scholarly journals Ultra-large Specific Surface Area Activated Carbon Synthesized from Rice Husk with High Adsorption Capacity for Methylene Blue

2020 ◽  
pp. 632
Author(s):  
Fan ZHOU ◽  
Hui BI ◽  
Fuqiang HUANG
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Specific Surface ◽  
Adsorption Capacity ◽  
Surface Area ◽  
Specific Surface Area ◽  
Rice Husk ◽  
Large Specific Surface Area ◽  
High Adsorption ◽  
High Adsorption Capacity

Study of the Porous Structure and High Adsorption Capacity of Biomass-Based Activated Carbon Prepared from Aspen Wood by Ferric Nitrate III Activation

2021 ◽  
Vol 15 (2) ◽  
pp. 131-144
Author(s):  
Chunjiang Jin ◽  
Huimin Chen ◽  
Luyuan Wang ◽  
Xingxing Cheng ◽  
Donghai An ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Specific Surface ◽  
Adsorption Capacity ◽  
Surface Area ◽  
Specific Surface Area ◽  
Pore Volume ◽  
Mass Ratio ◽  
Aspen Wood ◽  
Surface Functional Groups ◽  
Wood Sawdust

In this study, aspen wood sawdust was used as the raw material, and Fe(NO3)3 and CO2 were used as activators. Activated carbon powder (ACP) was produced by the one-step physicochemical activation method in an open vacuum tube furnace. The effects of different mass ratios of Fe(NO3)3 and aspen wood sawdust on the pore structure of ACP were examined under single-variable experimental conditions. The mass ratio was 0–0.4. The detailed characteristics of ACP were examined by nitrogen adsorption, scanning electron microscopy, X-ray diffraction, and Fourier transform infrared spectroscopy. The adsorption capacity of ACP was established by simulating volatile organic compounds (VOCs) using ethyl acetate. The results showed that ACP has a good nanostructure with a large pore volume, specific surface area, and surface functional groups. The pore volume and specific surface area of Fe-AC-0.3 were 0.26 cm3/g and 455.36 m2/g, respectively. The activator played an important role in the formation of the pore structure and morphology of ACP. When the mass ratio was 0–0.3, the porosity increased linearly, but when it was higher than 0.3, the porosity decreased. For example, the pore volume and specific surface area of Fe-AC-0.4 reached 0.24 cm3/g and 430.87 m2/g, respectively. ACP presented good VOC adsorption performance. The Fe-AC-0.3 sample, which contained the most micropore structures, presented the best adsorption capacity for ethyl acetate at 712.58 mg/g. Under the action of the specific reaction products nitrogen dioxide (NO2) and oxygen, the surface of modified ACP samples showed different rich C/O/N surface functional groups, including C-H, C=C, C=O, C-O-C, and C-N.

scholarly journals Investigation of Nickel Ion Removal by Means of Activated Clay

1992 ◽  
Vol 9 (4) ◽  
pp. 244-257 ◽  
Author(s):  
S. Hawash ◽  
J.Y. Farah ◽  
M.S. El-Geundi
Keyword(s):  
Activated Carbon ◽  
Economic Analysis ◽  
Specific Surface ◽  
Adsorption Capacity ◽  
Surface Area ◽  
Specific Surface Area ◽  
Wastewater Analysis ◽  
Natural Clay ◽  
Nickel Ion ◽  
Ion Removal

Natural and activated clays have been investigated as adsorbents for the removal of nickel from wastewater. Analysis of the natural clay under test showed that it was composed, approximately of 51% kaolinite, 46% montmorillonite and 3% illite, having a specific surface area of 65 m2/g. The natural clay was treated with different activators (HCl, NaCl and H2O2) to enhance its adsorption capacity towards nickel. The efficiency of such activation was greater by 16.0% and 23.2% in the case of NaCl and H2O2, respectively, relative to untreated clay. No significant increase in the adsorption capacity was brought about by HCl treatment. A limited comparison has been made between clay and activated carbon by performing isotherm studies under similar conditions. The results indicate that the adsorption capacity of clay activated with H2O2, clay activated with NaCl and natural clay is 216.9%, 204.2% and 176.1% that of activated carbon, respectively. Based solely on the adsorption capacity, an economic analysis demonstrates that natural clay is the cheapest material, followed by clay activated with NaCl and clay activated with H2O2. The relative costs of removing nickel using natural clay, clay activated with NaCl and clay activated with H2O2 were found to be 2.8%, 5.4% and 25.4%, respectively, that of activated carbon.

scholarly journals Coconut-based activated carbon fibers for efficient adsorption of various organic dyes

RSC Advances ◽  
2018 ◽  
Vol 8 (74) ◽  
pp. 42280-42291 ◽  
Author(s):  
Ling Zhang ◽  
Ling-yu Tu ◽  
Yan Liang ◽  
Qi Chen ◽  
Ze-sheng Li ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Carbon Fibers ◽  
Organic Dyes ◽  
Low Cost ◽  
Micropore Volume ◽  
Activated Carbon Fibers ◽  
Large Specific Surface Area

Activated carbon fibers with high micropore volume and large specific surface area were prepared from abundant and low-cost coconut fibers, which show excellent adsorption performances towards various dyes.

