Optimization of Process Parameters in Micro-EDM of Ti-6Al-4V Alloy

2016 ◽  
Vol 16 (1) ◽  
pp. 41-49
Author(s):  
V. Krishnaraj
Keyword(s):  
Titanium Alloy ◽  
Titanium Alloys ◽  
Process Parameters ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Performance Criteria ◽  
Machining Parameters ◽  
Micro Edm ◽  
Micro Holes ◽  
Pulse On Time

AbstractTitanium alloys are categorized as light weight materials posse greater strength and toughness and are usually known to create major challenges during conventional and non-conventional machining. In general, these alloys are referred as difficult to machine materials. Titanium alloy (Ti-6Al-4V) suffers poor machinability for most cutting processes, especially the generation of micro-holes using traditional machining methods. Electrical Discharge Machining (EDM) is suitable for machining titanium alloys, although selection of machining parameters for higher machining rate and accuracy is a challenging task in machining micro-holes. Discharge current, pulse ON time and Flushing pressure were considered as the major influencing machining parameters and Material Removal Rate (MRR), Tool Wear Rate (TWR) and Hole Taper were considered as the performance criteria. It is observed that machining performances are affected mostly by the peak current and pulse-on time during micro-electro discharge machining of titanium alloy. Mathematical models have been developed using multiple regression analysis, to establish the relationship between various significant process parameters and micro-EDM performance criteria. Also, studies have been made to examine the influence of various process parameters on the quality of the machined micro-hole.

An intelligent approach to optimize the electrical discharge machining of titanium alloy by simple optimization algorithm

2020 ◽  
pp. 095440892096468
Author(s):  
Anshuman Kumar Sahu ◽  
Joji Thomas ◽  
Siba Sankar Mahapatra
Keyword(s):  
Titanium Alloy ◽  
Boron Carbide ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Optimal Solution ◽  
Machining Parameters ◽  
Machining Performance ◽  
Intelligent Approach ◽  
Pulse On Time

Electrical discharge machining (EDM) is a thermo-electrical process that can be conveniently utilized for generating complex shaped profiles on hard-to-machine conductive materials using metallic tool electrodes. In this work, composite tools made of copper-tungsten-boron carbide (Cu-W-B4C) manufactured by powder metallurgy (PM) route are used during machining of titanium alloy (Ti6Al4V). The effect of four input machining parameters viz. current, pulse-on-time, duty cycle and percentage of tungsten and boron carbide on material removal rate (MRR), tool wear rate (TWR) and surface roughness (Ra) is studied. A novel meta-heuristic approach such as simple optimization (SOPT) algorithm has been used for single and multi-objective optimization. The pareto-optimal solutions obtained by SOPT have been ranked by VIKOR method to find out the best suitable optimal solution. Analysis of experimental data suggests vital information for controlling the machining parameters to improve the machining performance.

Investigating the Effect of Machining Parameters on Microdrilling of Titanium Grade 19 Alloy

2013 ◽  
Author(s):  
Shivraj Yeole ◽  
Nagabhushana Ramesh Nunna ◽  
Balu Naik Banoth
Keyword(s):  
Process Parameters ◽  
Material Removal ◽  
Removal Rate ◽  
Electrode Wear ◽  
Machining Parameters ◽  
Micro Edm ◽  
Electrode Diameter ◽  
Micro Holes ◽  
Titanium Grade ◽  
Edm Process

Electrical Discharge Micro Drilling (EDMD) is considered as one of the most effective method for machining difficult to cut and hard materials like titanium alloy. However, selection of process parameters for achieving superior surface finish, higher machining rate and accuracy is a challenging task in drilling micro-holes. In this paper, an attempt is made to optimize micro-EDM process parameters for drilling micro holes on titanium grade 19 alloy. In order to verify the optimal micro-EDM process parameters settings, material removal rate (MRR), electrode wear rate (EWR) and over cut (OC) were chosen as the responses to be observed. Pulse on time, pulse off time, electrode diameter and current were selected as the governing process parameters for evaluation by Taguchi method. Nine micro holes of 300 μm, 400 μm and 500 μm were drilled using L9 orthogonal array (OA) design. Optimal combination of machining parameters were obtained through Signal-to-Noise (S/N) ratio analysis. It is seen that machining performances like material removal rate and overcut are affected by the peak current whereas electrode wear is affected by peak current and electrode diameter. Morphology of the micro holes has been studied through SEM micrographs of machined micro-hole.

