scholarly journals Research of influence of open-winding faults on properties of brushless permanent magnets motor

Open Physics ◽  
2017 ◽  
Vol 15 (1) ◽  
pp. 959-964
Author(s):  
Piotr Bogusz ◽  
Mariusz Korkosz ◽  
Adam Powrózek ◽  
Jan Prokop ◽  
Piotr Wygonik
Keyword(s):  
Permanent Magnets ◽  
Simulation Models ◽  
Brushless Dc Motor ◽  
Bldc Motor ◽  
Test Results ◽  
Hybrid Drive ◽  
Brushless Dc ◽  
Laboratory Test Results ◽  
Aerial Vehicle ◽  
The Subject

AbstractThe paper presents an analysis of influence of selected fault states on properties of brushless DC motor with permanent magnets. The subject of study was a BLDC motor designed by the authors for unmanned aerial vehicle hybrid drive. Four parallel branches per each phase were provided in the discussed 3-phase motor. After open-winding fault in single or few parallel branches, a further operation of the motor can be continued. Waveforms of currents, voltages and electromagnetic torque were determined in discussed fault states based on the developed mathematical and simulation models. Laboratory test results concerning an influence of open-windings faults in parallel branches on properties of BLDC motor were presented.

scholarly journals PID Control System on Brushless DC Motor for Quadcopter Balance

Jurnal INFORM ◽  
2021 ◽  
Vol 6 (2) ◽  
pp. 110-114
Author(s):  
Mochamad Mobed Bachtiar ◽  
Fernando Ardilla ◽  
Muhammad Faiz Hasbi ◽  
Iwan Kurnianto Wibowo
Keyword(s):  
Pid Control ◽  
Control Method ◽  
Dc Motor ◽  
Unmanned Aircraft ◽  
Integrated System ◽  
Brushless Dc Motor ◽  
Test Results ◽  
Brushless Dc ◽  
Aerial Vehicle ◽  
Aircraft System

Unmanned Aerial Vehicle (UAV) is an unmanned aircraft system that is no longer a special need but has become a general need for the community, and one example is used to capture everyday moments through photos or videos from the air. Among the models of UAV aircraft is the quadcopter, where there is a flight controller that functions to fly the quadcopter by adjusting the speed of each motor. The flight controller that is often used today is the Pixhawk manufacturer. The Pixhawk module is an integrated system that the factory has provided, so it cannot be modified in terms of control and I/O. This research focuses on making an independent flight controller that can be used to fly a quadcopter. The control method that is implanted is Proportional Integral Derivative or commonly known as PID. The flight controller uses the PID control method to adjust each Brushless DC Motor (BLDC) speed to maintain stability while flying. From the test results, the quadcopter can fly stably with KP parameters of 2.5, KI of 0.6, and KD of 1.0. The response time in processing feedback is 3s.

Dynamic Characterization of Brushless DC Motors and Propellers for Flight Applications

2017 ◽  
Vol 05 (03) ◽  
pp. 159-167 ◽  
Author(s):  
Dominic Muzar ◽  
Eric Lanteigne ◽  
Justin McLeod
Keyword(s):  
Simple Model ◽  
Brushless Dc Motor ◽  
Dynamic Characterization ◽  
Brushless Dc Motors ◽  
Brushless Dc ◽  
Dc Motors ◽  
Simple Motor ◽  
Aerial Vehicle ◽  
Selection Of

Although there exist a number of accurate unmanned aerial vehicle (UAV) thruster models, these models require the precise measurements of several motor and propeller characteristics. This paper presents a simple motor and propeller model that relies solely upon data provided by manufacturers. The model is validated by comparing theoretical motor and propeller behavior to experimental results obtained from thrust tests in a wind tunnel. The objective is to provide an accurate yet simple model to facilitate the selection of appropriate brushless DC motor and propeller combinations for flight applications.

scholarly journals Analysis of a Permanent-Magnet Brushless DC Motor with Fixed Dimensions

2010 ◽  
Vol 26 (1) ◽  
pp. 78-81
Author(s):  
Uldis Brakanskis ◽  
Janis Dirba ◽  
Ludmila Kukjane ◽  
Viesturs Drava
Keyword(s):  
Magnetic Flux ◽  
Permanent Magnet ◽  
Permanent Magnets ◽  
Dc Motor ◽  
Magnetic Flux Density ◽  
Brushless Dc Motor ◽  
Outer Diameter ◽  
Zone Length ◽  
Brushless Dc ◽  
Permanent Magnet Brushless Dc

Analysis of a Permanent-Magnet Brushless DC Motor with Fixed DimensionsThe purpose of this paper is to describe the analysis of a permanent-magnet brushless DC motor with fixed outer diameter and active zone length. The influence of air gap, material of permanent magnets and their size on the magnetic flux density of the machine and magnetic flux is analyzed. The work presents the calculations of two programs, the comparison of the results and the most suitable combination of factors that has been found.

scholarly journals Development of a high-quality brushless dc electric drive systems model

