Characterization of 14YWT As-Atomized, Milled, Milled and Annealed Powders and HIP Consolidated Alloys

2011 ◽  
Vol 1298 ◽  
Author(s):  
Nicholas J. Cunningham ◽  
Auriane Etienne ◽  
G. Robert Odette ◽  
Erich Stergar ◽  
Yuan Wu ◽  
...  
Keyword(s):  
Best Practice ◽  
Atom Probe ◽  
Precipitate Size ◽  
Dispersion Strengthening ◽  
Mechanically Alloyed ◽  
Transmission Electron ◽  
Annealed Powder ◽  
Attritor Milling ◽  
Ultrahigh Density ◽  
Rapidly Solidified

ABSTRACTNanostructured ferritic alloys (NFA) are Fe-Cr based ferritic stainless steels containing an ultrahigh density of very stable Y-Ti-O nanofeatures (NFs) that provide dispersion strengthening and radiation damage resistance for candidate Generation IV and future fusion reactor materials. This work is a small and focused part of a larger collaboration to produce large best practice NFA heats. The powders analyzed were rapidly solidified from a melt containing Fe-14%Cr, 3%W, 0.4%Ti and 0.2%Y by gas atomization in Ar, Ar/O, and He atmospheres. Note this represents a different processing path from conventional NFA production where metallic powders are mechanically alloyed with Y2O3 by ball milling. Electron probe microanalysis (EPMA), atom probe tomography (APT), transmission electron microscopy (TEM) and small angle neutron scattering (SANS) were used to characterize the powders in the as-atomized, ball milled and ball milled and annealed conditions. EPMA showed the Y is heterogeneously distributed and phase separated in all the as atomized powders, but attritor milling for 20 to 40 h is required to mix the Y. Milling also creates a significant quantity of O as well as N contamination. Subsequent powder annealing treatments, typically at 1150°C, result in the precipitation of a high density of NFs. All the annealed powder variants show a bimodal grain size distribution, but TEM and APT show NFs in both large and small grains. Reducing O content added during milling of the Ar atomized powders increased the precipitate size and decreased the number density, adversely affecting the hardness.

Microstructural Characterization of Rapidly Solidified Ultrahigh Strength Aluminum Alloys

1998 ◽  
Vol 4 (S2) ◽  
pp. 98-99
Author(s):  
D. H. Ping ◽  
K. Hono ◽  
A. Inoue
Keyword(s):  
Rapid Solidification ◽  
Microstructural Characterization ◽  
Atom Probe ◽  
Probe Field ◽  
Amorphous Phases ◽  
Ultrahigh Strength ◽  
Icosahedral Phases ◽  
Transmission Electron ◽  
Solidification Processes ◽  
Rapidly Solidified

Recently, Inoue et al. succeeded in fabricating ultrahigh-strength Al-based alloys consisting of a nanoscale mixture of α-Al and amorphous phases or a mixture of a-Al, amorphous and icosahedral phases in Al-TM-Ce, Al-TM-Ln (TM: transition metals) and Al-Cr-Co-Ce systems by rapid solidification [1-3]. In order to understand the mechanism of the nanoscale microstructural evolution during the rapid solidification processes in these nanocomposite alloys, we have characterized the microstructures of rapidly solidified Al94.5Cr3Co1.5Ce1 and Al96V4Fe2 alloys by atom probe field ion microscopy (APFIM) and high resolution transmission electron microscopy (HREM).TEM investigations have revealed that the as-quenched Al94.5Cr3Co1.5Ce1 alloy is composed of a nanoscale mixture of amorphous and α-Al. A typical TEM bright field micrograph is shown in Fig. 1. The microdiffraction patterns taken at various locations in the darkly contrasted region have shown that the region consists of a few interconnected α-Al grains and many localized amorphous regions which are trapped within the Al grains.

Precipitation Sequence and Kinetics in an Fe-Si-Ti Alloy

2011 ◽  
Vol 172-174 ◽  
pp. 833-838 ◽  
Author(s):  
Malika Perrier ◽  
Alexis Deschamps ◽  
Patricia Donnadieu ◽  
Frédéric de Geuser ◽  
Frédéric Danoix ◽  
...  
Keyword(s):  
Volume Fraction ◽  
High Volume ◽  
Tensile Tests ◽  
Atom Probe ◽  
Precipitate Size ◽  
Precipitation Sequence ◽  
Precipitation Kinetics ◽  
Temperature Range ◽  
Transmission Electron ◽  
Temporary Decrease

