Microstructure and Properties of Nanosemicrystalline Si3N4 Ceramics with Doped Sintering Additives: Part I. Microstructural Characterization of Nanosemicrystalline Si3N4 Powders

1998 ◽  
Vol 13 (9) ◽  
pp. 2580-2587 ◽  
Author(s):  
K. H. Ryu ◽  
J-M. Yang
Keyword(s):  
Microstructural Characterization ◽  
Degree Of Crystallinity ◽  
Chemical Compositions ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sintering Additives ◽  
Transmission Electron ◽  
Wet Chemical ◽  
Si3n4 Ceramics

The characteristics of nanosized silicon nitride powders with doped Y2O3 and Al2O3 fabricated by a plasma-reacted chemical process were investigated. The chemical compositions of the powders were analyzed by wet chemical analysis. The morphology and the size distribution were determined by transmission electron microscopy (TEM). TEM with energy dispersive spectroscopy (EDS) was used to verify the existence of sintering additives in each individual particle. The crystal structure of the powders was identified by the selected area diffraction pattern (SADP). X-ray diffraction (XRD) technique was used for phase analysis and the measurement of degree of crystallinity. The characteristics of chemical bonding was analyzed by using Fourier transform infrared spectroscopy (FTIR).

scholarly journals Characterization of ferrite nanoparticles for preparation of biocomposites

2017 ◽  
Vol 8 ◽  
pp. 1257-1265 ◽  
Author(s):  
Urszula Klekotka ◽  
Magdalena Rogowska ◽  
Dariusz Satuła ◽  
Beata Kalska-Szostko
Keyword(s):  
Chemical Method ◽  
Ferrite Nanoparticles ◽  
Chemical Activity ◽  
Nominal Composition ◽  
X Ray Diffraction ◽  
Wet Chemical Method ◽  
X Ray ◽  
Transmission Electron ◽  
Wet Chemical

Ferrite nanoparticles with nominal composition Me0.5Fe2.5O4 (Me = Co, Fe, Ni or Mn) have been successfully prepared by the wet chemical method. The obtained particles have a mean diameter of 11–16 ± 2 nm and were modified to improve their magnetic properties and chemical activity. The surface of the pristine nanoparticles was functionalized afterwards with –COOH and –NH2 groups to obtain a bioactive layer. To achieve our goal, two different modification approaches were realized. In the first one, glutaraldehyde was attached to the nanoparticles as a linker. In the second one, direct bonding of such nanoparticles with a bioparticle was studied. In subsequent steps, the nanoparticles were immobilized with enzymes such as albumin, glucose oxidase, lipase and trypsin as a test bioparticles. The characterization of the nanoparticles was acheived by transmission electron microscopy, X-ray diffraction, energy dispersive X-ray and Mössbauer spectroscopy. The effect of the obtained biocomposites was monitored by Fourier transform infrared spectroscopy. The obtained results show that in some cases the use of glutaraldehyde was crucial (albumin).

Microstructural Characterization of a Fe-Based Compostie Reinforced by TiC

2011 ◽  
Vol 675-677 ◽  
pp. 835-838
Author(s):  
Jing Wang ◽  
Si Jing Fu ◽  
Hong Cheng
Keyword(s):  
Electron Microscope ◽  
Microstructural Characterization ◽  
Interfacial Structure ◽  
Synthesis Reaction ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Tic Particle ◽  
Scanning Electron

The present work reported the preparation of TiC/Fe-based composite by the synthesis reaction from Ti, C and Fe. The sintered composites were characterized by X-ray diffraction, scanning electron microscope and transmission electron microscope. TiC, Fe3C and α-Fe were detected by X-ray diffraction analysis. The scanning and transmission electron micrographs revealed the morphology and distribution of the reinforcements, the microstructure of Fe matrix, the interfacial structure of TiC particle-to-Fe matrix. Moreover, the formation reason of the voids in composite was also discussed.

Microstructural Characterization of In Situ Reaction TiB2/Zn-30Al-1Cu Composites Prepared by Spray Deposition Process

2014 ◽  
Vol 1015 ◽  
pp. 688-691 ◽  
Author(s):  
Feng Wang ◽  
Qiang Zhang ◽  
Bai Qing Xiong ◽  
Yong An Zhang ◽  
Hong Wei Liu ◽  
...  
Keyword(s):  
Spray Deposition ◽  
Microstructural Characterization ◽  
Deposition Process ◽  
Deposition Technique ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Electron

An innovative spray deposition technique has been applied to produce in situ TiB2/Zn-30Al-1Cu composites. The microstructures of the spray-deposited composite were studied using scanning electron microscopy, transmission electron microscope and X-ray diffraction. The results have shown that the TiB2particulates are formed in the microstructure. It was found that the TiB2particles were distributed in Zn-30Al-1Cu matrix uniformly, and the TiB2particles are about 2μm in size.

