Sound Absorption Characteristics of Porous Steel Manufactured by Lost Carbonate Sintering

2009 ◽  
Vol 1188 ◽  
Author(s):  
Miao Lu ◽  
Carl Hopkins ◽  
Yuyuan Zhao ◽  
Gary Seiffert
Keyword(s):  
Absorption Coefficient ◽  
Pore Size ◽  
Sound Absorption ◽  
Single Layer ◽  
Normal Incidence ◽  
Sound Absorption Coefficient ◽  
Absorption Coefficients ◽  
Impedance Tube ◽  
Absorption Characteristics

AbstractThis paper investigates the sound absorption characteristics of porous steel samples manufactured by Lost Carbonate Sintering. Measurements of the normal incidence sound absorption coefficient were made using an impedance tube for single-layer porous steel discs and assemblies comprising four layers of porous steel discs. The sound absorption coefficient was found not to vary significantly with pore size in the range of 250-1500 μm. In general, the absorption coefficient increases with increasing frequency and increasing thickness, and peaks at specific frequencies depending on the porosity. An increase in porosity tends to increase the frequency at which the sound absorption coefficient reaches this peak. An advantage was found in using an assembly of samples with gradient porosities of 75%-70%-65%-60% as it gave higher and more uniform sound absorption coefficients than an assembly with porosities of 75%.

scholarly journals Extrusion Foaming of Lightweight Polystyrene Composite Foams with Controllable Cellular Structure for Sound Absorption Application

Polymers ◽  
2019 ◽  
Vol 11 (1) ◽  
pp. 106 ◽  
Author(s):  
Yanpei Fei ◽  
Wei Fang ◽  
Mingqiang Zhong ◽  
Jiangming Jin ◽  
Ping Fan ◽  
...  
Keyword(s):  
Absorption Coefficient ◽  
Cellular Structure ◽  
Sound Absorption ◽  
Lignin Content ◽  
Normal Incidence ◽  
Sound Absorption Coefficient ◽  
Multiwall Carbon Nanotube ◽  
Nucleation Effect ◽  
Composite Foams ◽  
Extrusion Foaming

Polymer foams are promising for sound absorption applications. In order to process an industrial product, a series of polystyrene (PS) composite foams were prepared by continuous extrusion foaming assisted by supercritical CO2. Because the cell size and cell density were the key to determine the sound absorption coefficient at normal incidence, the bio-resource lignin was employed for the first time to control the cellular structure on basis of hetero-nucleation effect. The sound absorption range of the PS/lignin composite foams was corresponding to the cellular structure and lignin content. As a result, the maximum sound absorption coefficient at normal incidence was higher than 0.90. For a comparison, multiwall carbon nanotube (MWCNT) and micro graphite (mGr) particles were also used as the nucleation agent during the foaming process, respectively, which were more effective on the hetero-nucleation effect. The mechanical property and thermal stability of various foams were measured as well. Lignin showed a fire retardant effect in PS composite foam.

scholarly journals Elucidating the Sound Absorption Characteristics of Foxtail Millet (Setariaitalica) Husk

Materials ◽  
2020 ◽  
Vol 13 (22) ◽  
pp. 5126
Author(s):  
Dhayalini Balasubramanian ◽  
Senthil Rajendran ◽  
Bhuvanesh Srinivasan ◽  
Nirmalakumari Angamuthu
Keyword(s):  
Absorption Coefficient ◽  
Sound Absorption ◽  
Foxtail Millet ◽  
Air Gap ◽  
Composite Panel ◽  
Sound Absorption Coefficient ◽  
Mass Content ◽  
Frequency Range ◽  
Backing Material ◽  
Absorption Characteristics

