scholarly journals Simulation and characterization of planar high-efficiency back contact silicon solar cells

2021 ◽  
Vol 24 (3) ◽  
pp. 319-327
Author(s):  
A.V. Sachenko ◽  
◽  
V.P. Kostylyov ◽  
R.M. Korkishko ◽  
V.M. Vlasiuk ◽  
...  
Keyword(s):  
Solar Cells ◽  
High Efficiency ◽  
Short Circuit ◽  
Surface Recombination ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Back Contact ◽  
Planar Surfaces ◽  
High Efficiency Solar Cells

Short-circuit current, open-circuit voltage, and photoconversion efficiency of silicon high-efficiency solar cells with all back contact (BCSC) with planar surfaces have been calculated theoretically. In addition to the recombination channels usually considered in this kind of modeling, namely, radiative, Auger, Shockley–Read–Hall, and surface recombination, the model also takes into account the nonradiative trap-assisted exciton Auger recombination and recombination in the space charge region. It is ascertained that these two recombination mechanisms are essential in BCSCs in the maximum power operation regime. The model results are in good agreement with the experimental results from the literature.

17.8%-efficient Amorphous Silicon Heterojunction Solar Cells on p-type Silicon Wafers

2006 ◽  
Vol 910 ◽  
Author(s):  
Qi Wang ◽  
Matt P. Page ◽  
Eugene Iwancizko ◽  
Yueqin Xu ◽  
Yanfa Yan ◽  
...  
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Amorphous Silicon ◽  
High Efficiency ◽  
Short Circuit ◽  
Open Circuit ◽  
Layer Growth ◽  
Surface Recombination Velocity ◽  
Back Contact ◽  
P Type

AbstractWe have achieved an independently-confirmed 17.8% conversion efficiency in a 1-cm2, p-type, float-zone silicon (FZ-Si) based heterojunction solar cell. Both the front emitter and back contact are hydrogenated amorphous silicon (a-Si:H) deposited by hot-wire chemical vapor deposition (HWCVD). This is the highest reported efficiency for a HWCVD silicon heterojunction (SHJ) solar cell. Two main improvements lead to our most recent increases in efficiency: 1) the use of textured Si wafers, and 2) the application of a-Si:H heterojunctions on both sides of the cell. Despite the use of textured c-Si to increase the short-circuit current, we were able to maintain the same 0.65 V open-circuit voltage as on flat c-Si. This is achieved by coating a-Si:H conformally on the c-Si surfaces, including covering the tips of the anisotropically-etched pyramids. A brief atomic H treatment before emitter deposition is not necessary on the textured wafers, though it was helpful in the flat wafers. It is essential to high efficiency SHJ solar cells that the emitter grows abruptly as amorphous silicon, instead of as microcrystalline or epitaxial Si. The contact on each side of the cell comprises a thin (< 5 nm) low substrate temperature (~100°C) intrinsic a-Si:H layer, followed by a doped layer. Our intrinsic layers are deposited at 0.3-1.2 nm/s. The doped emitter and back-contact layers were deposited at a higher temperature (>200°C) and grown from PH3/SiH4/H2 and B2H6/SiH4/H2 doping gas mixtures, respectively. This combination of low (intrinsic) and high (doped layer) growth temperatures was optimized by lifetime and surface recombination velocity measurements. Our rapid efficiency advance suggests that HWCVD may have advantages over plasma-enhanced (PE) CVD in fabrication of high-efficiency heterojunction c-Si cells; there is no need for process optimization to avoid plasma damage to the delicate, high-quality, Si wafers.

The Effect of Al-BSF on Seff and Rb in Industrialized Mono-Silicon Solar Cells

2012 ◽  
Vol 472-475 ◽  
pp. 1846-1850
Author(s):  
Shan Shan Dai ◽  
Gao Jie Zhang ◽  
Xiang Dong Luo ◽  
Jing Xiao Wang ◽  
Wen Jun Chen ◽  
...  
Keyword(s):  
Solar Cells ◽  
Spectral Response ◽  
Short Circuit ◽  
Rear Surface ◽  
Surface Recombination ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Surface Recombination Velocity ◽  
Silicon Solar Cells ◽  
Back Surface

In this work, the effect of aluminum back surface field formed by screen printed various amount of Al paste on the effective rear surface recombination velocity (Seff) and the internal rear reflectance coeffeicient (Rb) of commercial mono-silicon solar cells was investigated. We demonstrated the effect of Seffand Rbon the performance of Al-BSF solar cells by simulating them with PC1D. The simulated results showed that the lower Seffcould get higher open circuit voltage (Voc), at the same time, the larger Rbcould get higher short-circuit current (Isc). Experimentally, we investigated the Seffand Rbthrough depositing Al paste with various amount (3.7, 5, 6, and 8 mg/cm2) for fabricating Al-BSF mono-silicon solar cells. Four group cells were characterized by light I-V, spectral response, hemispherical reflectance and scanning electron microscope (SEM) measurements. It was found that, a minimum Seffof 350 cm/s was gotten from the cells with Al paste of 8 mg/cm2, which was extracted by matching quantum efficiency (QE) from 800 nm to 1200 nm with PC1D, and a maximum Rbof 53.5% was obtained from Al paste of 5 mg/cm2by calculating at 1105 nm with PC1D. When the amount of Al paste was higher than 5mg/cm2, there were less Seffand lower Rb. On the other hand, when Al amount was 3.7mg/cm2, it was too little to form a closed BSF. Based on the SEM graphs and simulations with PC1D, a simple explaination was proposed for the experimental results.

