Aerodynamic Characterisation of Ramjet Missile through Combined External-internal Computational Fluid Dynamics Simulation

2016 ◽  
Vol 66 (6) ◽  
pp. 624 ◽  
Author(s):  
Anand Bhandarkar ◽  
Souraseni Basu ◽  
P. Manna ◽  
Debasis Chakraborty
Keyword(s):  
Experimental Data ◽  
Flow Field ◽  
High Speed ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Flow Simulation ◽  
Internal Flow ◽  
Dynamics Simulation ◽  
Navier Stokes ◽  
Navier Stokes Equations

<p>Combined external-internal flow simulation is required for the estimation of aerodynamic forces and moments of high speed air-breathing vehicle design. A wingless, X-tail configuration with asymmetrically placed rectangular air intake is numerically explored for which experimental data is available for different angles of attack. The asymmetrically placed air intakes and protrusions make the flow field highly three-dimensional and existing empirical relations are inadequate for preliminary design. Three dimensional Navier Stokes equations along with SST-kω turbulence model were solved with a commercial CFD solver to analyse the combined external and internal flow field of the configuration at different angles of attack. Estimated aerodynamic coefficients match well with experimental data and estimated drag coefficient are within 8.5 per cent of experimental data. Intake performance parameters were also evaluated for different angles of attack.</p>

Wind-Induced Response of ADSS during the Passage of High-Speed Train

2014 ◽  
Vol 590 ◽  
pp. 69-73
Author(s):  
Yu Wang ◽  
Qiang Gao ◽  
Hai Lin Wang
Keyword(s):  
Flow Field ◽  
High Speed ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Induced Response ◽  
Wind Flow ◽  
High Speed Train ◽  
Navier Stokes Equations ◽  
High Speed Trains

In this paper, the wind-induced response of the ADSS is analyzed when the high-speed trains pass by. The wind flow field of the high-speed train is simulated based on the three-dimensional Reynolds-averaged Navier–Stokes equations, combined with the k-ε turbulence model. The result is shown that the wind load acting on the ADSS is quite low and the stress of the line clamp increases a little.

scholarly journals Numerical Study of the Internal Flow Field of a Centrifugal Impeller

1994 ◽  
Author(s):  
Mou-jin Zhang ◽  
Chuan-gang Gu ◽  
Yong-miao Miao
Keyword(s):  
Flow Field ◽  
Stokes Equations ◽  
Numerical Study ◽  
Three Dimensional ◽  
Simple Algorithm ◽  
Internal Flow ◽  
Staggered Grid ◽  
Navier Stokes ◽  
Centrifugal Impeller ◽  
High Reynolds

The complex three-dimensional flow field in a centrifugal impeller with low speed is studied in this paper. Coupled with high–Reynolds–number k–ε turbulence model, the fully three–dimensional Reynolds averaged Navier–Stokes equations are solved. The Semi–Implicit Method for Pressure–Linked Equations (SIMPLE) algorithm is used. And the non–staggered grid arrangement is also used. The computed results are compared with the available experimental data. The comparison shows good agreement.

scholarly journals Three-Dimensional Turbulent Vortex Shedding From a Surface-Mounted Square Cylinder: Predictions With Large-Eddy Simulations and URANS

2014 ◽  
Vol 136 (6) ◽  
Author(s):  
B. A. Younis ◽  
A. Abrishamchi
Keyword(s):  
Experimental Data ◽  
Turbulence Model ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Large Eddy Simulations ◽  
Navier Stokes ◽  
Reynolds Stresses ◽  
Mean Flow ◽  
Navier Stokes Equations ◽  
Large Eddy

The paper reports on the prediction of the turbulent flow field around a three-dimensional, surface mounted, square-sectioned cylinder at Reynolds numbers in the range 104–105. The effects of turbulence are accounted for in two different ways: by performing large-eddy simulations (LES) with a Smagorinsky model for the subgrid-scale motions and by solving the unsteady form of the Reynolds-averaged Navier–Stokes equations (URANS) together with a turbulence model to determine the resulting Reynolds stresses. The turbulence model used is a two-equation, eddy-viscosity closure that incorporates a term designed to account for the interactions between the organized mean-flow periodicity and the random turbulent motions. Comparisons with experimental data show that the two approaches yield results that are generally comparable and in good accord with the experimental data. The main conclusion of this work is that the URANS approach, which is considerably less demanding in terms of computer resources than LES, can reliably be used for the prediction of unsteady separated flows provided that the effects of organized mean-flow unsteadiness on the turbulence are properly accounted for in the turbulence model.

