scholarly journals Investigation of the Microstructure and Thermoelectric Properties of P-Type BiSbTe Alloys by Usage of Different Revolutions Per Minute (RPM) During Mechanical Milling

2017 ◽  
Vol 62 (2) ◽  
pp. 1167-1171 ◽  
Author(s):  
S.-M. Yoon ◽  
B. Madavali ◽  
Y.-N. Yoon ◽  
S.-J. Hong
Keyword(s):  
Electrical Conductivity ◽  
Thermoelectric Properties ◽  
High Energy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Size Refinement ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Energy Ball ◽  
P Type

AbstractIn this work, p-type Bi0.5Sb1.5Te3alloys were fabricated by high-energy ball milling (MA) and spark plasma sintering. Different revolutions per minute (RPM)s were used in the MA process, and their effect on microstructure, and thermoelectric properties of p-type Bi0.5Sb1.5Te3were systematically investigated. The crystal structure of milled powders and sintered samples were characterized using X-ray diffraction. All the powders exhibited the same morphology albeit with slight differences find at 1100 RPM conditions. A slight grain size refinement was observed on the fracture surfaces from 500 to 1100 RPM specimens. The temperature dependence of Seebeck coefficient, electrical conductivity, and power factors were measured as a function of temperature with different RPM conditions. The power factor shows almost same (~3.5 W/mK2at RT) for all samples due to unchanged Seebeck and electrical conductivity values. The peak ZT of 1.07 at 375K is obtained for 1100 RPM specimen due to low thermal conductivity.

Study on Phases and Thermoelectric Properties of Bulk FexCo4-xSb12 Sintered by MM-SPS

2011 ◽  
Vol 179-180 ◽  
pp. 294-297
Author(s):  
Ke Gao Liu ◽  
Shi Lei
Keyword(s):  
Thermoelectric Properties ◽  
Thermal Constant ◽  
X Ray Diffraction ◽  
Semiconducting Materials ◽  
X Ray ◽  
Seebeck Coefficients ◽  
Plasma Sintering ◽  
Electrical Resistivities ◽  
Spark Plasma ◽  
P Type

Bulk FexCo4-xSb12 with x varies from 0.1 to 2.0 were prepared by mechanical milling (MM) and spark plasma sintering (SPS). The phases of the products were characterized by X-ray diffraction (XRD) and their thermoelectric properties were tested by electric constant instrument and laser thermal constant instrument. Experimental results show that, the major phases of bulk FexCo4-xSb12 are skutterudite. The electrical resistivities of the products increase first and then decrease. The Seebeck coefficients ( ) are negative when x=0.1 at 100 °C and 200 °C while positive at 300~500 °C. The products with x=0.5~2.0 at 100~500 °C are P type semiconducting materials due to their positive values. The thermal conductivities of most samples increase first and then decrease with x increasing and the maximum is up to 0.39 Wm-1K-1 when x=1.0. The ZT values at 200~500 °C increase first and then decrease with x increasing when x=0.1~1.0 and x=1.0~2.0 respectively and the maximum ZT value is 0.196 when x=1.5 at 400 °C.

Corrosion Behavior and Hardness of Binary Mg Alloys Produced via High Energy Ball-Milling and Subsequent Spark Plasma Sintering

CORROSION ◽  
10.5006/3633 ◽  
2020 ◽  
Author(s):  
Mohammad Umar Farooq Khan ◽  
Taban Larimian ◽  
Tushar Borkar ◽  
Rajeev Gupta
Keyword(s):  
Ball Milling ◽  
Spark Plasma Sintering ◽  
Corrosion Behavior ◽  
High Energy ◽  
High Energy Ball Milling ◽  
X Ray Diffraction ◽  
X Ray ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Energy Ball

ABSTRACT In this work, nine nanocrystalline binary Mg alloys synthesized by high energy ball milling. The compositions, Mg-5wt.%M (M- Cr, Ge, Mn, Mo, Ta, Ti, V, Y, Zn) were milled with an objective of achieving non-equilibrium alloying. The milled alloys were consolidated via cold compaction (CC) at 25 ï‚°C and spark plasma sintering (SPS) at 300 ï‚°C. X-ray diffraction (XRD) analysis indicated grain refinement below 100 nm, and the scanning electron microscopy revealed homogeneous microstructures for all compositions. X-ray diffraction analysis revealed that most of the alloys showed a change in the lattice parameter, which indicates the formation of a solid solution. A significant increase in the hardness compared to unmilled Mg was observed for all the alloys. The corrosion behavior was improved in all the binary alloys compared to milled Mg. A significant decrease in the cathodic kinetics was evident due to Ge and Zn additions. The influence of the alloying elements on corrosion behavior has been categorized and discussed based on the electrochemical response of their respective binary Mg alloy.