scholarly journals A Study on Optimization of Process Parameters in Machining of Bronze using Wire-EDM

2021 ◽  
pp. 484-493
Author(s):  
Gajanan Kamble ◽  
Dr. N. Lakshamanaswamy ◽  
Gangadhara H S ◽  
Sharon Markus ◽  
N. Rajath
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Material Removal Rate ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Machining Parameters ◽  
Wire Edm ◽  
Pulse On Time ◽  
Pulse Off Time

Wire cut electrical discharge machining (WEDM) is a hybrid manufacturing technology which enables machining of all engineering materials. This research article deals with investigation on Optimization of the Process Parameters of the wire cut EDM of Bronze material of dimension (80*80*40) in mm. Material removal rate, Surface roughness and Kerf width were studied against the process parameters such as Pulse on time(TON), Pulse off time (TOFF) and Current(IP). The machining parameters for wire EDM were optimized for achieving the combined objectives. As there are three input parameters 27 experiments is carried out and full factorial is used. Optimized parameters were found using (ANOVA) and the error percentage can be validated and parameter contribution for the Material removal rate (MRR) and Surface roughness were found.

Optimization and surface modification in electrical discharge machining of AA 6061/SiCp composite using Cu–W electrode

2015 ◽  
Vol 231 (3) ◽  
pp. 332-348 ◽  
Author(s):  
Balbir Singh ◽  
Jatinder Kumar ◽  
Sudhir Kumar
Keyword(s):  
Process Parameters ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Surface Characteristics ◽  
Electrode Wear ◽  
Material Transfer ◽  
Machined Surface ◽  
Recast Layer Thickness ◽  
Pulse On Time ◽  
Pulse Off Time

This paper presents the experimental investigation on the electro-discharge machining of aluminum alloy 6061 reinforced with SiC particles using sintered Cu–W electrode. Experiments have been designed as per central composite rotatable design, using response surface methodology. Machining characteristics such as material removal rate (MRR), electrode wear ratio (EWR), and surface roughness (SR) have been investigated under the influence of four electrical process parameters; namely peak current, pulse on time, pulse off time, and gap voltage. The process parameters have been optimized to obtain optimal combination of MRR, EWR, and SR. Further, the influence of sintered Cu–W electrode on surface characteristics has been analyzed with scanning electron microscopy, energy dispersive spectroscopy, and Vicker microhardness tests. The results revealed that all the process parameters significantly affect MRR, EWR, and SR. The machined surface properties are modified as a result of material transfer from the electrode. The recast layer thickness is increased at higher setting of electrical parameters. The hardness across the machined surface is also increased by the use of sintered Cu–W electrode.

Mathematical Modeling of Machining Parameters in Electrical Discharge Machining with Cu-B4C Composite Electrode

2012 ◽  
Vol 488-489 ◽  
pp. 871-875
Author(s):  
V. Anandakrishnan ◽  
V. Senthilkumar
Keyword(s):  
Mathematical Models ◽  
Current Pulse ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Machining Parameters ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time ◽  
Selection Of

Copper based metal matrix composite reinforced with Boron Carbide is a newly developed Electrical Discharge Machining (EDM) electrode showing better performance than the conventional copper based electrode. Right selection of machining parameters such as current, pulse on time and pulse off time is one of the most important aspects in EDM. In this paper an attempt has been made to develop mathematical models for relating the Material Removal Rate (MRR), Tool Removal Rate (TRR) and Surface roughness (Ra) to machining parameters (current, pulse-on time and pulse-off time). Furthermore, a study was carried out to analyze thSubscript texte effects of machining parameters on various performance parameters such as, MRR, TRR and Ra. The results of Analysis of Variance (ANOVA) indicate that the proposed mathematical models, can adequately describe the performance within the limits of the factors being studied. Response surface modeling is used to develop surface and contour graphs to analyze the effects of EDM input parameters on outer parameters.

