The Sputter Deposition of Metal Multilayers

1987 ◽  
Vol 103 ◽  
Author(s):  
R. E. Somekh ◽  
R. J. Highmore ◽  
K. Page ◽  
R. J. Home ◽  
Z. H. Barber
Keyword(s):  
Differential Scanning Calorimetry ◽  
Sputter Deposition ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Monotonic Increase ◽  
Preliminary Work ◽  
Sputtering Pressure

ABSTRACTWe describe the strategy that we are using to make precision metal multilayers. Differential scanning calorimetry has been used with the Ni/Zr system to study the abruptness of the interface as a function of the sputtering pressure. For 10nm period multilayers there is a monotonic increase in the width of the interface with increasing sputtering pressure. W/Si multilayers have been studied as a function of both the sputtering pressure and the relative thicknesses of tungsten and silicon. At reasonably low sputtering pressures a well textured (110) tungsten X-ray peak is seen which is compatible with the expected thickness of the tungsten layers.Finally, we report some preliminary work on sputtering from tungsten and silicon targets which are at different distances from the substrate so that the degrees of bombardment on the growing layers of the film can be independently varied.

Kinetics and Thermodynamics of the Formation of Thin Film Titanium Diselicide

1995 ◽  
Vol 398 ◽  
Author(s):  
R.J. Kasica ◽  
E.J. Cotts ◽  
R.G. Ahrens
Keyword(s):  
Thin Film ◽  
Differential Scanning Calorimetry ◽  
Solid State ◽  
Isothermal Calorimetry ◽  
Sputter Deposition ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Average Composition ◽  
Kinetics And Thermodynamics ◽  
X Ray

ABSTRACTMultilayered difiiision couples consisting of alternating layers of titanium (Ti) and amorphous silicon (a-Si) have been fabricated using sputter deposition with a range of modulation lengths corresponding to an average composition of Ti33 Si67. We have used differential scanning calorimetry to measure the enthalpy evolved during the solid state reaction a-Si + Ti → C49-TiSi2 and have characterized the phases formed using x-ray diffraction analysis. An average measured enthalpy of formation, ΔΗ was found to be ΔΗ = -58 + 9 kJ/g atom for thin film samples. Using scanning and isothermal calorimetry measurements, we have also characterized the kinetics involved during the initial intermixing stage.

A Study of the Interactions Between Oligoamidephosphate (OAPh) and Curatives in a Sulphenamide-Accelerated Sulphur Vulcanizing System

1999 ◽  
Vol 19 (2) ◽  
pp. 95-108 ◽  
Author(s):  
Todorka G. Vladkova ◽  
Alexander Chr. Alaminov ◽  
Milka G. Pankova
Keyword(s):  
Differential Scanning Calorimetry ◽  
Zinc Oxide ◽  
Ir Spectroscopy ◽  
Room Temperature ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Sulphur Vulcanization

Abstract The possible interactions between oligoamidephosphate (OAPli) and the curatives of a sulphenamide-accelerated sulphur vulcanizing system were studied by differential scanning calorimetry, IR-spectroscopy, and X-ray analysis. The interactions in double mixtures were between OAPh and zinc oxide (ZnO) and OAPh and sulphur. The OAPh/ZnO interaction that starts at room temperature seems to be the key for understanding the peculiarities of sulphenamide-accelerated sulphur vulcanization in the presence of OAPh.

Research on compatibility and surface of high impact bio-based polyamide

2021 ◽  
pp. 095400832110055
Author(s):  
Yang Wang ◽  
Yuhui Zhang ◽  
Yuhan Xu ◽  
Xiucai Liu ◽  
Weihong Guo
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Differential Scanning Calorimetry ◽  
Crystallization Behavior ◽  
High Impact ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Scanning Electron

The super-tough bio-based nylon was prepared by melt extrusion. In order to improve the compatibility between bio-based nylon and elastomer, the elastomer POE was grafted with maleic anhydride. Scanning Electron Microscopy (SEM) and Thermogravimetric Analysis (TGA) were used to study the compatibility and micro-distribution between super-tough bio-based nylon and toughened elastomers. The results of mechanical strength experiments show that the 20% content of POE-g-MAH has the best toughening effect. After toughening, the toughness of the super-tough nylon was significantly improved. The notched impact strength was 88 kJ/m2 increasing by 1700%, which was in line with the industrial super-tough nylon. X-ray Diffraction (XRD) and Differential Scanning Calorimetry (DSC) were used to study the crystallization behavior of bio-based PA56, and the effect of bio-based PA56 with high crystallinity on mechanical properties was analyzed from the microstructure.

