Lignocellulose chemical composition and handsheet surface morphology analysis on oil palm residue biodelignification treatment using Bacillus cereus from Coptotermus curvignathus

In this paper TiN coating was prepared on stainless steel substrate using arc ion plating technique. The coating samples’ phases, surface morphology, micro-determination chemical composition, loss factor and damping ratio were tested. The phases of TiN coating were determined by X-ray diffraction (XRD) technique. The surface morphology and chemical composition of the TiN coating were analyzed by scanning electron microscope (SEM) and Energy Dispersive Spectrometer (EDS), respectively. The damping performance of the samples was measured by hammering activation according half power bandwidth method. The loss factor or damping ratio of samples were obtained according frequency response curve. The results showed that damping performance of samples was considerably improved by TiN coatings.

Download Full-text

Evaluation of chemical composition and nutritive potential of oil palm slurry fermented with cassava peel as feed for livestock

African Journal of Agricultural Research ◽

10.5897/ajar2013.7565 ◽

2014 ◽

Vol 9 (26) ◽

pp. 2062-2067

Author(s):

Oluwanike ABIOLA-OLAGUNJU ◽

Adejoke Adeneye MAKO ◽

Akintunde Olaleye AKINSOYINU

Keyword(s):

Chemical Composition ◽

Oil Palm ◽

Cassava Peel

Download Full-text

Structural and Surface Morphology Analysis of Nickel Phthalocyanine Thin Films

Advances in Materials Physics and Chemistry ◽

10.4236/ampc.2013.31a014 ◽

2013 ◽

Vol 03 (01) ◽

pp. 113-119 ◽

Cited By ~ 5

Author(s):

Mohammed T. Hussein ◽

Eman M. Nasir ◽

Addnan H. Al-Aarajiy

Keyword(s):

Thin Films ◽

Surface Morphology ◽

Nickel Phthalocyanine ◽

Morphology Analysis

Download Full-text

Synthesis and Properties of Sb Layered Te/Cd Stack Prepared by Elemental Stack Method

Advanced Materials Research ◽

10.4028/www.scientific.net/amr.488-489.76 ◽

2012 ◽

Vol 488-489 ◽

pp. 76-81 ◽

Cited By ~ 2

Author(s):

Subramani Shanmugan ◽

Mutharasu Devarajan ◽

Kamarulazizi Ibrahim

Keyword(s):

Thin Films ◽

Chemical Composition ◽

Surface Morphology ◽

Shape Analysis ◽

Structural Parameters ◽

X Ray Diffraction ◽

X Ray ◽

Electrical Studies ◽

Sb Doping ◽

Elemental Layer

Sb layered Te/Cd thin films have been prepared by using Stacked Elemental Layer (SEL) method. The presence of mixed phases (CdTe and Sb2Te3) in the films was confirmed by the x-ray diffraction technique. The calculated structural parameters demonstrated the feasibility of Sb doping via SEL method. The topographical and electrical studies of the synthesized thin films depicted the influence of Sb on both surface morphology and conductivity. The values of conductivity of the annealed films were in between 2 x 10-3 and 175 x 10-2 Scm-2. A desired chemical composition of films was confirmed from spectrum shape analysis using energy dispersive x-ray.

Download Full-text

Violet led bleaching: Efficacy and enamel surface morphology analysis

Dental Materials ◽

10.1016/j.dental.2018.08.053 ◽

2018 ◽

Vol 34 ◽

pp. e26

Author(s):

M. Kury ◽

B. Rezende ◽

B.C. Mendonça ◽

E.F. De Castro ◽

F.A. Rueggeberg ◽

...

Keyword(s):

Surface Morphology ◽

Enamel Surface ◽

Morphology Analysis

Download Full-text

Distribution on microhardness, chemical composition and structure over a layer of heat-resistant highyardness alloy formed by multilayer plasma surfacing in a nitrogen medium

Izvestiya vysshikh uchebnykh zavedenii. Fizika ◽

10.17223/00213411/64/7/75 ◽

2021 ◽

pp. 75-80

Author(s):

N.N. Malushin ◽

◽

D.A. Romanov ◽

A.P. Kovalev ◽

L.P. Bashchenko ◽

...

Keyword(s):

Chemical Composition ◽

Surface Morphology ◽

Elemental Composition ◽

High Quality ◽

Heat Resistant Alloy ◽

Resistant Alloy ◽

Heat Resistant ◽

Slag Inclusions ◽

Composition And Structure ◽

Plasma Surfacing

Microhardness distributions, surface morphology, and elemental composition of a deposited layer of a heat-resistant alloy of the type P2M8U steel formed by plasma surfacing in a protective-alloying nitrogen medium are studied. It was established that the surfacing technology and surfacing material allows to obtain a high-quality deposited alloy without cracks, pores, slag inclusions and defects of macro- and microstructure. It has been established that the deposited material is pearlite grains at the boundaries and grain junctions of which are carbonitrides based on iron, tungsten, chromium, molybdenum, aluminum (Fe6 W6 NC and AlN).

Download Full-text