Effect of Sodium Silicate Properties in Alkali-Activation of Mexican Blast Furnace Slag

2016 ◽  
Vol 1813 ◽  
Author(s):  
O. F. Cortés-Salmerón ◽  
M. L. García-Chávez ◽  
T. A. García-Mejía
Keyword(s):  
Blast Furnace ◽  
Sodium Silicate ◽  
Blast Furnace Slag ◽  
Alkali Activation ◽  
X Ray Diffraction ◽  
Weight Percentage ◽  
Average Value ◽  
Accelerated Curing ◽  
Compressive Strength Test ◽  
Furnace Slag

ABSTRACTThe present work is a study on alkali activation of Mexican blast furnace slag, using sodium silicate. The aim is to produce an optimal specimen, homogeneous without carbonation, and with small fraction of crystalline phases, similar to CSH, which provide mechanical properties suitable to use in the construction industry. The samples were prepared using sodium silicate activator solutions with modulus (SiO2/Na2O) of 1.25, 1.5, and 1.75. The weight percentage of Na2O in the activator solutions was added at 4, 6 and 8% relative to the slag weight. The prepared samples were stored in sealed molds, at room temperature (20°C), during 7 days. The X-ray diffraction has revealed the presence of an amorphous phase, semi crystalline clinotobermorite phase and signals of calcium carbonate for the samples of 4 and 6 % of Na2O; in contrast with the 8% Na2O, where the latter signals almost disappeared. The specimen selected as optimal was prepared with an activator concentration of 8% of Na2O /Slag, and SiO2/Na2O of 1.25. A specimen under these optimal conditions was prepared with accelerated curing (40°C, humidity, 48 hours), and a compressive strength test was attained, with an average value of 52 MPa at 3 days.

scholarly journals Autogenous Deformation of Alkali-Activated Blast Furnace Slag Concrete Subjected to Variable Curing Temperatures

2019 ◽  
Vol 2019 ◽  
pp. 1-8 ◽  
Author(s):  
Katalin Orosz ◽  
Abeer Humad ◽  
Hans Hedlund ◽  
Andrzej Cwirzen
Keyword(s):  
Blast Furnace ◽  
Diffraction Analysis ◽  
Sodium Silicate ◽  
Blast Furnace Slag ◽  
Curing Temperature ◽  
X Ray Diffraction ◽  
X Ray ◽  
Activated Slag ◽  
Furnace Slag ◽  
Alkali Activated

Deformations of alkali-activated slag concrete (AASC) with high MgO and Al2O3 content, subjected to variable curing temperature were studied. Sodium silicate and sodium carbonate were used as alkali activators. The obtained results showed development of deformations consisting of both shrinkage and expansion. Shrinkage appeared not to be affected by the activator type, while the expansion developed after the cooling down phase in stabilized isothermal conditions and did not stop within the duration of the tests. X-ray diffraction analysis performed shortly after the cooling down phase indicated the formation of crystalline hydrotalcite, which was associated with the observed expansion. A mixture with a higher amount of sodium silicate showed less expansion, likely due to the accelerated hydration and geopolymerization leading to the increased stiffness of the binder matrix.

scholarly journals The Effects of Temperature on the Hydrothermal Synthesis of Hydroxyapatite-Zeolite Using Blast Furnace Slag

Materials ◽  
2019 ◽  
Vol 12 (13) ◽  
pp. 2131 ◽  
Author(s):  
G.U. Ryu ◽  
G.M. Kim ◽  
Hammad R. Khalid ◽  
H.K. Lee
Keyword(s):  
Blast Furnace ◽  
Hydrothermal Synthesis ◽  
Blast Furnace Slag ◽  
Raw Material ◽  
X Ray Diffraction ◽  
X Ray ◽  
Different Temperatures ◽  
Type Zeolite ◽  
Effects Of Temperature ◽  
Furnace Slag

