in / Sign up

Export Citation Format

Share Document