Effect of High-Energy Ball-Milling and TiB2 Content on Microstructures and Properties of Cu-TiB2 Composites Sintered by SPS

2006 ◽  
Vol 118 ◽  
pp. 661-665 ◽  
Author(s):  
Dae Hwan Kwon ◽  
Thuy Dang Nguyen ◽  
Pyuck Pa Choi ◽  
Ji Soon Kim ◽  
Young Soon Kwon
Keyword(s):  
Electrical Conductivity ◽  
Ball Milling ◽  
High Energy ◽  
High Energy Ball Milling ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Energy Ball ◽  
Xrd Patterns ◽  
Short Time ◽  
Tib2 Particles

The microstructure and properties of Cu-TiB2 composites produced by high-energy ball-milling of TiB2 powders and spark-plasma sintering (SPS) were investigated. TiB2 powders were mechanically milled at a rotation speed of 1000rpm for short time in Ar atmosphere, using a planetary ball mill. To produce Cu-xTiB2 composites( x = 2.5, 5, 7.5 and 10wt.% ), the raw and milled TiB2 powders were mixed with Cu powders by means of a turbular mixer, respectively. Sintering of mixed powders was carried out in a SPS facility under vacuum. High-energy ball-milling resulted in refinement of TiB2 particles. XRD patterns of milled TiB2 powders indicated broader TiB2 peaks with decreased intensities. After sintering at 950 for 5min using the raw and milled TiB2 mixture powders, the sintered density decreased with increasing TiB2 content regardless of milling of TiB2. In the case of raw TiB2, hardness rapidly increased from 4 to 44 HRB with increasing TiB2 content. The electrical conductivity changed from 95.5 to 80.7 %IACS. For mixtures of Cu powders with milled TiB2 powders, hardness increased from 38 to 67 HRB as TiB2 content increased, while the electrical conductivity varied from 88% to 51 % IACS. When compared to compacts sintered with raw and milled TiB2 powders, the electrical conductivity of specimens with raw TiB2 powder was higher than that of specimens with milled TiB2 powder, while hardness was slightly lower.

scholarly journals Structure and Deformation Behavior of Ti-SiC Composites Made by Mechanical Alloying and Spark Plasma Sintering

Materials ◽  
2019 ◽  
Vol 12 (8) ◽  
pp. 1276 ◽  
Author(s):  
Dariusz Garbiec ◽  
Volf Leshchynsky ◽  
Alberto Colella ◽  
Paolo Matteazzi ◽  
Piotr Siwak
Keyword(s):  
Mechanical Alloying ◽  
Spark Plasma Sintering ◽  
Indentation Size Effect ◽  
Sintering Temperature ◽  
High Energy ◽  
Indentation Size ◽  
X Ray ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Energy Ball

Combining high energy ball milling and spark plasma sintering is one of the most promising technologies in materials science. The mechanical alloying process enables the production of nanostructured composite powders that can be successfully spark plasma sintered in a very short time, while preserving the nanostructure and enhancing the mechanical properties of the composite. Composites with MAX phases are among the most promising materials. In this study, Ti/SiC composite powder was produced by high energy ball milling and then consolidated by spark plasma sintering. During both processes, Ti3SiC2, TiC and Ti5Si3 phases were formed. Scanning electron microscopy, energy-dispersive X-ray spectroscopy and X-ray diffraction study showed that the phase composition of the spark plasma sintered composites consists mainly of Ti3SiC2 and a mixture of TiC and Ti5Si3 phases which have a different indentation size effect. The influence of the sintering temperature on the Ti-SiC composite structure and properties is defined. The effect of the Ti3SiC2 MAX phase grain growth was found at a sintering temperature of 1400–1450 °C. The indentation size effect at the nanoscale for Ti3SiC2, TiC+Ti5Si3 and SiC-Ti phases is analyzed on the basis of the strain gradient plasticity theory and the equation constants were defined.

