Motional finite element simulation of a single-phase induction motor

2009 ◽  
Vol 4 (2) ◽  
pp. 57-66 ◽  
Author(s):  
Dániel Marcsa ◽  
Miklós Kuczmann
Keyword(s):  
Finite Element ◽  
Finite Element Simulation ◽  
Induction Motor ◽  
Single Phase ◽  
Element Simulation

A Comparative Study of Single-Phase AC and Multiphase DC Resistance Spot Welding

2004 ◽  
Vol 127 (3) ◽  
pp. 583-589 ◽  
Author(s):  
Wei Li ◽  
Daniel Cerjanec ◽  
Gerald A. Grzadzinski
Keyword(s):  
Finite Element ◽  
Comparative Study ◽  
Simulation Model ◽  
Finite Element Simulation ◽  
Resistance Spot Welding ◽  
Spot Welding ◽  
Single Phase ◽  
Welding Process ◽  
Welding Current ◽  
Element Simulation

This paper presents a comparative study of the AC and MFDC resistance spot welding process. Both experiments and finite element simulation were conducted to compare the weld size and energy consumption. The experiments were performed on two identical spot welding machines, one with a single phase ac and the other with a mid-frequency DC weld control. The machines were instrumented such that both the primary and secondary voltage and current signals could be collected for energy calculation. The finite element simulation model was developed to understand the underlying mechanisms of the difference between the ac and MFDC processes. The effect of the current waveform was investigated by using the actual process measurements as an input to the simulation model. It is shown that the MFDC process generally produces larger welds than the AC process with the same root-mean-square welding current. However, this difference is more prominent when the welding current is relatively low. Overall, the AC welding process consumes more energy to make a same sized weld than the MFDC process. The larger the welding current is used, the less efficient the AC welding process will become. The differences between the two welding processes are caused by the contact resistance behavior and the electrical inductance in the AC welding process.

Finite Element Simulation of Tire-Rim Interface

1989 ◽  
Vol 17 (4) ◽  
pp. 305-325 ◽  
Author(s):  
N. T. Tseng ◽  
R. G. Pelle ◽  
J. P. Chang
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Finite Element Simulation ◽  
Contact Pressure ◽  
Element Model ◽  
Experimental Measurements ◽  
Inflation Pressure ◽  
Interference Fit ◽  
Element Simulation ◽  
Rubber Composite

Abstract A finite element model was developed to simulate the tire-rim interface. Elastomers were modeled by nonlinear incompressible elements, whereas plies were simulated by cord-rubber composite elements. Gap elements were used to simulate the opening between tire and rim at zero inflation pressure. This opening closed when the inflation pressure was increased gradually. The predicted distribution of contact pressure at the tire-rim interface agreed very well with the available experimental measurements. Several variations of the tire-rim interference fit were analyzed.

Numerical Simulation of Tire Sliding Events Involving Impacts with Holes and Bumps

1986 ◽  
Vol 14 (2) ◽  
pp. 125-136 ◽  
Author(s):  
Y. Nakajima ◽  
J. Padovan
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Finite Element Simulation ◽  
Full Range ◽  
Arbitrary Geometry ◽  
Operating Environments ◽  
Element Simulation ◽  
Simulation Scheme

Abstract This paper extends the finite element simulation scheme to handle the problem of tires undergoing sliding (skidding) impact into obstructions. Since the inertial characteristics are handled by the algorithm developed, the full range of operating environments can be accommodated. This includes the treatment of impacts with holes and bumps of arbitrary geometry.

Sign in / Sign up

Export Citation Format

Share Document