Epitaxial Growth of Silicon on CoSi2 (001)/Si (001)

1991 ◽  
Vol 220 ◽  
Author(s):  
Q. F. Xiao ◽  
J. R. Jimenez ◽  
L. J. Schowalter ◽  
L. Luo ◽  
T. E. Mitchell ◽  
...  
Keyword(s):  
Growth Conditions ◽  
High Energy ◽  
Thin Layers ◽  
Ex Situ ◽  
High Crystalline Quality ◽  
Cross Sectional ◽  
Ion Channeling ◽  
Transmission Electron ◽  
Reconstructed Surface

ABSTRACTEpitaxial Si layers have been grown under a variety of growth conditions on CoSi2 (001) by molecular beam epitaxy (MBE). The structural properties of the Si overgrowth were studied by in-situ Reflection High Energy Electron Diffraction (RHEED), as well as ex-situ MeV4He+ ion channeling and High Resolution Transmission Electron Microscopy (HRTEM). Strong influences of the CoSi2 surface reconstruction on the Si overgrowth have been observed. RHEED studies show islanding growth of Si on the CoSi2 (001) (3/√2 × √2)R45 reconstructed surface, but smooth growth of Si on the CoSi2 (001) {√2 × √2)R45 reconstructed surface, under the same growth conditions. The growth of Si on thin layers of CoSi2 (2nm-6nm) with (√2 × √2)R45 reconstructed surface at 460°C results in high crystalline quality for the Si top layer, as indicated by good channeling minimum yield (Xmin < 6%), but cross-sectional TEM shows that the CoSi2 layers are discontinuous. We also report preliminary results on Si grown on a 2 × 2 reconstructed CoSi2 (001) surface.

In Situ Analysis of magnetic and Structural Properties of Epitaxial and Polycrystalline Ni80Fe20 Thin Films

1993 ◽  
Vol 313 ◽  
Author(s):  
I. Hashim ◽  
H.A. Atwater ◽  
Thomas J. Watson
Keyword(s):  
Magnetic Properties ◽  
Kerr Effect ◽  
High Energy ◽  
Epitaxial Films ◽  
Interface Roughness ◽  
Ex Situ ◽  
X Ray Diffraction ◽  
Cross Sectional ◽  
Transmission Electron

ABSTRACTWe have investigated structural and magnetic properties of epitaxial Ni80Fe20 films grown on relaxed epitaxial Cu/Si (001) films. The crystallographic texture of these films was analyzed in situ by reflection high energy electron diffraction (RHEED), and ex situ by x-ray diffraction and cross-sectional transmission electron Microscopy (XTEM). In particular, RHEED intensities were recorded during epitaxial growth, and intensity profiles across Bragg rods were used to calculate the surface lattice constant, and hence, find the critical epitaxial thickness for which Ni80Fe20 grows pseudomorphically on Cu (100). XTEM analysis indicated that the epitaxial films had atomically-abrupt interfaces which was not the case for polycrystalline Cu and Ni80Fe20 film interfaces. The Magnetic properties of these epitaxial films were Measured in situ using Magneto-optic Kerr effect magnetometry and were compared with those of polycrystalline films grown on SiO2/Si. Large Hc (∼ 35 Oe) was observed for epitaxial Ni80Fe20 films less than 3.0 nm thick whereas for increasing thickness, Hc decreased approximately monotonically to a few Oersteds. Correlations were made between magnetic properties of these epitaxial films, the strain in the film and the interface roughness obtained from XTEM analysis.

A Critical Comparison of the Techniques used to Characterize the Crystallography of an Interface: Pd on mbe “Rown GaAs(100)

1984 ◽  
Vol 37 ◽  
Author(s):  
I. P. Delrue ◽  
M. Wittmer ◽  
T. S. Kuan ◽  
R. Ludeke
Keyword(s):  
Electron Diffraction ◽  
High Energy ◽  
Hexagonal Structure ◽  
Ex Situ ◽  
Epitaxial Relationship ◽  
Ion Channeling ◽  
Transmission Electron ◽  
Pronounced Reduction