Simulation of InAIN/Si Single-Heterojunction Solar Cells Using wxAMPS

2014 ◽  
Vol 665 ◽  
pp. 111-114 ◽  
Author(s):  
Ying Huang ◽  
Xiao Ming Shen ◽  
Xiao Feng Wei
Keyword(s):  
Solar Cells ◽  
Fill Factor ◽  
High Efficiency ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Indium Content ◽  
Open Circuit ◽  
Heterojunction Solar Cells ◽  
Si Solar Cells

In this paper, InAlN/Si single-heterojunction solar cells have been theoretically simulated based on wxAMPS software. The photovoltaic parameters, such as open circuit voltage, short circuit current, fill factor and conversion efficiency were investigated with changing the indium content and thickness of n-InAlN layer. Simulation results show that the optimum efficiency of InAlN/Si solar cells is 23.1% under AM 1.5G spectral illuminations, with the indium content and thickness of n-InAlN layer are 0.65 and 600nm, respectively. The simulation would contribute to design and fabricate high efficiency InAlN/Si solar cells in experiment.

Effect of CdTe thickness reduction in high efficiency CdS/CdTe solar cells

2001 ◽  
Vol 668 ◽  
Author(s):  
Akhlesh Gupta ◽  
I. Matulionis ◽  
J. Drayton ◽  
A.D. Compaan
Keyword(s):  
Solar Cells ◽  
High Efficiency ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Cdte Film ◽  
Open Circuit ◽  
Thickness Reduction ◽  
X Ray Diffraction ◽  
Cell Parameters ◽  
Cdte Solar Cells

ABSTRACTHigh efficiency CdTe solar cells are typically grown with CdTe thicknesses from 3 to 15 μm, although the thickness required for 90% absorption of the incident irradiation at 800 nm is only ∼1 μm. In this paper, we present the effect of CdTe thickness reduction on the performance of CdS/CdTe solar cells in which both the CdS and CdTe films were grown by sputtering. We produced a series of cells with different CdTe thickness (from 0.5 to 3.0 μm), and held the CdS thickness and back-contact-processing constant. The effect of CdTe thickness reduction on the diffusion of CdS into CdTe was studied using optical absorption and x-ray diffraction techniques. Only slight decreases occur in open-circuit voltage, short-circuit current, and fill factor with decrease in CdTe film thickness to 1.0 μm. Almost 10% efficient cells were obtained with 1 μm CdTe. Below 1 μm, all cell parameters decrease more rapidly, including the red quantum efficiency.

scholarly journals Graded Carrier Concentration Absorber Profile for High Efficiency CIGS Solar Cells

2015 ◽  
Vol 2015 ◽  
pp. 1-9 ◽  
Author(s):  
Antonino Parisi ◽  
Riccardo Pernice ◽  
Vincenzo Rocca ◽  
Luciano Curcio ◽  
Salvatore Stivala ◽  
...  
Keyword(s):  
Solar Cells ◽  
Band Gap ◽  
Carrier Concentration ◽  
High Efficiency ◽  
Energy Gap ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Doping Density ◽  
Cigs Solar Cells

We demonstrate an innovative CIGS-based solar cells model with a graded doping concentration absorber profile, capable of achieving high efficiency values. In detail, we start with an in-depth discussion concerning the parametrical study of conventional CIGS solar cells structures. We have used the wxAMPS software in order to numerically simulate cell electrical behaviour. By means of simulations, we have studied the variation of relevant physical and chemical parameters—characteristic of such devices—with changing energy gap and doping density of the absorber layer. Our results show that, in uniform CIGS cell, the efficiency, the open circuit voltage, and short circuit current heavily depend on CIGS band gap. Our numerical analysis highlights that the band gap value of 1.40 eV is optimal, but both the presence of Molybdenum back contact and the high carrier recombination near the junction noticeably reduce the crucial electrical parameters. For the above-mentioned reasons, we have demonstrated that the efficiency obtained by conventional CIGS cells is lower if compared to the values reached by our proposed graded carrier concentration profile structures (up to 21%).

scholarly journals PREPARATION AND CHARACTERIZATION OF P3HT-PCBM ORGANIC SOLAR CELLS