scholarly journals Synthesis and mesomorphic properties of calamitic malonates and cyanoacetates tethered to 4-cyanobiphenyls

2012 ◽  
Vol 8 ◽  
pp. 371-378 ◽  
Author(s):  
Katharina C Kress ◽  
Martin Kaller ◽  
Kirill V Axenov ◽  
Stefan Tussetschläger ◽  
Sabine Laschat
Keyword(s):  
Differential Scanning Calorimetry ◽  
Ambient Temperature ◽  
Liquid Crystalline ◽  
X Ray Diffraction ◽  
Cyanoacetic Acid ◽  
Scanning Calorimetry ◽  
Isotropic Liquid ◽  
X Ray ◽  
Nematic Phases ◽  
Mesomorphic Properties

4-Cyano-1,1'-biphenyl derivatives bearing ω-hydroxyalkyl substituents were reacted with methyl 3-chloro-3-oxopropionate or cyanoacetic acid, giving liquid-crystalline linear malonates and cyanoacetates. These compounds formed monotropic nematic phases at 62 °C down to ambient temperature upon cooling from the isotropic liquid. The mesomorphic properties were investigated by differential scanning calorimetry, polarizing optical microscopy and X-ray diffraction (WAXS).

Inosose-Flüssigkristalle / Inosose Liquid Crystals

1990 ◽  
Vol 45 (7) ◽  
pp. 1084-1090 ◽  
Author(s):  
Klaus Praefcke ◽  
Bernd Kohne ◽  
Andreas Eckert ◽  
Joachim Hempel
Keyword(s):  
Differential Scanning Calorimetry ◽  
Liquid Crystal ◽  
High Temperature ◽  
Liquid Crystalline ◽  
Structural Features ◽  
Lyotropic Liquid Crystal ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Alkyl Chains

Six S,S-dialkyl acetals 2a-f of inosose (1), tripodal in structure, have been synthesized, characterized and investigated by optical microscopy and differential scanning calorimetry (d.s.c.). The four S,S-acetals 2c-f with sufficiently long alkyl chains are thermotropic liquid crystalline; 2 e and 2 f are even dithermomesomorphic. Each of these four inosose derivatives 2c-f exhibits monotropically a most likely cubic mesophase (MI); in addition 2e and 2f show enantiotropically a hexagonal mesophase (Hx) with a non-covalent, supramolecular H-bridge architecture. Whereas the nature of the optically isotropic mesophase MI needs further clarification the stable high temperature mesophase Hx of 2 e and 2 f has been established by a miscibility test using a sugar S,S-dialkyl acetal also tripodal in structure and with a Hx phase proved by X-ray diffraction, but in contrast to 2 with an acyclic hydrophilic part. Similarities of structural features between the Hx-phases of 2e and 2f as well as of other thermotropic and lyotropic liquid crystal systems are discussed briefly.

scholarly journals Formation of Pharmaceutical Salts and Cocrystals via Vapour-Assisted Tumbling (VAT) – A Solvent Efficient Process with Potential Industrial Applications

2021 ◽  
Author(s):  
Alexander J. Stirk ◽  
Fabio E. S. Souza ◽  
Jenny Gerster ◽  
Fatemeh M. Mir ◽  
Avedis Karadeolian ◽  
...  
Keyword(s):  
Differential Scanning Calorimetry ◽  
Environmental Impact ◽  
Industrial Applications ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
New Techniques ◽  
X Ray ◽  
Industry Standard ◽  
Pharmaceutical Salts ◽  
Solid Form

Crystallisations on both the academic and industrial scale often use large volumes of solvent. In order decrease the environmental impact of such processes, new techniques must be discovered that increase the efficiency of the solvents used. Introduced here is a process that combines repurposed industry standard hardware and aspects of mechanochemistry to produce a technique we call “Vapour Assisted Tumbling” (VAT). Pharmaceutical and well-known cocrystals and salts were formed by tumbling the coformers in an atmosphere of vaporised solvent, in this study, methanol (MeOH). This was done inside a custom built analogue of an industrial rotary cone dryer (RCD). It was found that a desired solid form could be obtained as monitored by powder X-ray diffraction and differential scanning calorimetry. By repurposing industrial RCDs, it is feasible that solid forms can be crystallised with both minimal and reusable/recyclable solvent – drastically lowering the environmental impact of such transformations.

Sign in / Sign up

Export Citation Format

Share Document