AbstractIn situ Reflection High Energy Electron Diffraction and ex-situ Transmission Electron Diffraction and Ion Channeling have been applied to a reacted Pd-GaAs interface and the results obtained are critically compared. The investigation has been done on the stabilized c(2×8) surface obtained by MBE on GaAs(100) substrates. Smooth surface epitaxial growth has been observed by RHEED as soon as a few monolayers of Pd are deposited at a substrate temperature of about 325°C. TEM diffraction studies indicate the presence of an intermetallic hexagonal structure similar to the orthorhombic Pd5Ga2 but with slightly different lattice parameters due to the possible incorporation of As. A less abundant phase was also identified as an hexagonal structure similar to Pd8As2. Ion Channeling indicates pronounced reduction in scattering yield when the [100] axis of the substrate was aligned with the impinging beam, thus supporting the RHEED analysis. The three techniques listed above were found to be useful for the determination of the epitaxial relationship between the identified phases and the substrate.

Transmission Electron Microscopy of Epitaxial silicides grown by ultra high vacuum deposition

1989 ◽  
Vol 47 ◽  
pp. 462-463
Author(s):  
D. Loretto ◽  
J. M. Gibson ◽  
S. M. Yalisove
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Electron Diffraction ◽  
High Vacuum ◽  
High Energy ◽  
Energy Electron ◽  
Ultra High Vacuum ◽  
Ex Situ ◽  
Transmission Electron

The silicides CoSi2 and NiSi2 are both metallic with the fee flourite structure and lattice constants which are close to silicon (1.2% and 0.6% smaller at room temperature respectively) Consequently epitaxial cobalt and nickel disilicide can be grown on silicon. If these layers are formed by ultra high vacuum (UHV) deposition (also known as molecular beam epitaxy or MBE) their thickness can be controlled to within a few monolayers. Such ultrathin metal/silicon systems have many potential applications: for example electronic devices based on ballistic transport. They also provide a model system to study the properties of heterointerfaces. In this work we will discuss results obtained using in situ and ex situ transmission electron microscopy (TEM).In situ TEM is suited to the study of MBE growth for several reasons. It offers high spatial resolution and the ability to penetrate many monolayers of material. This is in contrast to the techniques which are usually employed for in situ measurements in MBE, for example low energy electron diffraction (LEED) and reflection high energy electron diffraction (RHEED), which are both sensitive to only a few monolayers at the surface.

A New Method of Wafer Level Plan View TEM Sample Preparation by DualBeam

2008 ◽  
Author(s):  
Hyoung H. Kang ◽  
Michael A. Gribelyuk ◽  
Oliver D. Patterson ◽  
Steven B. Herschbein ◽  
Corey Senowitz
Keyword(s):  
Sample Preparation ◽  
Ex Situ ◽  
Wafer Level ◽  
Cross Sectional ◽  
Plan View ◽  
Manufacturing Line ◽  
Transmission Electron ◽  
Thin Lamella ◽  
Preparation Techniques

Abstract Cross-sectional style transmission electron microscopy (TEM) sample preparation techniques by DualBeam (SEM/FIB) systems are widely used in both laboratory and manufacturing lines with either in-situ or ex-situ lift out methods. By contrast, however, the plan view TEM sample has only been prepared in the laboratory environment, and only after breaking the wafer. This paper introduces a novel methodology for in-line, plan view TEM sample preparation at the 300mm wafer level that does not require breaking the wafer. It also presents the benefit of the technique on electrically short defects. The methodology of thin lamella TEM sample preparation for plan view work in two different tool configurations is also presented. The detailed procedure of thin lamella sample preparation is also described. In-line, full wafer plan view (S)TEM provides a quick turn around solution for defect analysis in the manufacturing line.

Temperature Dependent Quasi-Periodic Facetting of AlAs Grown by MBE on (100) GaAs Substrates

1993 ◽  
Vol 312 ◽  
Author(s):  
Richard Mirin ◽  
Mohan Krishnamurthy ◽  
James Ibbetson ◽  
Arthur Gossard ◽  
John English ◽  
...  
Keyword(s):  
Growth Conditions ◽  
High Energy ◽  
High Energy Electron ◽  
Temperature Dependent ◽  
Cross Sectional ◽  
Mbe Growth ◽  
Atomic Force ◽  
Gaas Substrates ◽  
Transmission Electron ◽  
Facet Formation