Simulation of the subsonic flow in a high-speed centrifugal compressor impeller by the pressure-based method

1998 ◽  
Vol 212 (4) ◽  
pp. 269-287 ◽  
Author(s):  
Y Wang ◽  
S Komori
Keyword(s):  
High Speed ◽  
Compressible Flows ◽  
Incompressible Flows ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Centrifugal Impeller ◽  
Navier Stokes Equations ◽  
Compressor Impeller ◽  
Collocated Grid

A pressure-based finite volume procedure developed previously for incompressible flows is extended to predict the three-dimensional compressible flow within a centrifugal impeller. In this procedure, the general curvilinear coordinate system is used and the collocated grid arrangement is adopted. Mass-averaging is used to close the instantaneous Navier-Stokes equations. The covariant velocity components are used as the main variables for the momentum equations, making the pressure-velocity coupling easier. The procedure is successfully applied to predict various compressible flows from subsonic to supersonic. With the aid of the k-ɛ turbulence model, the flow details within a centrifugal impeller are obtained using the present procedure. Predicted distributions of the meridional velocity and the static pressure are reasonable. Calculated radial velocities and flow angles are favourably compared with the measurements at the exit of the impeller.

The Research on Numerical Simulation of the Centrifugal Pump and Configuration Perfected

2013 ◽  
Vol 694-697 ◽  
pp. 56-60
Author(s):  
Yue Jun Ma ◽  
Ji Tao Zhao ◽  
Yu Min Yang
Keyword(s):  
Numerical Simulation ◽  
Centrifugal Pump ◽  
Unstructured Grid ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Internal Flow ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Flow Phenomena ◽  
Simplec Algorithm

In the paper, on the basis of three-dimensional Reynolds-averaged Navier-Stokes equations and the RNG κ-ε turbulence model, adopting Three-dimensional unstructured grid and pressure connection the implicit correction SIMPLEC algorithm, and using MRF model which is supported by Fluent, this paper carries out numerical simulation of the internal flow of the centrifugal pump in different operation points. According to the results of numerical simulation, this paper analyzes the bad flow phenomena of the centrifugal pump, and puts forward suggests about configuration perfected of the centrifugal pump. In addition, this paper is also predicted the experimental value of the centrifugal pump performance, which is corresponding well with the measured value.

scholarly journals Numerical and Analytical Study of Fluid Dynamic Forces in Seals and Bearings

1988 ◽  
Vol 110 (3) ◽  
pp. 315-325 ◽  
Author(s):  
L. T. Tam ◽  
A. J. Przekwas ◽  
A. Muszynska ◽  
R. C. Hendricks ◽  
M. J. Braun ◽  
...  
Keyword(s):  
Flow Field ◽  
Stokes Equations ◽  
Fluid Dynamic ◽  
Three Dimensional ◽  
Circumferential Velocity ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Lumped Model ◽  
Destabilizing Factors ◽  
Recirculation Zones

