scholarly journals Structural performance of textile reinforced concrete sandwich panels under axial and transverse load

2021 ◽  
Vol 60 (1) ◽  
pp. 64-79
Author(s):  
Junqing Hong ◽  
Shaofeng Zhang ◽  
Hai Fang ◽  
Xunqian Xu ◽  
Honglei Xie ◽  
...  
Keyword(s):  
Reinforced Concrete ◽  
Bearing Capacity ◽  
Failure Modes ◽  
Ultimate Load ◽  
Wire Mesh ◽  
Transverse Load ◽  
Composite Panels ◽  
Textile Reinforced Concrete ◽  
Load Bearing Capacity ◽  
Load Bearing

Abstract The performance of textile reinforced concrete composite panels (TRCCPs) under the action of pseudo-static load up to collapse was evaluated. The test of TRCCPs under axial and transverse loading was conducted, and the results were compared with those for steel wire mesh reinforced-concrete composite panels (SMRCCPs). Ceram-site concrete was utilized as the panel matrix owing to its lightweight and insulation characteristics. The ultimate load bearing capacity, load-deformation and load-strain relationships, and failure modes were discussed and investigated in comparison with the findings of non-linear finite-element-model (FEM) analysis and the analytic method on the basis of the reinforced concrete (RC) theory. The analysis results indicate that TRCCP is suitable for use as a potential structural member for a wall or slab system of buildings, and the typical RC theory can be applied to predict the ultimate load bearing capacity if modified suitably.

Experimental Study on Residual Load Bearing Capacity of SRC Eccentric Columns after Exposure to Fire

2010 ◽  
Vol 163-167 ◽  
pp. 2240-2246 ◽  
Author(s):  
Jun Hua Li ◽  
Yue Feng Tang ◽  
Ming Zhe Liu
Keyword(s):  
Mechanical Properties ◽  
Reinforced Concrete ◽  
Bearing Capacity ◽  
Ultimate Strength ◽  
Room Temperature ◽  
Ultimate Load ◽  
Flexural Rigidity ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Steel Reinforced Concrete

This paper provided three test data pertaining to the mechanical properties of steel reinforced concrete (SRC) eccentric columns after exposure to fire and one comparative test data pertaining to the mechanical properties of steel reinforced concrete columns at room temperature. The influence of eccentricity on failure mode, distortion performance and ultimate load bearing capacity are mainly studied. Test results show that the failure modes of steel reinforced concrete eccentric columns after exposure to fire are similar to that at room temperature. Strain along the section height at mid-span section of eccentric columns before loaded to 90% ultimate load bearing capacity is linearly distributed and well agree with the plane section supposition. After exposure to fire, the flexural rigidity and load bearing capacity of specimens are all declined compared with that at normal temperature. In various loading stages from the initial loading to 80% ultimate strength, the ratio of flexural rigidity of SRC eccentric columns after exposure to fire and at normal temperature is ranged from 0.30 to 0.59. With the same concrete strength and heating condition, the ultimate strength of specimens decreases with the increasing of eccentricity. The ultimate bearing capacity of all specimens at normal room temperature is calculated on the method proposed by Chinese regulation JGJ 138-2001. The compared results of experimental values and calculating values show that the residual load bearing capacity of SRC eccentric columns after exposure to fire is about 69% to 81% of that at room temperature.

Experimental Study on the Mechanical Properties of Reinforced Concrete Columns after Exposure to Fire

2011 ◽  
Vol 243-249 ◽  
pp. 5122-5127
Author(s):  
Jia Feng Xu ◽  
Ming Zhe Liu ◽  
Yue Feng Tang
Keyword(s):  
Mechanical Properties ◽  
Reinforced Concrete ◽  
Bearing Capacity ◽  
Failure Mode ◽  
Room Temperature ◽  
Ultimate Load ◽  
Concrete Columns ◽  
Load Bearing Capacity ◽  
Reinforced Concrete Columns ◽  
Load Bearing

This paper provided three test data pertaining to the mechanical properties of reinforced concrete columns after exposure to ISO834 standard fire and three comparative test data pertaining to the mechanical properties of reinforced concrete columns at room temperature, mainly concerning the influence of fire on failure mode, distortion performance and ultimate load bearing capacity of reinforced concrete columns under axial and eccentric compression. Test results show that the failure mode of reinforced concrete columns after exposure to fire is basically same with that at room temperature. With the same concrete strength and heating condition, the bearing capacity of specimens reduces as the eccentricity increases. Strain along the section height of eccentric columns after fire basically agree with the plane section supposition while the flexural rigidity and ultimate load bearing capacity decreases obviously. The residual load bearing capacity of reinforced concrete columns after exposure to fire is only about 25% to 37% of that at room temperature.