THERMOELECTRIC PROPERTIES OF p-TYPE SKUTTERUDITES (Pr0.25Nd0.75)xFe3CoSb12 BY LEVITATION MELTING AND SPARK PLASMA SINTERING

2013 ◽  
Vol 06 (05) ◽  
pp. 1340006 ◽  
Author(s):  
JINGSHU XU ◽  
CHENGUANG FU ◽  
JIAN XIE ◽  
XINBING ZHAO ◽  
TIEJUN ZHU
Keyword(s):  
Thermal Conductivity ◽  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Spark Plasma Sintering ◽  
Thermoelectric Properties ◽  
Lattice Thermal Conductivity ◽  
Levitation Melting ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
P Type

The p-type skutterudite compounds of ( Pr 0.25 Nd 0.75)x Fe 3 CoSb 12 (x = 0.67–0.78) have been successfully synthesized by levitation melting followed by annealing and spark plasma sintering. The thermoelectric properties have been characterized by the measurements of Seebeck coefficient, electrical conductivity and thermal conductivity in the temperature range from 300 K to 850 K. The improvement in the thermoelectric properties was realized due to the reduction in the lattice thermal conductivity when the voids were partially filled by Pr 0.25 Nd 0.75. The maximum ZT value of ~ 0.83 for ( Pr 0.25 Nd 0.75)0.76 Fe 3 CoSb 12 was obtained at 700 K.

Investigating the key role of carrier transport mechanism in SnSe nanoflakes with enhanced thermoelectric power factor

2021 ◽  
Author(s):  
Srikanth Mandava ◽  
Neeta Bisht ◽  
Anjali Saini ◽  
Mukesh Kumar Bairwa ◽  
Khasimsaheb Bayikadi ◽  
...  
Keyword(s):  
Electrical Conductivity ◽  
Ab Initio ◽  
Spark Plasma Sintering ◽  
Thermoelectric Properties ◽  
Power Factor ◽  
Temperature Range ◽  
Carrier Scattering ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
P Type

Abstract A novel SnSe nanoake system is explored for its thermoelectric properties from both experiments and ab initio study. The nanoakes of the low temperature phase of SnSe (Pnma) are synthesized employing a fast and efficient refluxing method followed by spark plasma sintering at two different temperatures. We report an enhanced power factor (12 W/mK2 - 67 W/mK2 in the temperature range 300 K-600 K) in our p-type samples. We find that the prime reason for a high PF in our samples is a significantly improved electrical conductivity (1050 S/m - 2180 S/m in the temperature range 300 K-600 K). From our ab initio band structure calculations accompanied with the models of temperature and surface dependent carrier scattering mechanisms, we reveal that an enhanced electrical conductivity is due to the reduced carrier-phonon scattering in our samples. The trans- port calculations are performed using the Boltzmann transport equation within relaxation time approximation. With our combined experimental and theoretical study, we demonstrate that the thermoelectric properties of p-type Pnma-SnSe could be improved by tuning the carrier scattering mechanisms with a control over the spark plasma sintering temperature.

scholarly journals Fabrication and Thermoelectric Properties of Graphene/Bi2Te3Composite Materials

2013 ◽  
Vol 2013 ◽  
pp. 1-5 ◽  
Author(s):  
Beibei Liang ◽  
Zijun Song ◽  
Minghui Wang ◽  
Lianjun Wang ◽  
Wan Jiang
Keyword(s):  
Thermoelectric Properties ◽  
Thermoelectric Materials ◽  
Figure Of Merit ◽  
Conductivity Measurement ◽  
Testing Temperature ◽  
X Ray Diffraction ◽  
X Ray ◽  
Dimensionless Figure Of Merit ◽  
Plasma Sintering ◽  
Spark Plasma

Graphene/Bi2Te3thermoelectric materials were prepared by spark plasma sintering (SPS) using hydrothermal synthesis of the powders as starting materials. The X-ray diffraction (XRD) and field emission scanning electron microscope (FE-SEM) were used to investigate the phase composition and microstructure of the as-prepared materials. Electrical resistivity, Seebeck coefficient, and thermal conductivity measurement were applied to analyze the thermoelectric properties. The effect of graphene on the performance of the thermoelectric materials was studied. The results showed that the maximum dimensionless figure of merit of the graphene/Bi2Te3composite with 0.2 vol.% graphene was obtained at testing temperature 475 K, 31% higher than the pure Bi2Te3.