Blast furnace slag, an industrial by-product, is emerging as a potential raw material to synthesize hydroxyapatite and zeolite. In this study, the effects of temperature on the hydrothermal synthesis of hydroxyapatite-zeolite from blast furnace slag were investigated. Specimens were synthesized at different temperatures (room temperature, 50, 90, 120, or 150 °C). The synthesized specimens were analyzed qualitatively and quantitatively via X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), BET/BJH, and scanning electron microscopy/energy dispersive using X-ray analysis (SEM/EDX). It was found that the hydroxyapatite phase was synthesized at all the reaction temperatures, while faujasite type zeolite appeared in the specimens synthesized at 90 and 120 °C. Moreover, faujasite was replaced by hydroxysodalite in the specimens synthesized at 150 °C. Additionally, the crystals of the hydroxyapatite tended to become larger and total crystallinity increased as the reaction temperature increased.

scholarly journals Geopolymer Based on Mechanically Activated Air-cooled Blast Furnace Slag

Materials ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1134 ◽  
Author(s):  
Ilda Tole ◽  
Magdalena Rajczakowska ◽  
Abeer Humad ◽  
Ankit Kothari ◽  
Andrzej Cwirzen
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Portland Cement ◽  
Sodium Silicate ◽  
Blast Furnace Slag ◽  
Ball Mill ◽  
Efficient Solution ◽  
Building Materials ◽  
Furnace Slag ◽  
Alkali Activated

An efficient solution to increase the sustainability of building materials is to replace Portland cement with alkali-activated materials (AAM). Precursors for those systems are often based on water-cooled ground granulated blast furnace slags (GGBFS). Quenching of blast furnace slag can be done also by air but in that case, the final product is crystalline and with a very low reactivity. The present study aimed to evaluate the cementitious properties of a mechanically activated (MCA) air-cooled blast furnace slag (ACBFS) used as a precursor in sodium silicate alkali-activated systems. The unreactive ACBFS was processed in a planetary ball mill and its cementing performances were compared with an alkali-activated water-cooled GGBFS. Mixes based on mechanically activated ACBFS reached the 7-days compressive strength of 35 MPa and the 28-days compressive strength 45 MPa. The GGBFS-based samples showed generally higher compressive strength values.

scholarly journals Utilization of Calcium Carbide Residue Using Granulated Blast Furnace Slag

Materials ◽  
2019 ◽  
Vol 12 (21) ◽  
pp. 3511 ◽  
Author(s):  
Joonho Seo ◽  
Solmoi Park ◽  
Hyun No Yoon ◽  
Jeong Gook Jang ◽  
Seon Hyeok Kim ◽  
...  
Keyword(s):  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Calcium Carbide ◽  
Magic Angle Spinning ◽  
Magic Angle ◽  
X Ray Diffraction ◽  
Granulated Blast Furnace Slag ◽  
Calcium Carbide Residue ◽  
Angle Spinning ◽  
Furnace Slag

The solidification and stabilization of calcium carbide residue (CCR) using granulated blast furnace slag was investigated in this study. CCR binding in hydrated slag was explored by X-ray diffraction, 29Si and 27Al magic angle spinning (MAS) nuclear magnetic resonance (NMR) spectroscopy, and thermodynamic calculations. Mercury intrusion porosimetry and and compressive strength tests assessed the microstructure and mechanical properties of the mixtures of slag and CCR. C-A-S-H gel, ettringite, hemicarbonate, and hydrotalcite were identified as the main phases in the mixture of slag and CCR. The maximum CCR uptake by slag and the highest volume of precipitated solid phases were reached when CCR loading in slag is 7.5% by mass of slag, according to the thermodynamic prediction. This feature is also experimentally observed in the microstructure, which showed an increase in the pore volume at higher CCR loading.