scholarly journals Multi-Objective Optimization of Process Parameters for Powder Mixed Electrical Discharge Machining of Inconel X-750 Alloy Using Taguchi-Topsis Approach

2021 ◽  
Vol 71 (1) ◽  
pp. 1-18
Author(s):  
Basha Shaik Khadar ◽  
Raju M. V. Jagannadha ◽  
Kolli Murahari
Keyword(s):  
Boron Carbide ◽  
Process Parameters ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Optimization Technique ◽  
Dielectric Fluid ◽  
Carbide Powder ◽  
Powder Concentration ◽  
Pulse On Time ◽  
Pulse Off Time

Abstract The paper investigates the influence of boron carbide powder (B4C) mixed in dielectric fluid on EDM of Inconel X-750 alloy. The process parameters selected as discharge current (Ip), pulse on time(Ton), pulse off time(Toff), boron carbide(B4C) powder concentration to examine their performance responses on Material Removal Rate (MRR), Surface Roughness(Ra) and Recast Layer Thickness (RLT).In this study, o examine the process parameters which influence the EDM process during machining of Inconel X-750 alloy using combined techniques of Taguchi and similarity to ideal solutions (TOPSIS).Analysis of variance (ANOVA) was conducted on multi-optimization technique of Taguchi-TOPSIS. ANOVA results identified the best process parameters and their percentages. It developed the mathematical equation on Taguchi-TOPSIS performance characteristics results. The multi optimization results indicated that Ip and Toff are more significant parameters; V, and Ton parameters are less significant. Finally, surface structures were studied at optimized EDM conditions by using scanning electron microscope (SEM).

EXPERIMENTAL INVESTIGATION OF MICRO-EDM OPERATION IN INCONEL 718

2021 ◽  
pp. 2150102
Author(s):  
MAYANK CHOUBEY ◽  
K. P. MAITY
Keyword(s):  
Experimental Investigation ◽  
Inconel 718 ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Micro Edm ◽  
Machining Processes ◽  
Machining Time ◽  
Machine Material ◽  
Micro Holes ◽  
Unconventional Machining

The increasing trends towards miniaturized and lightweight components for various engineering and aerospace applications by unconventional machining the demand for micro-electrical discharge machining (EDM) have become increasingly wide. Micro-EDM is one of the most promising unconventional machining processes as compared to other unconventional machining due to its lower cost, ease of operation, and accuracy. This research explores the experimental investigation of micro-EDM operation on hard and difficult to machine material Inconel 718. The micro-holes were fabricated on an Inconel 718 workpiece with a copper electrode. The influence of input process parameters on material removal rate (MRR), machining time, and quality of the fabricated micro-holes were studied. Overcut and taperness of the fabricated micro-sized through holes were measured to address the accuracy of the fabricated micro-holes in micro-EDM operation. Experimental results reveal that the increase in current and voltage increases the MRR, and reduced machining time but at the cost of dimensional accuracy of the fabricated holes. The high value of current and voltage resulted in poor surface quality. The optimum machining condition that gives higher MRR with higher machining precision was obtained by experimenting while machining Inconel 718.

scholarly journals Experimental Study on the Influence of Machining Conditions on the Quality of Electrical Discharge Machined Surfaces of aluminum alloy Al5052

Machines ◽  
2020 ◽  
Vol 8 (1) ◽  
pp. 12 ◽  
Author(s):  
Angelos P. Markopoulos ◽  
Emmanouil-Lazaros Papazoglou ◽  
Panagiotis Karmiris-Obratański
Keyword(s):  
Aluminum Alloy ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
White Layer ◽  
Machining Parameters ◽  
Machining Processes ◽  
Machining Conditions ◽  
Pulse On Time ◽  
Machined Surfaces

