Mechanical performance of affordable and eco-efficient ultra-high performance concrete (UHPC) containing recycled tyre steel fibres

2020 ◽  
Vol 255 ◽  
pp. 119272
Author(s):  
M.N. Isa ◽  
Kypros Pilakoutas ◽  
Maurizio Guadagnini ◽  
Harris Angelakopoulos
Keyword(s):  
High Performance ◽  
Mechanical Performance ◽  
High Performance Concrete ◽  
Ultra High Performance Concrete ◽  
Steel Fibres

Design of an Experimental Prestressed Vierendeel Pedestrian Bridge Made of UHPC

2014 ◽  
Vol 587-589 ◽  
pp. 1642-1645 ◽  
Author(s):  
Petr Tej ◽  
Alena Tejová
Keyword(s):  
High Performance ◽  
High Performance Concrete ◽  
Total Width ◽  
Bridge Structure ◽  
Ultra High Performance Concrete ◽  
Pedestrian Bridge ◽  
Main Structure ◽  
Steel Fibres

This paper presents the design of an experimental prestressed Vierendeel pedestrian bridge made of ultra-high performance concrete (UHPC). The structure is designed as a permanent single-span bridge with an intermediate deck. The span of the bridge structure is 61.38 m, the total width is 6.68 m, and the clearance width of the bridge is 5.30 m. The main structure of the bridge consists of two prestressed Vierendeel beams made of UHPC with dispersed steel fibres . The main beams are composed of prefabricated parts, subsequently prestressed.

SUSTAINABLE ULTRA-HIGH-PERFORMANCE GLASS CONCRETE FOR INFRASTRUCTURES

2017 ◽  
Vol 4 (1) ◽  
Author(s):  
Arezki Tagnit-Hamou ◽  
Nancy A. Soliman
Keyword(s):  
High Performance ◽  
Glass Powder ◽  
Mechanical Performance ◽  
High Performance Concrete ◽  
Low Cost ◽  
Research Work ◽  
High Strength ◽  
Quartz Powder ◽  
Ultra High Performance Concrete ◽  
Powder Particles

This paper presents research work on the development of a green type of ultra-high-performance concrete using ground glass powders with different degrees of fineness (UHPGC). This article presents the development of an innovative, low-cost, and sustainable UHPGC through the use of glass powder to replace cement, and quartz powder particles. An UHPGC with a compressive strength (fc) of up to 220 MPa was prepared and its fresh, and mechanical properties were investigated. The test results indicate that the fresh UHPGC properties were improved when the cement and quartz powder were replaced with non-absorptive glass powder particles. The strength improvement can be attributed to the glass powder’s pozzolanicity and to its mechanical performance (very high strength and elastic modulus of glass). A case study of using this UHPGC is presented through the design and construction of a footbridge. Erection of footbridge at University of Sherbrooke Campus using UHPGC is also presented as a full-scale application.

scholarly journals Mechanical Performance and Microstructure of Ultra-High-Performance Concrete Modified by Calcium Sulfoaluminate Cement

2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Meimei Song ◽  
Chuanlin Wang ◽  
Ying Cui ◽  
Qiu Li ◽  
Zhiyang Gao
Keyword(s):  
Compressive Strength ◽  
High Performance ◽  
Mechanical Performance ◽  
High Performance Concrete ◽  
Autogenous Shrinkage ◽  
Ultra High Performance Concrete ◽  
Maximum Heat ◽  
Degree Of Hydration ◽  
Calcium Sulfoaluminate ◽  
Shrinkage Property

High autogenous shrinkage property is one of the disadvantages of ultra-high-performance concrete (UHPC), which may induce early age cracking and threaten the safety of concrete structure. In the present study, different dosages of calcium sulfoaluminate (CSA) cement were added in UHPC as an effective expansive binder. Hydration mechanism, autogenous shrinkage property, and compressive strength of UHPC were carried out to investigate the effect of CSA addition on the mechanical properties of UHPC. Scanning electron microscopy was also employed to characterize the intrinsic microstructural reasons relating to the changes in macroproperties. Based on the XRD diagram, increasing formation of ettringite and Ca(OH)2 can be found with increasing CSA content up to 15%. In the heat flow results of UHPC with 10% CSA addition, the maximum heat release increases to 2.6 mW/g, which is 8.3% higher than the reference UHPC, suggesting a higher degree of hydration with CSA addition. The results in autogenous shrinkage show that CSA expansion agent plays a significantly beneficial role in improving the autogenous shrinkage of UHPC. The corresponding autogenous shrinkage of UHPC is −59.66 μ ε , −131.11 μ ε , and −182.31 μ ε , respectively, at 7 d with 5%, 10%, and 15% addition, which is 108%, 117%, and 123% reduction compared to the reference specimen without CSA. In terms of compressive strength, UHPC with 5%, 10%, 15%, and 20% CSA addition has 10.5%, 17.4%, 30.2%, and 22.1% higher compressive strength than that for the reference UHPC at 28 d. Microstructural study shows that there is an extremely dense microstructure in both the bulk matrix and interfacial transition zone of UHPC with 10% CSA addition, which can be attributed to the higher autogenous shrinkage property and can therefore result in higher mechanical performance.