Comparison of Selected Properties of Portland Cement Based Materials and Alkali Activated Materials Based on Granulated Blast Furnace Slag

2016 ◽  
Vol 865 ◽  
pp. 107-113 ◽  
Author(s):  
Pavel Mec ◽  
Jana Boháčová ◽  
Josef Koňařík
Keyword(s):  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Water Glass ◽  
Sodium Metasilicate ◽  
Alkali Activation ◽  
Granulated Blast Furnace Slag ◽  
Cement Based Materials ◽  
One Year ◽  
Furnace Slag ◽  
Alkali Activated

Alkali activated systems are materials formed by alkali-activation of latent hydraulic or pozzolanic materials. The outcome is a polymeric structure with properties comparable to materials based on cement.The principle of the experiment is to compare selected properties of alkali-activated materials based on blast furnace slag and using various types of activator (sodium water glass, potassium water glass, DESIL AL and sodium metasilicate) to binders based on white and Portland cements of the highest quality. The samples were left for one year in environments simulating the conditions in the interior and exterior. Selected physical-mechanical properties were evaluated and compared.

Crystallization Behavior and Growing Process of Rutile Crystals in Ti-Bearing Blast Furnace Slag

2016 ◽  
Vol 35 (8) ◽  
pp. 787-797
Author(s):  
Wu Zhang ◽  
Li Zhang ◽  
Yuhai Li ◽  
Xin Li
Keyword(s):  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Crystallization Process ◽  
Elevated Temperatures ◽  
Avrami Equation ◽  
X Ray Diffraction ◽  
Experimental Parameters ◽  
Kinetics Of ◽  
Crystal Seed ◽  
Furnace Slag

AbstractThe aim of the present work is to elucidate crystallization and growing process of rutile crystals in Ti-bearing blast furnace slag. The samples were taken from the liquid slag and quenched at once at elevated temperatures in order to analyze phase transaction of titanium and grain size of rutile crystals. Crystallization and growing kinetics of rutile crystals under elevated temperature conditions were calculated, and the crystallization process of rutile crystals under isothermal conditions was expressed by Avrami equation. The effects of experimental parameters, such as experimental temperatures, SiO2 addition, cooling rate, crystal seed addition and oxygen flow, were investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM), the optimal conditions for rutile crystals to grow up were obtained. Distribution and movement state of rutile crystals in the slag were analyzed.

SODIUM SILICATE ACTIVATED SLAG-FLY ASH CEMENT

2014 ◽  
Vol 1 (1) ◽  
Author(s):  
Jan Pieter Vermeulen ◽  
Natalie Lloyd
Keyword(s):  
Blast Furnace ◽  
Fly Ash ◽  
Silica Fume ◽  
Sodium Silicate ◽  
Blast Furnace Slag ◽  
High Strength ◽  
Chemical Balance ◽  
Aluminum Hydrate ◽  
Activated Slag ◽  
Furnace Slag

This research examines an alternative binder, Alkali Activated Cement (AAC), examining the fresh and hardened mechanical properties of twelve AAC mortar mixes with varying mixture proportions of blast-furnace slag, fly ash, sodium silicate (the alkali activator), and additional water. In addition to the Slag-Fly Ash mortars, nine mixtures with blast-furnace slag, silica fume, aluminum hydrate, sodium silicate, and water were tested. For all mortars, the compressive strength was exponentially related to the water/activator-solids ratio. Mortar strengths at 28 days ranged from 5 MPa to 20 MPa. Increasing the slag to binder-solids ratio from 0.1 to 0.2 increased the strength with water to binder ratios from 0.2 to 0.4. However, rapid or almost instantaneous setting times were observed for a slag to binder-solids ratio of 0.2. The research concluded that using a carefully chosen mix design can prevent quick setting while still achieving high strength and acceptable workability. It is suggested the CaO to binder-solids ratio remain below 0.07; a sodium silicate to binder solids ratio of around 0.25 is optimal; a water to binder-solids ratio should be around 0.3. When replacing fly ash, a Si/Al ratio above 2 is recommended. This research concluded that other solids (Silica Fume and Aluminum Hydrate) could replace Slag and/or Fly Ash if the overall chemical balance of the system is maintained.

Sign in / Sign up

Export Citation Format

Share Document