Preparation and Characterization of Microporous Activated Carbon from Raw Petroleum Cokes

2015 ◽  
Vol 814 ◽  
pp. 286-291
Author(s):  
Bo Tao Wang
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Specific Surface ◽  
Pore Size Distribution ◽  
Pore Size ◽  
Surface Area ◽  
Specific Surface Area ◽  
High Specific Surface Area ◽  
Activation Time ◽  
Activation Temperature

Adopting the chemical activation method, the high specific surface area activated carbon (AC) was prepared by the solid mixing method using Daqing petroleum cokes as raw materials and KOH as activator. The influence of the ratio of KOH to carbon, activation temperature and activation time on the iodine and methylene blue adsorption properties of the AC were studied. The micro-graphitic structure of the AC was studied by X-ray diffraction (XRD). The BET specific surface area, BJH pore size distribution and pore volume of the AC were determined by N2 adsorption (at 77K). The experimental results show that the high specific surface area AC can be prepared with the ratio of KOH to carbon of 4, activation temperature of 800°C and activation time of 1h. The specific surface area was as high as 2142 m2/g with the iodine adsorption value of 288mg/g and methylene blue adsorption value of 1266mg/g. The XRD and BJH results also show that amorphous carbon was the dominating form, and the pore size distribution represents micropore structure.

Guanidine sulfate-assisted synthesis of hexagonal WO3 nanoparticles with enhanced adsorption properties

2015 ◽  
Vol 44 (16) ◽  
pp. 7419-7427 ◽  
Author(s):  
Wanjun Mu ◽  
Mei Li ◽  
Xingliang Li ◽  
Zongping Ma ◽  
Rui Zhang ◽  
...  
Keyword(s):  
Specific Surface ◽  
Adsorption Capacity ◽  
Surface Area ◽  
Functional Groups ◽  
Specific Surface Area ◽  
Adsorption Properties ◽  
Large Specific Surface Area ◽  
Enhanced Adsorption

The hexagonal WO3 nanowires prepared with the assistance of C2H10N·H2SO4 possess a large specific surface area and numerous adsorption functional groups, consequently improving the Sr2+ adsorption capacity considerably.

Elimination of Dyes Present in Textile Industry Wastewater Using Adsorbent Materials Prepared from Broccoli Stem

2014 ◽  
Vol 976 ◽  
pp. 207-211 ◽  
Author(s):  
Alejandra Alicia Peláez Cid ◽  
Araceli Vázquez Barranco ◽  
Ana María Herrera González
Keyword(s):  
Activated Carbon ◽  
Specific Surface ◽  
Adsorption Capacity ◽  
Surface Area ◽  
Specific Surface Area ◽  
Sodium Acrylate ◽  
Anionic Dyes ◽  
Vat Dyes ◽  
Textile Effluents ◽  
Adsorbent Materials

This paper presents the results of the adsorption of textile dyes in static systems, using adsorbent materials prepared from broccoli waste collected after harvest. The adsorption capacities of the non-activated lignocellulosic residue (BrocNat), the chemically activated waste using sodium hydroxide (BrocNaOH), the thermally activated at 823 K ash (AshBroc), and the chemically activated carbon using phosphoric acid at 673 K (CarBrocQ) were tested. Aqueous solutions containing cationic and anionic dyes as well as textile effluents generated after the dyeing process of a cotton-processing factory containing vat and reactive dyes were treated. Lignocellulosic materials were only effective in removing dyes when they were found in aqueous solution. The carbonaceous adsorbent CarBrocQ presented removal percentages close to 100% and between 13 and 75% for reactive and vat dyes contained in the effluents respectively. To accomplish the complete elimination of color from effluents containing vat dyes, these were treated before adsorption, using aluminum chlorohydrate and poly(acrylamide-co-sodium acrylate) as coagulant and flocculant agents, respectively. The COD of the effluent containing vat dyes was reduced up to 93% after both treatments were combined, and the removal of color was absolute. The high adsorption capacity of CarBrocQ occurs because of its high specific surface area, which was determined by N2 adsorption to be 1177 m2g-1. In the case of the lignocellulosic material, the specific surface area was determined by means of adsorption of methylene blue, and it was 485 m2g-1 for both. The adsorption capacity of CarBrocQ was compared with that of commercial carbons, and proved to be similar. The adsorption results obtained indicate that broccoli waste can be used to prepare activated carbon with applications in the removal of dyes present in textile effluents.

scholarly journals High Level Oxygen Reduction Catalysts Derived from the Compounds of Large Specific Surface Area Pine Peel Activated Carbon and Phthalocyanine Cobalt

2021 ◽  
Author(s):  
Lei Zhao ◽  
Ziwei Lan ◽  
Junyu Su ◽  
Huazhu Liang ◽  
Jiayu Yao ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Active Sites ◽  
High Performance ◽  
Metal Catalysts ◽  
Large Specific Surface Area ◽  
Composite Catalysts ◽  
Nonprecious Metal

Compared with precious metal catalysts, non-platinum catalysts have the advantages of low cost and high performance. Among them, the activated carbon (AC) with a large specific surface area (SSA) can be used as a carrier or as a carbon source of nonprecious metal/carbon system catalyst at the same time. Therefore, this paper uses cheap pine peel bio-based materials to prepare large surface area activated carbon and then compound with cobalt phthalocyanine (CoPc) to obtain a high-performance cobalt/nitrogen/carbon catalyst. The merits include AC@CoPc composite catalysts are prepared by precisely controlling the composite proportion of AC and CoPc, the atomically dispersed Co nanoparticles form and synergistically with N promote the exposure of CoNx active sites, and the Eonset of the catalyst treated with a composite proportion of AC and CoPc of 1 to 2 at 800 °C (AC@CoPc-800-1-2) is 1.01 V, which is higher than Pt/C (20 wt%) catalyst. Apart from this, the stability is 87.8% in 0.1 M KOH after 20000 s testing in compared with other AC@CoPc series catalysts and Pt/C (20 wt%) catalyst. Considering from the performance and price of the catalyst in practical application, these composite catalysts combine biomass carbon materials with phthalocyanine series, which will be widely used in the area of nonprecious metal catalysts.

Sign in / Sign up

Export Citation Format

Share Document