2013 ◽  
pp. 23-25
Author(s):  
ANUBHAV GUPTA ◽  
PRAVEEN S ◽  
ABHISHEK KUMAR ◽  
PRIYANKA SHREE ◽  
SUCHANA MISHRA
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Active Layer ◽  
Organic Solar Cells ◽  
Silicon Solar Cell ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Glass Substrates

Organic solar cells using P3HT: PCBM as an active layer on ITO coated glass substrates were fabricated and characterized. Different air annealing procedures and cathode materials were tried and the characteristics were compared with that of a standard thin film polycrystalline silicon solar cell. It was found that the sample prepared with post-deposition air annealing at 130 oC improves the open circuit voltage (Voc) considerably. Besides, short circuit current (Isc) and the efficiency (η) were highest for the sample with a non annealed active layer. Series resistance (Rs) for this sample was lowest, but 103 times higher than that of the silicon solar cell, which in turn may have reduced the efficiency value for the organic cell compared to silicon.

Effects of Barrier Width on Spectral Response of Strained Layer Superlattices for High Efficiency Solar Cells

2009 ◽  
Vol 1211 ◽  
Author(s):  
Geoffrey K. Bradshaw ◽  
Conrad Zachary Carlin ◽  
Peter C. Colter ◽  
Jeffrey L. Harmon ◽  
Joshua P. Samberg ◽  
...  
Keyword(s):  
Solar Cells ◽  
High Efficiency ◽  
Spectral Response ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Zero Bias ◽  
Fully Depleted ◽  
Strained Layer ◽  
High Efficiency Solar Cells ◽  
Strained Layer Superlattices

AbstractCharacteristics of strained layer superlattices (SLS) consisting of alternating layers InxGa1-xAs and GaAs1-yPy are examined for use in high efficiency solar cells. The effects of SLS quantum barrier widths on tunneling probability and short circuit current are discussed through analysis of J-V and spectral response measurements. Results indicate a threshold barrier thickness for which tunneling effects are deleterious. Effect of the number of SLS periods incorporated into a p-i-n structure and maximum number of periods are presented through spectral response and CV analysis. It is demonstrated that SLS show increasing responsivity with increasing number of periods due to higher absorption. CV analysis is performed to determine zero bias depletion widths for verifying appropriate number of SLS periods and fully depleted SLS region.

scholarly journals Improving Efficiency of Evaporated Cu2ZnSnS4Thin Film Solar Cells by a Thin Ag Intermediate Layer between Absorber and Back Contact

2015 ◽  
Vol 2015 ◽  
pp. 1-9 ◽  
Author(s):  
Hongtao Cui ◽  
Chang-Yeh Lee ◽  
Wei Li ◽  
Xiaolei Liu ◽  
Xiaoming Wen ◽  
...  
Keyword(s):  
Solar Cells ◽  
Carrier Transport ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Depletion Region ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Back Contact ◽  
Secondary Phases ◽  
P Type

A 20 nm Ag coating on Mo back contact was adopted to improve the back contact of evaporated Cu2ZnSnS4(CZTS) solar cells. The Ag layer helped reduce the thickness of MoS2which improves fill factor (FF) significantly; additionally, it reduced secondary phases ZnS and SnS2−x, which may help carrier transport; it was also involved in the doping of the absorber layer, which compensated the intrinsic p-type doping and therefore drags down the doping level. The doping involvement may enlarge the depletion region and improve lifetime of the absorber, which led to enhancing open circuit voltage (VOC), short circuit current density (JSC), and efficiency significantly. However, it degrades the crystallinity of the material slightly.

scholarly journals ABX3 inorganic halide perovskites for solar cells: chemical and crystal structure stability

2021 ◽  
Vol 26 (4) ◽  
Author(s):  
Cristian Moisés Díaz-Acosta ◽  
Antonia Martínez-Luévanos ◽  
Sofía Estrada-Flores ◽  
Lucia Fabiola Cano-Salazar ◽  
Elsa Nadia Aguilera-González ◽  
...  
Keyword(s):  
Crystal Structure ◽  
Solar Cells ◽  
High Efficiency ◽  
Low Cost ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Structure Stability ◽  
Halide Perovskites ◽  
Halide Perovskite

ABSTRACT Solar energy is one of the most promising and developed technologies in recent years, due to its high efficiency and low cost. Perovskite-type solar cells have been the focus of attention by the world scientific community. The main objective of this article is to present an (PSCs) analysis of the various investigations reported on the development of ABX3 inorganic halide perovskite-based solar cells, with emphasis in the effect that temperature and humidity have on their chemical and crystal structure stability. The main methods that are used to obtain ABX3 inorganic halide perovskites are also presented and analyzed. An analysis about the structure of these photovoltaic cells and how to improve their efficiency (PCS), fill factor (FF), short circuit current density (Jsc) and open circuit voltage (Voc) of these devices is presented. As a conclusion, a relationship of the methods, synthesis variables, and type of inorganic halide perovskite used for the development of devices with the best efficiencies is presented; the trends towards which this area of science is heading are also highlighted.

Sign in / Sign up

Export Citation Format

Share Document