A numerical model based on a transformed, conservative form of the three-dimensional Navier-Stokes equations and an analytical model based on “lumped” fluid parameters are presented and compared with studies of modeled rotor/bearing/seal systems. The rotor destabilizing factors are related to the rotative character of the flow field. It is shown that these destabilizing factors can be reduced through a descrease in the fluid average circumferential velocity. However, the rotative character of the flow field is a complex three-dimensional system with bifurcated secondary flow patterns that significantly alter the fluid circumferential velocity. By transforming the Navier-Stokes equations to those for a rotating observer and using the numerical code PHOENICS-84 with a nonorthogonal body fitted grid, several numerical experiments were carried out to demonstrate the character of this complex flow field. In general, fluid injection and/or preswirl of the flow field opposing the shaft rotation significantly intensified these secondary recirculation zones and thus reduced the average circumferential velocity, while injection or preswirl in the direction of rotation significantly weakened these zones. A decrease in average circumferential velocity was related to an increase in the strength of the recirculation zones and thereby promoted stability. The influence of the axial flow was analyzed. The lumped model of fluid dynamic force based on the average circumferential velocity ratio (as opposed to the bearing/seal coefficient model) well described the obtained results for relatively large but limited ranges of parameters. This lumped model is extremely useful in rotor/bearing/seal system dynamic analysis and should be widely recommended. Fluid dynamic forces and leakage rates were calculated and compared with seal data where the working fluid was bromotrifluoromethane (CBrF3). The radial and tangential force predictions were in reasonable agreement with selected experimental data. Nonsynchronous perturbation provided meaningful information for system lumped parameter identification from numerical experiment data.

Development of Numerical Code to Predict Three-Dimensional Sand Erosion Phenomena

2003 ◽  
Author(s):  
Kuki Junichi ◽  
Kazuyuki Toda ◽  
Makoto Yamamoto
Keyword(s):  
Flow Field ◽  
Stokes Equations ◽  
Suspended Particle ◽  
Three Dimensional ◽  
Numerical Procedure ◽  
Numerical Code ◽  
Particle Collision ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Sand Erosion

This paper presents a numerical procedure to predict a three-dimensional sand erosion phenomenon and the interaction between the flow field and the eroded surface. To simulate this phenomenon, the turbulent flow field, the particle trajectory and the amount of erosion on the eroded wall are calculated repeatedly. In computations of the flow field, compressible Navier-Stokes equations and low-Reynolds-number type k–ε turbulence model are adopted. Assuming that the concentration of suspended particle is dilute, particle-particle collision and the influence of particle motions on the flow field are neglected. The Neilson-Gilchrist erosion model is used to estimate the weight loss due to erosion. To verify the developed code, two types of 90-degree bends are computed. The results show that the present procedure can reasonably reproduce the sand erosion process and the temporal change of both the flow field and the wall surface qualitatively.

Heat Transfer in Film-Cooled Turbine Blades

1993 ◽  
Author(s):  
Vijay K. Garg ◽  
Raymond E. Gaugler
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Film Cooling ◽  
Stokes Equations ◽  
Turbine Blades ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Explicit Finite Difference ◽  
Control Volumes

In order to study the effect of film cooling on the flow and heat transfer characteristics of actual turbine blades, a three-dimensional Navier-Stokes code has been developed. An existing code (Chima and Yokota, 1990) has been modified for the purpose. The code is an explicit finite difference code with an algebraic turbulence model. The thin-layer Navier-Stokes equations are solved using a general body-fitted coordinate system. The effects of film cooling have been incorporated into the code in the form of appropriate boundary conditions at the hole locations on the blade surface. Each hole exit is represented by several control volumes, thus providing an ability to study the effect of hole shape on the film-cooling characteristics. Comparison with experimental data is fair. Further validation of the code is required, however, and in this respect, there is an urgent need for detailed experimental data on actual turbine blades.

A Finite Element Analysis of the Navier-Stokes Equations Applied to High Speed Thin Film Lubrication

1987 ◽  
Vol 109 (1) ◽  
pp. 71-76 ◽  
Author(s):  
J. O. Medwell ◽  
D. T. Gethin ◽  
C. Taylor
Keyword(s):  
Finite Element ◽  
High Speed ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Navier Stokes ◽  
The Finite Element Method ◽  
Thin Film Lubrication ◽  
Element Analysis ◽  
Navier Stokes Equations ◽  
Film Lubrication

The performance of a cylindrical bore bearing fed by two axial grooves orthogonal to the load line is analyzed by solving the Navier-Stokes equations using the finite element method. This produces detailed information about the three-dimensional velocity and pressure field within the hydrodynamic film. It is also shown that the method may be applied to long bearing geometries where recirculatory flows occur and in which the governing equations are elliptic. As expected the analysis confirms that lubricant inertia does not affect bearing performance significantly.

Sign in / Sign up

Export Citation Format

Share Document