The current study deals with the analysis of sound absorption characteristics of foxtail millet husk powder. Noise is one the most persistent pollutants which has to be dealt seriously. Foxtail millet is a small seeded cereal cultivated across the world and its husk is less explored for its utilization in polymer composites. The husk is the outer protective covering of the seed, rich in silica and lingo-cellulose content making it suitable for sound insulation. The acoustic characterization is done for treated foxtail millet husk powder and polypropylene composite panels. The physical parameters like fiber mass content, density, and thickness of the composite panel were varied and their influence over sound absorption was mapped. The influence of porosity, airflow resistance, and tortuosity was also studied. The experimental result shows that 30-mm thick foxtail millet husk powder composite panel with 40% fiber mass content, 320 kg/m3 density showed promising sound absorption for sound frequency range above 1000 Hz. We achieved noise reduction coefficient (NRC) value of 0.54. In view to improve the performance of the panel in low-frequency range, we studied the efficiency of incorporating air gap and rigid backing material to the designed panel. We used foxtail millet husk powder panel of density 850 kg/m3 as rigid backing material with varying air gap thickness. Thus the composite of 320 kg/m3 density, 30-mm thick when provided with 35-mm air gap and backing material improved the composite’s performance in sound frequency range 250 Hz to 1000 Hz. The overall sound absorption performance was improved and the NRC value and average sound absorption coefficient (SAC) were increased to 0.7 and 0.63 respectively comparable with the commercial acoustic panels made out of the synthetic fibers. We have calculated the sound absorption coefficient values using Delany and Bezlay model (D&B model) and Johnson–Champoux–Allard model (JCA model) and compared them with the measured sound absorption values.

Sound Absorption Behavior of Porous Al Produced by Spacer Method

2006 ◽  
Vol 15-17 ◽  
pp. 422-427
Author(s):  
Tetsumune Kuromura ◽  
Masataka Hakamada ◽  
Y. Chen ◽  
Hiromu Kusuda ◽  
Mamoru Mabuchi
Keyword(s):  
Absorption Coefficient ◽  
Pore Size ◽  
Sound Absorption ◽  
Size Range ◽  
Absorption Capacity ◽  
The Other ◽  
Sound Absorption Coefficient ◽  
Specimen Thickness ◽  
Pore Sizes ◽  
Other Hand

Porous Al specimens with a pore size range from 212-300 to 610-700 μm, a porosity from 85 to 95% and a specimen thickness from 2 to 20 mm were produced by the spacer method, and their sound absorption capacity was investigated. For these specimens, sound absorption coefficient increased with increasing porosity. On the other hand, sound absorption coefficient varied inconsistently with the variation of pore sizes. The latter may be attributed to variation of aperture sizes of each specimen because the porous Al specimens with differerent pore sizes produced by the spacer method should have different aperture sizes. Sound absorption coefficient increased at the frequency below 2000 Hz with increasing specimen thickness.

scholarly journals Sound Absorption Coefficient of Different Green Materials Polymer on Noise Reduction

2020 ◽  
Vol 9 (3) ◽  
pp. 2773-2777
Keyword(s):  
Absorption Coefficient ◽  
Noise Reduction ◽  
Sound Absorption ◽  
New Technologies ◽  
Raw Materials ◽  
Agricultural Waste ◽  
Noise Pollution ◽  
Sound Absorption Coefficient ◽  
Absorption Coefficients ◽  
Green Materials

One of the sources of noise pollution to environment is from the consumption of electrical and mechanical appliances usage at home and industries. Growth development and advancement of heavy equipment in construction work further emphasize the necessity used of new technologies for noise reduction. The best technique of control or reducing of noise is by using the materials that can absorb the noise by materials itself. Potential materials from agricultural waste as sound absorber were identified. There are two main objectives in this study; First is to produce acoustic absorber by using natural materials. Second is to identify their sound absorption coefficients. The samples were fabricated using the raw materials from banana stem, grass, palm oil leaves and lemongrass mixed with binding agents of polyurethane and hardener to the ratio of 1:4. The diameters of the samples consist of 28mm and 100mm and the thickness is 10mm. The samples sound absorption coefficients were measured according to standards ASTM E1050-98 / ISO 105342-2 (Impedance tube method). Sound absorption coefficient of the materials depends on frequencies choose. The frequencies values used in this study were in the range from 500Hz to 4500Hz. Material made from grass have a higher average sound absorption coefficient value which is 0.553. All tested samples also can be categories under class D type of materials based on sound absorption coefficient value.