Vestnik IGEU ◽  
2020 ◽  
pp. 31-45
Author(s):  
T.H. Abuziarov ◽  
A.S. Plehov ◽  
A.B. Dar’enkov ◽  
A.I. Ermolaev
Keyword(s):  
Electric Drive ◽  
Electric Motor ◽  
Permanent Magnets ◽  
Structural Features ◽  
Bldc Motor ◽  
Electric Drives ◽  
Brushless Dc ◽  
Systems Model ◽  
Semiconductor Converter ◽  
Torque Pulsations

When designing electric drives based on brushless DC motors with permanent magnets (BLDC), which have low level torque pulsations, the problem of modelling non-standard topological solutions appears. The known models of BLDC motors are either based on the assumptions about the symmetry of the stator pa-rameters of the electric motor and/or the ideal form of the phase back-EMF waveform, which reduce the accuracy of evaluating the effectiveness of the proposed solutions or prove unusable for modelling an operation of the electric motor with a non-standard semiconductor converter. It is necessary to develop a mathematical model of the BLDC motor-based electric drive that takes into account the structural features of the electric motor and allows for semiconductor converter configuration variability. The model is designed in the Matlab Simulink environment. The verification is carried out by comparing the modelling results with experimental data obtained previously by other researchers. The proposed method for generating phase back-EMF in the BLDC motor model provides the possibility for the user to set the EMF form templates independent for each phase. The proposed method for stator circuit simulating provides the user with access to each of the stator windings leads as well as with the possibility of asymmetric determination of each parameter of the electric motor. Upon verification, it has been shown that the difference in the control points between the simulated and experimental speed-torque curves does not exceed 3,5 %. The developed model allows analyzing the static and dynamic characteristics of operation modes of non-standard topology BLDC motor-based electric drives taking into account the stator pa-rameters asymmetry and the real phase back-EMF waveform. The specified features of the model allow exploring the operation of the designed electric drive, taking into account the BLDC motor and converter design. The model can be applied when checking atypical design decisions and when changing the set parameters of the electric drive and restrictions on working conditions and target functions to refine the control system algorithms and automate the search for optimal parameters of the motor and the semiconductor converter.

scholarly journals Brushless DC Motor Speed Controller for Electric Motorbike

2018 ◽  
Vol 9 (2) ◽  
pp. 859
Author(s):  
Mohd Syakir Adli ◽  
Noor Hazrin Hany Mohamad Hanif ◽  
Siti Fauziah Toha Tohara
Keyword(s):  
Pid Controller ◽  
Dc Motor ◽  
Battery Pack ◽  
Brushless Dc Motor ◽  
Bldc Motor ◽  
Motor Speed ◽  
Brushless Dc ◽  
Speed Controller ◽  
Optimum Speed ◽  
Control Scheme

<p>This paper presents a control scheme for speed control system in brushless dc (BLDC) motor to be utilized for electric motorbike. While conventional motorbikes require engine and fuel, electric motorbikes require DC motor and battery pack in order to be powered up. The limitation with battery pack is that it will need to be recharged after a certain period and distance. As the recharging process is time consuming, a PID controller is designed to maintain the speed of the motor at its optimum state, thus ensuring a longer lasting battery time (until the next charge). The controller is designed to track variations of speed references and stabilizes the output speed accordingly. The simulation results conducted in MATLAB/SIMULINK® shows that the motor, equipped with the PID controller was able to track the reference speed in 7.8x10<sup>-2</sup> milliseconds with no overshoot.  The result shows optimistic possibility that the proposed controller can be used to maintain the speed of the motor at its optimum speed.</p>

scholarly journals Constant Current Models of Brushless DC Motor

2013 ◽  
Vol 3 (1) ◽  
pp. 19-24 ◽  
Author(s):  
Krzysztof Krykowski ◽  
Janusz Hetmańczyk
Keyword(s):  
Current Model ◽  
Dc Motor ◽  
Constant Current ◽  
Brushless Dc Motor ◽  
Bldc Motor ◽  
Modified Model ◽  
Brushless Dc ◽  
Mathematical Equations ◽  
The Impact ◽  
Electronic Commutator

Abstract Two constant current models of Permanent Magnet Brushless Direct Current Motor (PM BLDC) are presented in the paper. In the first part of the paper principle of operation, basic properties and mathematical equations describing PM BLDC models are given. Then, two different constant current models of PM BLDC motor are considered: In the first model, PM BLDC motor is approximated with dc motor; in the second model, modified constant current model is applied with additional block, which is used to take into account the impact of inductance on torque-speed characteristics. In order to verify these models, torque-speed characteristics have been determined and compared for different motor supply voltages. After running a series of simulation and laboratory tests, we have found that this modified model (which makes allowance for the influence of inductance on torque-speed characteristics) ensures obtaining torque-speed characteristics identical to those of the real motor. Therefore, this model may be recommended for those simulation tests which do not consider effects occurring inside the electronic commutator-motor circuit. However, approximation of PM BLDC motor with dc motor is not recommended in computer tests.

Sign in / Sign up

Export Citation Format

Share Document