Although electrical discharge machining (EDM) is one of the first established non-conventional machining processes, it still finds many applications in the modern industry, due to its capability of machining any electrical conductive material in complex geometries with high dimensional accuracy. The current study presents an experimental investigation of ED machining aluminum alloy Al5052. A full-scale experimental work was carried out, with the pulse current and pulse-on time being the varying machining parameters. The polishing and etching of the perpendicular plane of the machined surfaces was followed by observations and measurements in optical microscope. The material removal rate (MRR), the surface roughness (SR), the average white layer thickness (AWLT), and the heat affected zone (HAZ) micro-hardness were calculated. Through znalysis of variance (ANOVA), conclusions were drawn about the influence of machining conditions on the EDM performances. Finally, semi empirical correlations of MRR and AWLT with the machining parameters were calculated and proposed.

Multi-Objective Optimization of Electrical Discharge Machining Parameters for 2024 Aluminum Alloy Using Grey-Taguchi Method

2020 ◽  
Vol 998 ◽  
pp. 55-60
Author(s):  
Jurapun Phimoolchat ◽  
Apiwat Muttamara
Keyword(s):  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Electrode Wear ◽  
Machining Parameters ◽  
Multi Objective Optimization ◽  
2024 Aluminum Alloy ◽  
Multi Objective ◽  
Effect Estimation ◽  
Voltage Performance ◽  
Pulse On Time

This paper focused on Grey relational analysis (GRA) to optimize EDM parameters through multi-objective optimization for Al2024 aluminum and electrode graphite ISO-63 was used as a cutting tool. The process parameters pulse on time, duty factor, pulse current and open voltage. Performance characteristics examined included material removal rate (MRR), electrode wear ratio (EWR) and surface roughness (SR). Taguchi’s 27 experimental designs, often called an orthogonal array (OA), was utilized to ignore interaction and concentrate on main effect estimation. GRA was performed to optimize input parameters levels. Results were that MRR increased from 35.00 to 35.11 mm3/min, EWR decreased from 11.63 to 10.89 mm3/min, and SR decreased from 5.01 to 4.97 μm. Taguchi and GRA resulted in clear improvements in MRR, EWR, and SR.

scholarly journals Parametric optimization of wire cut electrical discharge machining

2014 ◽  
Vol 3 (2) ◽  
pp. 212
Author(s):  
M. Durairaj ◽  
A.K.S. Ansari ◽  
M. H. Gauthamkumar
Keyword(s):  
Surface Roughness ◽  
Orthogonal Array ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Fluid Pressure ◽  
Performance Criteria ◽  
Dielectric Fluid ◽  
Machining Parameters ◽  
Pulse On Time ◽  
Pulse Off Time

Wire Electrical Discharge Machining is a manufacturing process whereby a desired shape is obtained using electrical discharges (or) by repetitive spark cycle. Precision and intricate machining are the strengths. Machining parameters tables provided by the machine tool manufacturers often do not meet the operator requirements. Selection of optimum machining and machining parameters combinations is needed for obtaining higher cutting efficiency and accuracy. In this present study, machining is done using Wire-Cut EDM and optimization of surface roughness is done using Taguchis design of experiments. Experimentation was planned as per Taguchis L16 orthogonal array. Each experiment has been performed under different cutting conditions of gap voltage, pulse ON time, and pulse OFF time and Wire feed. Dielectric fluid pressure, wire speed, wire tension, resistance and cutting length are taken as fixed parameters. Inconel 800 was selected as a work material to conduct the experiments. From experimental results, the surface roughness was determined for each machining performance criteria. Signal to noise ratio was applied to measure the performance characteristics deviating from the actual value. Finally, experimental confirmation was carried out to identify the effectiveness of this proposed method. Keywords: Optimization; Taguchis L-16 Orthogonal Array; Surface Roughness; S/N Ratio.

Sign in / Sign up

Export Citation Format

Share Document