Thermoelectric Properties of Zr0.5Hf0.5Ni0.8Pd0.2Sn0.99Sb0.01 half-Heusler Alloy with WO3 Inclusions

2010 ◽  
Vol 1267 ◽  
Author(s):  
Julien Pierre Amelie Makongo Mangan ◽  
Pravin Paudel ◽  
Dinesh Misra ◽  
Pierre F. P. Poudeu
Keyword(s):  
Electrical Conductivity ◽  
Thermoelectric Properties ◽  
Figure Of Merit ◽  
Lattice Thermal Conductivity ◽  
High Energy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Lower Figure ◽  
Synthesized Materials

AbstractZr0.5Hf0.5Ni0.8Pd0.2Sn0.99Sb0.01 composites with various concentrations of WO3 inclusions were synthesized by mechanical alloying using high energy shaker mill. High density hot pressed pellets of the synthesized materials were characterized using powder X-ray diffraction and transmission electron microscopy and their thermoelectric properties were investigated in the temperature range from 300 to 750 K. The electrical conductivity of the composites at 300 K decreases from 2500 S/cm for 0 wt.% WO3 alloy to 2200 S/cm for the composite with 2 wt.% WO3 inclusion. The electrical conductivity of composites containing 5 wt.% and 10 wt.% WO3 inclusions showed sharp increases with increasing WO3 content. The electrical conductivity of the composites monotonically decreases with rising temperature. All samples showed n-type semiconducting behavior and the thermopower values decrease with increasing WO3 content. The lattice thermal conductivity of the composites increases with increasing WO3 content. However, these values are about 30% lower than that of Zr0.5Hf0.5Ni0.8Pd0.2Sn0.99Sb0.01 alloy prepared by high temperature solid-state techniques. The synthesized composites showed lower figure of merit than the half-Heusler matrix due to large reduction in the thermopower values with increasing WO3 content.

scholarly journals Microstructure And Thermoelectric Properties Of Tags-90 Compounds Fabricated By Mechanical Milling Process

2015 ◽  
Vol 60 (2) ◽  
pp. 1231-1234 ◽  
Author(s):  
H.-S Kim ◽  
M. Babu ◽  
S.-J. Hong
Keyword(s):  
Thermoelectric Properties ◽  
Milling Time ◽  
Fine Particles ◽  
High Energy ◽  
Dispersion Analysis ◽  
Milling Process ◽  
X Ray Diffraction ◽  
Fine Grain ◽  
Plasma Sintering ◽  
Spark Plasma

Abstract TAGS-90 compound powder was directly prepared from the elements by high-energy ball milling (HEBM) and subsequently consolidated by a spark plasma sintering (SPS). Effect of milling time on the microstructure and thermoelectric properties of the samples were investigated. The particle size of fabricated powders were decreased with increasing milling time, finally fine particles with ~1μm size was obtained at 90 min. The SPS samples exhibited higher relative densities (>99%) with fine grain size. X-ray diffraction analysis (XRD) and energy dispersion analysis (EDS) results revealed that all the samples were single phase of GeTe with exact composition. The electrical conductivity of samples were decreased with milling time, whereas Seebeck coefficient increased over the temperature range of RT~450°C. The highest power factor was 1.12×10−3W/mK2 obtained for the sample with 90 min milling at 450°C.

scholarly journals Synthesis and characterization of Ag-8 %wt Cr2O3 composites prepared by different densification processes

2018 ◽  
Vol 50 (3) ◽  
pp. 323-335
Author(s):  
Nima Mansourirad ◽  
Mohammad Ardestani ◽  
Reza Afshar
Keyword(s):  
Silver Oxide ◽  
High Energy ◽  
Processing Route ◽  
X Ray Diffraction ◽  
X Ray ◽  
Microstructural Parameters ◽  
Dense Microstructure ◽  
Plasma Sintering ◽  
Spark Plasma

A novel Ag-8 %wt Cr2O3 composite prepared via powder metallurgy route. Silver and chromium oxides were used as starting powders. The powder mixtures were mechanically milled by a SPEX high energy mill for 5 h. Based on the thermogravimetric analysis (TGA) and X-Ray Diffraction (XRD) results, the milled powders were calcined in an argon atmosphere at 550?C. During calcination, the silver oxide decomposed into silver. The results showed that the Heckel equation was the preferred one for description the cold compressibility of the powders. The calcined powders were consolidated by Press-Sinter-Repress (PSR), Press-Sinter-Repress-Anneal (PSRA) and Spark Plasma Sintering (SPS) processes. The Field Emission Scanning Electron Microscope (FESEM) investigations showed a nearly dense microstructure of the sintered samples. However, the hardness of the pressed-sintered-repressed samples was 81 Vickers which was the highest among the processed specimen. Furthermore, the flexural strength of the PSR and SPS processed samples were 231 and 255 MPa, respectively which were too higher than that of the annealed specimens. The results confirmed the effect of microstructural parameters such as Cr2O3 particle size and processing route on the mechanical properties of the sintered composites.

Sign in / Sign up

Export Citation Format

Share Document