The Use of Advanced Analytical Techniques for Characterization of the Chemical, Physical, and Crystallographic Nature of a Surface

1973 ◽  
Vol 31 ◽  
pp. 132-133 ◽  
Author(s):  
R. E. Herfert
Keyword(s):  
Surface Characterization ◽  
Analytical Techniques ◽  
X Ray Diffraction ◽  
Depth Of Penetration ◽  
X Ray ◽  
The Past ◽  
Transmission Electron ◽  
Scanning Electron

Studies of the nature of a surface, either metallic or nonmetallic, in the past, have been limited to the instrumentation available for these measurements. In the past, optical microscopy, replica transmission electron microscopy, electron or X-ray diffraction and optical or X-ray spectroscopy have provided the means of surface characterization. Actually, some of these techniques are not purely surface; the depth of penetration may be a few thousands of an inch. Within the last five years, instrumentation has been made available which now makes it practical for use to study the outer few 100A of layers and characterize it completely from a chemical, physical, and crystallographic standpoint. The scanning electron microscope (SEM) provides a means of viewing the surface of a material in situ to magnifications as high as 250,000X.

scholarly journals New Insights into the Crystal Chemistry of Elpidite, Na2Zr[Si6O15]·3H2O and (Na1+YCax□1−X−Y)Σ=2Zr[Si6O15]·(3−X)H2O, and Ab Initio Modeling of IR Spectra

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2160
Author(s):  
Alexander Bogdanov ◽  
Ekaterina Kaneva ◽  
Roman Shendrik
Keyword(s):  
Ir Spectra ◽  
Structural Models ◽  
Chemical Characterization ◽  
Chemical Compositions ◽  
X Ray Diffraction ◽  
Special Group ◽  
X Ray ◽  
Influence Of Water ◽  
Radioactive Species

Elpidite belongs to a special group of microporous zirconosilicates, which are of great interest due to their capability to uptake various molecules and ions, e.g., some radioactive species, in their structural voids. The results of a combined electron probe microanalysis and single-crystal X-ray diffraction study of the crystals of elpidite from Burpala (Russia) and Khan-Bogdo (Mongolia) deposits are reported. Some differences in the chemical compositions are observed and substitution at several structural positions within the structure of the compounds are noted. Based on the obtained results, a detailed crystal–chemical characterization of the elpidites under study was carried out. Three different structure models of elpidite were simulated: Na2ZrSi6O15·3H2O (related to the structure of Russian elpidite), partly Ca-replaced Na1.5Ca0.25ZrSi6O15·2.75H2O (close to elpidite from Mongolia), and a hypothetical CaZrSi6O15·2H2O. The vibration spectra of the models were obtained and compared with the experimental one, taken from the literature. The strong influence of water molecule vibrations on the shape of IR spectra of studied structural models of elpidite is discussed in the paper.

Detonation Synthesis of Nano-Size Materials

1995 ◽  
Vol 418 ◽  
Author(s):  
J. Forbes ◽  
J. Davis ◽  
C. Wong
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Nucleation And Growth ◽  
Detonation Synthesis ◽  
X Ray Diffraction ◽  
Crystalline Materials ◽  
X Ray ◽  
Transmission Electron ◽  
Nano Size

AbstractThe detonation of explosives typically creates 100's of kbar pressures and 1000's K temperatures. These pressures and temperatures last for only a fraction of a microsecond as the products expand. Nucleation and growth of crystalline materials can occur under these conditions. Recovery of these materials is difficult but can occur in some circumstances. This paper describes the detonation synthesis facility, recovery of nano-size diamond, and plans to synthesize other nano-size materials by modifying the chemical composition of explosive compounds. The characterization of nano-size diamonds by transmission electron microscopy and electron diffraction, X-ray diffraction and Raman spectroscopy will also be reported.