The Load-Bearing Capacity of Aluminum Alloy T-Stub Joints

2011 ◽  
Vol 261-263 ◽  
pp. 765-769 ◽  
Author(s):  
Han Xu ◽  
Xiao Nong Guo ◽  
Yong Feng Luo
Keyword(s):  
Aluminum Alloy ◽  
Bearing Capacity ◽  
Parametric Analysis ◽  
Failure Modes ◽  
Ultimate Load ◽  
Numerical Results ◽  
Effective Length ◽  
Geometrical Parameters ◽  
Load Bearing Capacity ◽  
Load Bearing

The application of Aluminum alloy T-stub joints has been found widely in China recently, while the research achievements of the joint are far from adequate for design. This paper is focused on the ultimate load-bearing capacity of aluminum alloy T-stub joints. On the basis of Kulak prying model, formulas for calculating ultimate load-bearing capacity, considering four types of failure modes, are derived. The numerical simulation is carried out by means of ABAQUS FEA. Numerical results are verified by comparing with previous results obtained from experimental analysis. A parametric analysis is performed to investigate the influence of several geometrical parameters on the behavior of aluminum alloy T-stub joints including failure modes, ultimate load-bearing capacity and effective length of flanges. These numerical results are also compared with those calculated by relevant formulas in EC9.

scholarly journals MECHANICAL BEHAVIOUR OF TIMBER‐TO‐CONCRETE CONNECTIONS WITH INCLINED SCREWS

2007 ◽  
Vol 13 (3) ◽  
pp. 201-207 ◽  
Author(s):  
Saulius Kavaliauskas ◽  
Audronis Kazimieras Kvedaras ◽  
Balys Valiūnas
Keyword(s):  
Bearing Capacity ◽  
Failure Modes ◽  
Ultimate Load ◽  
Strength Properties ◽  
High Tensile Strength ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Plastic Failure ◽  
Axial Tension ◽  
Concrete Joints

The purpose of this paper is to adopt the Johansen's yielding theory as a possibility to predict the ultimate load for timber‐to‐concrete joints using self‐tapping threaded connectors screwed at an angle into the wood. The ultimate load‐bearing capacity of a single connector is predicted to be when either the stresses in the wood reach the plastic failure stress level or when a combination of plastic failure in wood and dowel is attained. K. W. Johansen assumed that no axial tension occurred in the dowel and, thus no frictional contribution affected the lateral load‐bearing capacity. However, the joints with inclined fasteners are first affected by tension load, so the withdrawal capacity of the screws has to be taken into account. In order to determine the load bearing capacity for specific connector geometry, the kinematical possible failure modes are determined. The screw in the concrete part of connection was taken as rigidly embedded and thus no deformations appeared. The study showed that the load‐bearing capacity for connections with inclined high tensile strength screws can be predicted using the yielding theory, but this theory was unable to predict precisely the failure mode. Possible reasons for that include limited fastener ductility and influence of the screw inclination on the strength properties of timber.

Numerical Simulation on Ultimate Bearing Capacity of FRP Reinforced Concrete Notched Beams

2010 ◽  
Vol 452-453 ◽  
pp. 337-340
Author(s):  
Pei Xiu Xia ◽  
Guang Ping Zou ◽  
Jie Lu
Keyword(s):  
Numerical Simulation ◽  
Reinforced Concrete ◽  
Bearing Capacity ◽  
Fracture Mechanism ◽  
Failure Modes ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Three Point Bending ◽  
Extreme Load ◽  
Simulation Results

: In this research, some concrete three-point bending specimens (beams) reinforced by FRP are used in numerical simulation to study the influence of the reinforcement on fracture mechanism and the extreme load-bearing capacity of the specimens. The numerical simulation results show the propagation of the crack in concrete is controlled by using FRP. Meanwhile the load-bearing capacity is increased greatly and failure modes are changed.

An Analysis of the Ultimate Load Bearing Capacity of Reinforced Concrete Arch Bridges

2004 ◽  
Vol 88 (6) ◽  
pp. 461-466
Author(s):  
Hua Zhao ◽  
Xudong Shao ◽  
Guangdong Liu ◽  
Mingxian Cheng ◽  
Ping Zhu
Keyword(s):  
Reinforced Concrete ◽  
Bearing Capacity ◽  
Ultimate Load ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Arch Bridges

Analysis of Ultimate Load-Bearing Capacity of Long-Span CFST Arch Bridges

2011 ◽  
Vol 90-93 ◽  
pp. 1149-1156 ◽  
Author(s):  
Yang Liu ◽  
Da Wang ◽  
Yi Zhou Zhu
Keyword(s):  
Bearing Capacity ◽  
Failure Modes ◽  
Ultimate Load ◽  
Elastic Buckling ◽  
Load Bearing Capacity ◽  
Finite Element Program ◽  
Load Bearing ◽  
Linear Elastic ◽  
Long Span ◽  
Element Program

In order to study the ultimate load-bearing capacity of the long-span concrete-filled steel tubular (CFST) arch bridge with fly-bird-type, the ANSYS finite element program was used to establish its special model, and to study ultimate load-bearing capacity of this bridge with three different methods. The constitutive relation factors of concrete-filled steel tubular was taken into consideration including confining effect ultimate load coefficients, failure modes, and load-displacement curves of this bridge under different cases. The result indicate that the ultimate load-bearing capacity of the bridge can meet the requirement, all of its failure modes is out-plane, the two methods, linear elastic buckling analysis and only geometric nonlinearity analysis, will over high estimate ultimate load-bearing capacity of this bridge, and linear elastic buckling method cannot reflect real failure mode of this structure. In order to correctly estimate the ultimate load-bearing capacity of the bridge structure, the effect of geometric and material double nonlinearity couldn’t be neglected.

Sign in / Sign up

Export Citation Format

Share Document