Ultra-High-Performance Concrete Shear Keys in Concrete Bridge Superstructures

2020 ◽  
pp. 036119812096472
Author(s):  
Elsy Y. Flores ◽  
Jordan Varbel ◽  
William K. Toledo ◽  
Craig M. Newtson ◽  
Brad D. Weldon
Keyword(s):  
High Performance ◽  
Load Transfer ◽  
Mechanical Performance ◽  
High Performance Concrete ◽  
Surface Preparation ◽  
Ultra High Performance Concrete ◽  
Direct Tension ◽  
Girder Bridges ◽  
Grouting Material ◽  
Shear Keys

This research investigated the use of locally produced, non-proprietary ultra-high-performance concrete (UHPC) as a grouting material to repair deteriorated shear keys. Shear keys are used in adjacent girder superstructures to produce monolithic behavior and load transfer across the structure. Shear key degradation can jeopardize the integrity of the structure. Transportation agencies have reported that 75% of distress in adjacent girder bridges is because of cracking and de-bonding along shear keys. Previous research has shown that locally produced UHPC has excellent mechanical and durability properties. UHPC has also been shown to have good bonding characteristics that are desirable in a potential grouting material. Bond strength between UHPC grout and substrate concrete was evaluated using slant-shear and direct tension tests. Results showed that adequate bond was achieved at 7 days. Low strengths at 28 days were observed because of low strength of the substrate concrete. Shrinkage of UHPC grout was also investigated. Shrinkage at 28 days was less than 600 µstrain which is acceptable for repair practices. Full-scale testing was used to evaluate load-deflection behavior of channel girder assemblages with grouted shear keys. Results showed that UHPC grout and non-shrink grout had similar mechanical performance. Excellent bond was achieved with all grouts, even with minimal surface preparation. The similar performances of the non-shrink grout and the UHPC grout indicates that UHPC grout does not provide a mechanical benefit over the non-shrink grout.

scholarly journals Effect of Casting Position on Mechanical Performance of Ultra-High Performance Concrete

Materials ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 404
Author(s):  
Sujing Zhao ◽  
Yiheng Bo
Keyword(s):  
Flexural Strength ◽  
High Performance ◽  
Mechanical Performance ◽  
High Performance Concrete ◽  
Fiber Type ◽  
Peak Load ◽  
Load Ratio ◽  
Fiber Types ◽  
Ultra High Performance Concrete ◽  
Fracture Properties

The mechanical performance of ultra-high performance concrete (UHPC) is a function of fiber distribution and orientation, which are affected by the processing of the fresh material. In this study, the influences of two casting positions (mid-cast and end-cast) on strength and fracture properties of UHPCs with different fiber types and fiber contents were investigated. The results show that mid-cast specimens have higher flexural strength and fracture properties than end-cast specimens, while the compressive strength is almost unaffected by casting position. Compared to specimens with straight fibers, the flexural strength of specimens with hooked-end fibers is more likely to be affected by casting position. The residual load-to-peak load ratio is independent of casting position but affected by fiber type and fiber content.

scholarly journals Effects of Curing Conditions on the MECHANICAL and Microstructural Properties of Ultra-High-Performance Concrete (UHPC) Incorporating Iron Tailing Powder

Materials ◽  
2021 ◽  
Vol 14 (1) ◽  
pp. 215
Author(s):  
Dong Lu ◽  
Jing Zhong ◽  
Baobao Yan ◽  
Jing Gong ◽  
Ziye He ◽  
...  
Keyword(s):  
High Performance ◽  
Mechanical Performance ◽  
High Performance Concrete ◽  
Microstructural Properties ◽  
Ultra High Performance Concrete ◽  
Steam Curing ◽  
Curing Conditions ◽  
Curing Method ◽  
Mechanical And Microstructural Properties ◽  
Curing Regime

It has been reported that iron tailing powder (ITP) has the potential to partially replace cement to prepare ultra-high-performance concrete (UHPC). However, the reactivity of ITP particles in concrete largely depends on the curing method. This study investigates the effects of curing conditions on the mechanical and microstructural properties of UHPC containing ITP. To achieve this objective, three research tasks are conducted, including (1) preparing seven concrete formulations by introducing ITP; (2) characterizing their mechanical performance under different curing regimes; and (3) analyzing their microstructure by XRD patterns, FTIR analysis, and SEM observation. The experimental results show that there is an optimum ITP dosage (15%) for their application. The concrete with 15% ITP under standard curing obtains 94.3 MPa at 7 days, their early-age strength could be even further increased by ~30% (warm-water curing) and ~35% (steamed curing). The steam curing regime stimulates the activity of ITP and refines the microstructure. This study demonstrates the potential of replacing Portland cement with ITP in UHPC production.

Sign in / Sign up

Export Citation Format

Share Document