One Step Synthesis and Characterization of Zirconia-Graphene Composites

2012 ◽  
Vol 600 ◽  
pp. 174-177 ◽  
Author(s):  
Jian Fei Xia ◽  
Zong Hua Wang ◽  
Yan Zhi Xia ◽  
Fei Fei Zhang ◽  
Fu Qiang Zhu ◽  
...  
Keyword(s):  
Synthesis And Characterization ◽  
Two Dimensional ◽  
X Ray Diffraction ◽  
X Ray ◽  
Graphene Composite ◽  
Transmission Electron ◽  
One Step ◽  
Ft Ir ◽  
Xrd Techniques

Zirconia-graphene composite (ZrO2-G) has been successfully synthesized via decomposition of ZrOCl2•6H2O in a water-isopropanol system with dispersed graphene oxide (GO) utilizing Na2S as a precursor could enable the occurrence of the deposition of Zr4+ and the deoxygenation of GO at the same time. Transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FT-IR) and X-ray diffraction (XRD) techniques were used to characterize the samples. It was found that graphene were fully coated with ZrO2, and the ZrO2 existing in tetragonal phase, which resulted in the formation of two-dimensional composite.

Hydrothermal Synthesis and Characterization of BiFeO3 Polyhedral Crystallites

2012 ◽  
Vol 174-177 ◽  
pp. 508-511
Author(s):  
Lin Lin Yang ◽  
Yong Gang Wang ◽  
Yu Jiang Wang ◽  
Xiao Feng Wang
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
Xrd Pattern ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Electron

BiFeO3 polyhedrons had been successfully synthesized via a hydrothermal method. The as-prepared products were characterized by power X-ray diffraction (XRD) pattern, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The possible mechanisms for the formation of BiFeO3 polyhedrons were discussed. Though comparison experiments, it was found that the kind of precursor played a key role on the morphology control of BiFeO3 crystals.

Influence of the Residue of Casting by Lost Wax in the Modulus of Elasticity and Porosity of Concretes

2014 ◽  
Vol 805 ◽  
pp. 343-349
Author(s):  
Carine F. Machado ◽  
Weber G. Moravia
Keyword(s):  
Construction Industry ◽  
Modulus Of Elasticity ◽  
Chemical Characterization ◽  
Microstructural Characterization ◽  
Cement Matrix ◽  
X Ray Diffraction ◽  
X Ray ◽  
Hardened State ◽  
Material Powder

This work evaluated the influence of additions of the ceramic shell residue (CSR), from the industries of Lost Wax Casting, in the modulus of elasticity and porosity of concrete. The CSR was ground and underwent a physical, chemical, and microstructural characterization. It was also analyzed, the environmental risk of the residue. In the physical characterization of the residue were analyzed, the surface area, and particle size distribution. In chemical characterization, the material powder was subjected to testing of X-ray fluorescence (XRF). Microstructural characterization was performed by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The residue was utilized like addition by substitution of cement in concrete in the percentages of 10% and 15% by weight of Portland cement. It was evaluated properties of concrete in the fresh and hardened state, such as compressive strength, modulus of elasticity, absorption of water by total immersion and by capillarity. The results showed that the residue can be used in cement matrix and improve some properties of concrete. Thus, the CSR may contribute to improved sustainability and benefit the construction industry.

Characterization of Al65.0Cu32.9Co2.1 Alloy Containing Nanofibres

2012 ◽  
Vol 186 ◽  
pp. 212-215
Author(s):  
Jacek Krawczyk ◽  
Włodzimierz Bogdanowicz ◽  
Grzegorz Dercz ◽  
Wojciech Gurdziel
Keyword(s):  
Electron Microscopy ◽  
Average Diameter ◽  
Chemical Compositions ◽  
X Ray ◽  
Transmission Electron ◽  
Orthogonal Set ◽  
T Phase ◽  
Terminal Area ◽  
Scanning Electron

Microstructure of terminal area of Al65Cu32.9Co2.1ingots (numbers indicate at.%), obtained via directional solidification was studied. Scanning Electron Microscopy, Transmission Electron Microscopy and X-ray powder diffraction were applied. Point microanalysis by Scanning Electron Microscope was used for examination of chemical compositions of alloy phases. It was found that tetragonal θ phase of Al2Cu stoichiometric formula was the dominate phase (matrix). Additionally the alloy contained orthogonal set of nanofibres of Al7Cu2Co T phase with the average diameter of 50-500 nm and oval areas of hexagonal Al3(Cu,Co)2H-phase, surrounded by monoclinic AlCu η1phase rim. Inside some areas of H-phase cores of decagonal quasicrystalline D phase were observed.

Sign in / Sign up

Export Citation Format

Share Document