Sound absorption of textile curtains – theoretical models and validations by experiments and simulations

2016 ◽  
Vol 88 (1) ◽  
pp. 36-48 ◽  
Author(s):  
Reto Pieren ◽  
Beat Schäffer ◽  
Stefan Schoenwald ◽  
Kurt Eggenschwiler
Keyword(s):  
Absorption Coefficient ◽  
Sound Absorption ◽  
Planning Process ◽  
Measurement Data ◽  
Theoretical Models ◽  
Sound Absorption Coefficient ◽  
Absorption Coefficients ◽  
Semi Empirical ◽  
Field Sound ◽  
Good Agreement

Textile curtains can be designed to be good sound absorbers. Their acoustical performance, as usually described by the sound absorption coefficient, not only depends on the textile itself but also on the drapery fullness and the backing condition, that is, the spacing between the fabric and a rigid backing wall, or the absence of a backing in the case of a freely hanging curtain. This article reviews existing models to predict the diffuse-field sound absorption coefficient, which to date can only predict the case of flat curtains. A set of existing models is extended to the case of curtains with drapery fullness using a semi-empirical approach. The models consider different backing conditions, including freely hanging curtains. The existing and new models are validated by comparing predicted sound absorption coefficients with data measured in a reverberation room. Hereby, curtains consisting of different fabrics and with different degrees of fullness are considered. Besides situations with rigid backing, also the measurement data of textiles hung freely in space are included in this study. Comparisons reveal a very good agreement between measured and predicted sound absorption coefficients. Compared to currently available commercial sound absorption prediction software that can only handle the situation of flat textiles with rigid backing, the results of the presented models not only show a better agreement with measured data, but also cover a broader range of situations. The presented models are thus well applicable in the design and development of new textiles as well as in the room acoustical planning process.

COMPARISON OF NORMAL INCIDENT SOUND ABSORPTION COEFFICIENT OF DIRECT PIERCING CARVED WOOD PANEL FOR CIRCULAR, GEOMETRY AND FLORAL DESIGN

2016 ◽  
Vol 78 (6-10) ◽  
Author(s):  
Mohd Zamri Jusoh ◽  
Nazli Che Din ◽  
Mohamad Ngasri Dimon
Keyword(s):  
Boundary Element Method ◽  
Absorption Coefficient ◽  
Sound Absorption ◽  
Sound Intensity ◽  
Normal Incidence ◽  
Sound Absorption Coefficient ◽  
Wood Panel ◽  
High Frequencies ◽  
Wood Carving ◽  
Circular Design

Direct Piercing Carved Wood Panel (DPCWP) is among the famous Malay wood carving art in the Malay culture. It is the best example of Malay people’s creativity and masterpiece. In this paper, the comparison of normal incidence sound absorption coefficient,  (SAC) for three major types of design for the DPCWP is discussed. The simplest form of DPCWP, the circular type, then the geometry and floral types were investigated based on simulation and measurement works using sound intensity method to determine the normal incidence SAC, for 30% and 40% perforation ratios. The simulation work was carried out by using BEASY Acoustic software based on Boundary Element Method (BEM). From the results, there is an identical trend for DPCWP with geometry and floral design from 250 Hz to 4 kHz. At high frequencies (1 kHz to 4 kHz), both design show the tendency of decrement, suggesting that the complexity of the design does affect the average SAC value. However, for circular design, SAC is higher than other design at 1 kHz and shows a similar trend with other design at 2 kHz and 4 kHz for both simulation and measurement result.

Sign in / Sign up

Export Citation Format

Share Document