The Fe-Si-Ti system is known to show nanoscale precipitation of the Fe2SiTi Heusler phase with potentially high volume fraction (~4%), very high density and a size ranging from 1 to 20nm after artificial aging. The strong hardening potential of these precipitates make these steels candidates for automotive applications; however no understanding of the precipitation sequence (competition with other phases) nor the precipitation kinetics are available. The present study presents a quantitative study of the precipitation kinetics (size, volume fraction and number density) in a wide temperature range (450-800°C), realised by coupling systematically Small Angle Neutron Scattering (SANS), Transmission Electron microscopy (TEM) and Tomographic Atom Probe (TAP). Tensile tests were also carried out so as to determine the microstructure/properties relationships. Along the complete temperature range, it is shown that a compromise between time for precipitation and small precipitate sizes can be reached around 550°C. At this intermediate temperature, precipitation is shown to occur in two steps, linked with a second nucleation process after nucleation & growth of the first family of Fe2SiTi has been completed. This second precipitation step results in a temporary decrease in precipitate size and an increase in hardness. The nature of these precipitates is discussed in view of the TEM and TAP observations.

scholarly journals Effect of Tempering on the Bainitic Microstructure Evolution Correlated with the Hardness in a Low-Alloy Medium-Carbon Steel

2020 ◽  
Vol 51 (12) ◽  
pp. 6470-6481
Author(s):  
Adam Ståhlkrantz ◽  
Peter Hedström ◽  
Niklas Sarius ◽  
Hans-Åke Sundberg ◽  
Sören Kahl ◽  
...  
Keyword(s):  
Microstructural Characterization ◽  
Atom Probe ◽  
Medium Carbon Steel ◽  
Precipitate Size ◽  
X Ray Diffraction ◽  
Medium Carbon ◽  
Transmission Electron ◽  
Bainitic Microstructure ◽  
Effective Grain Size ◽  
Dislocation Annihilation

AbstractA low-alloy medium-carbon bainitic steel was isothermally tempered at 300 °C for up to 24 hours which led to a significant hardness decrease. In order to explain the decreasing hardness, extensive microstructural characterization using scanning and transmission electron microscopy, X-ray diffraction, and atom probe tomography was conducted. The experimental work was further supplemented by thermodynamic and kinetic simulations. It is found that the main underlying reason for the hardness reduction during tempering is related to dislocation annihilation, possibly also with corresponding changes in Cottrell atmospheres. On the other hand, cementite precipitate size, effective grain size of the bainite, and retained austenite fraction appear unchanged over the whole tempering cycle.

High-resolution x-ray imaging of small copper-rich precipitates in steels

1988 ◽  
Vol 46 ◽  
pp. 528-529
Author(s):  
J. R. Michael ◽  
K. A. Taylor
Keyword(s):  
Electron Microscopy ◽  
Thermomechanical Processing ◽  
Atom Probe ◽  
Ferrite Matrix ◽  
Scanning Transmission Electron Microscope ◽  
Probe Field ◽  
X Ray ◽  
Subsequent Transformation ◽  
Transmission Electron ◽  
Scanning Transmission

Although copper is considered an incidental or trace element in many commercial steels, some grades contain up to 1-2 wt.% Cu for precipitation strengthening. Previous electron microscopy and atom-probe/field-ion microscopy (AP/FIM) studies indicate that the precipitation of copper from ferrite proceeds with the formation of Cu-rich bcc zones and the subsequent transformation of these zones to fcc copper particles. However, the similarity between the atomic scattering amplitudes for iron and copper and the small misfit between between Cu-rich particles and the ferrite matrix preclude the detection of small (<5 nm) Cu-rich particles by conventional transmission electron microscopy; such particles have been imaged directly only by FIM. Here results are presented whereby the Cu Kα x-ray signal was used in a dedicated scanning transmission electron microscope (STEM) to image small Cu-rich particles in a steel. The capability to detect these small particles is expected to be helpful in understanding the behavior of copper in steels during thermomechanical processing and heat treatment.

Ordering in Ni4Mo by TEM and APFIM

1987 ◽  
Vol 45 ◽  
pp. 214-215
Author(s):  
E.A. Kenik ◽  
T.A. Zagula ◽  
M.K. Miller ◽  
J. Bentley
Keyword(s):  
Electron Irradiation ◽  
Low Temperatures ◽  
Short Range ◽  
Atom Probe ◽  
Range Order ◽  
Considerable Time ◽  
Probe Field ◽  
Disordered Phase ◽  
Transmission Electron ◽  
Diffraction Patterns

The state of long-range order (LRO) and short-range order (SRO) in Ni4Mo has been a topic of interest for a considerable time (see Brooks et al.). The SRO is often referred to as 1½0 order from the apparent position of the diffuse maxima in diffraction patterns, which differs from the positions of the LRO (D1a) structure. Various studies have shown that a fully disordered state cannot be retained by quenching, as the atomic arrangements responsible for the 1½0 maxima are present at temperatures above the critical ordering temperature for LRO. Over 20 studies have attempted to identify the atomic arrangements associated with this state of order. A variety of models have been proposed, but no consensus has been reached. It has also been shown that 1 MeV electron irradiation at low temperatures (∼100 K) can produce the disordered phase in Ni4Mo. Transmission electron microscopy (TEM), atom probe field ion microscopy (APFIM), and electron irradiation disordering have been applied in the current study to further the understanding of the ordering processes in Ni4Mo.

Devitrification products of rapidly solidified Ni-Nb amorphous alloys.

1990 ◽  
Vol 48 (4) ◽  
pp. 950-951
Author(s):  
G. A. Bertero ◽  
W.H. Hofmeister ◽  
N.D. Evans ◽  
J.E. Wittig ◽  
R.J. Bayuzick
Keyword(s):  
Electron Microscopy ◽  
Amorphous Structure ◽  
Sulphuric Acid Solution ◽  
X Ray Diffraction ◽  
High Fracture ◽  
Transmission Electron ◽  
Xrd Techniques ◽  
Rapidly Solidified ◽  
Electromagnetically Levitated

Rapid solidification of Ni-Nb alloys promotes the formation of amorphous structure. Preliminary results indicate promising elastic properties and high fracture strength for the metallic glass. Knowledge of the thermal stability of the amorphus alloy and the changes in properties with temperature is therefore of prime importance. In this work rapidly solidified Ni-Nb alloys were analyzed with transmission electron microscopy (TEM) during in-situ heating experiments and after isothermal annealing of bulk samples. Differential thermal analysis (DTA), scanning electron microscopy (SEM) and x-ray diffraction (XRD) techniques were also used to characterize both the solidification and devitrification sequences.Samples of Ni-44 at.% Nb were electromagnetically levitated, melted, and rapidly solidified by splatquenching between two copper chill plates. The resulting samples were 100 to 200 μm thick discs of 2 to 3 cm diameter. TEM specimens were either ion-milled or alternatively electropolished in a methanol-10% sulphuric acid solution at 20 V and −40°C.

Transmission Electron Microscopic Observations of Al3Li and Al3Ti Precipitation in A Rapidly Solidified Al-3Li-0.2Ti ALLOY

1980 ◽  
Vol 38 ◽  
pp. 336-337
Author(s):  
J. E. O’Neal ◽  
K. K. Sankaran ◽  
S. M. L. Sastry
Keyword(s):  
Rapid Solidification ◽  
Metallic Substrate ◽  
Deformation Characteristics ◽  
Phase Decomposition ◽  
Electron Microscopic ◽  
Transmission Electron ◽  
Supersaturated Solid Solutions ◽  
Transmission Electron Microscopic ◽  
Rapidly Solidified ◽  
Microstructural Homogeneity

Rapid solidification of a molten, multicomponent alloy against a metallic substrate promotes greater microstructural homogeneity and greater solid solubility of alloying elements than can be achieved by slower-cooling casting methods. The supersaturated solid solutions produced by rapid solidification can be subsequently annealed to precipitate, by controlled phase decomposition, uniform 10-100 nm precipitates or dispersoids. TEM studies were made of the precipitation of metastable Al3Li(δ’) and equilibrium AL3H phases and the deformation characteristics of a rapidly solidified Al-3Li-0.2Ti alloy.

scholarly journals Revisiting the Bøggild Intergrowth in Iridescent Labradorite Feldspars: Ordering, Kinetics, and Phase Equilibria

Minerals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 727
Author(s):  
Shiyun Jin ◽  
Huifang Xu ◽  
Seungyeol Lee
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Atom Probe ◽  
Phase Region ◽  
Two Phase ◽  
Subsolidus Phase ◽  
Plagioclase Feldspar ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Transmission

The enigmatic Bøggild intergrowth in iridescent labradorite crystals was revisited in light of recent work on the incommensurately modulated structures in the intermediated plagioclase. Five igneous samples and one metamorphic labradorite sample with various compositions and lamellar thicknesses were studied in this paper. The lamellar textures were characterized with conventional transmission electron microscopy (TEM) and scanning transmission electron microscopy (STEM). The compositions of individual lamellae were analyzed with high-resolution energy-dispersive X-ray spectroscopy (EDS) mapping and atom probe tomography (APT). The average structure states of the studied samples were also compared with single-crystal X-ray diffraction data (SC-XRD). The Na-rich lamellae have a composition of An44–48, and the Ca-rich lamellae range from An56 to An63. Significant differences between the lamellar compositions of different samples were observed. The compositions of the Bøggild intergrowth do not only depend on the bulk compositions, but also on the thermal history of the host rock. The implications on the subsolidus phase relationships of the plagioclase feldspar solid solution are discussed. The results cannot be explained by a regular symmetrical solvus such as the Bøggild gap, but they support an inclined two-phase region that closes at low temperature.

Sign in / Sign up

Export Citation Format

Share Document