AbstractHigh temperature (≥ 650°C) MBE growth of AlAs and AlAs/GaAs superlattices on (100) GaAs is shown to lead to quasi-periodic facetting. We demonstrate that the facetting is only due to the AlAs layers, and growth of GaAs on top of the facets replanarizes the surface. We show that the roughness between the AlAs and GaAs layers increases with increasing number of periods in the superlattice. The roughness increases to form distinct facets, which rapidly grow at the expense of the (100) surface. Within a few periods of the initial facet formation, the (100) surface has disappeared and only the facet planes are visible in cross-sectional transmission electron micrographs. At this point, the reflection high-energy electron diffraction pattern is spotty, and the specular spot is a distinct chevron. We also show that the facetting becomes more pronounced as the substrate temperature is increased from 620°C to 710°C. Atomic force micrographs show that the valleys enclosed by the facets can be several microns long, but they may also be only several nanometers long, depending on the growth conditions.

Low Temperature Silicon Epitaxial Growth by Plasma Enhanced Chemical Vapor Deposition From SiH4/He/H2

1991 ◽  
Vol 235 ◽  
Author(s):  
Yung-Jen Lin ◽  
Ming-Deng Shieh ◽  
Chiapying Lee ◽  
Tri-Rung Yew
Keyword(s):  
Electron Microscopy ◽  
Chemical Vapor Deposition ◽  
Epitaxial Growth ◽  
Vapor Deposition ◽  
Chemical Vapor ◽  
Ex Situ ◽  
Epitaxial Layers ◽  
Cross Sectional ◽  
Transmission Electron

ABSTRACTSilicon epitaxial growth on silicon wafers were investigated by using plasma enhanced chemical vapor deposition from SiH4/He/H2. The epitaxial layers were growm at temperatures of 350°C or lower. The base pressure of the chamber was greater than 2 × 10−5 Torr. Prior to epitaxial growth, the wafer was in-situ cleaned by H2 baking for 30 min. The epi/substrate interface and epitaxial layers were observed by cross-sectional transmission electron microscopy (XTEM). Finally, the influence of the ex-situ and in-situ cleaning processes on the qualities of the interface and epitaxial layers was discussed in detail.

Orientational and Microstructural Evolution During Epitaxial Growth of Cu on Si(001) by Sputter Deposition

1992 ◽  
Vol 280 ◽  
Author(s):  
I. Hashim ◽  
B. Park ◽  
H. A. Atwater
Keyword(s):  
Epitaxial Growth ◽  
Ion Beam ◽  
High Energy ◽  
Sputter Deposition ◽  
X Ray Diffraction ◽  
Cross Sectional ◽  
Plan View ◽  
Transmission Electron

ABSTRACTEpitaxial Cu thin films have been grown on H-terminated Si(OOl) substrates at room temperature by D.C. ion-beam sputter deposition in ultrahigh vacuum. The development of orientation and microstructure during epitaxial growth from the initial stages of Cu growth up to Cu thicknesses of few hundred nm has been investigated. Analysis by in-situ reflection high energy electron diffraction, thin film x-ray diffraction, and plan-view and cross-sectional transmission electron microscopy indicates that the films are well textured with Cu(001)∥ Si(001) and Cu[100]∥ Si[110]. Interestingly, it is found that a distribution of orientations occurs at the early stages of Cu epitaxy on Si(001) surface, and that a (001) texture emerges gradually with increasing Cu thickness. The effect of silicide formation and deposition conditions on the crystalline quality of Cu epitaxy is also discussed.

Low Temperature Silicon Epitaxial Growth by Plasma Enhanced Chemical Vapor Deposition from SiH4/He/H2

1991 ◽  
Vol 236 ◽  
Author(s):  
Yung-Jen Lin ◽  
Ming-Deng Shieh ◽  
Chiapying Lee ◽  
Tri-Rung Yew
Keyword(s):  
Electron Microscopy ◽  
Chemical Vapor Deposition ◽  
Epitaxial Growth ◽  
Vapor Deposition ◽  
Chemical Vapor ◽  
Ex Situ ◽  
Epitaxial Layers ◽  
Cross Sectional ◽  
Transmission Electron

AbstractSilicon epitaxial growth on silicon wafers were investigated by using plasma enhanced chemical vapor deposition from SiH4/He/H2. The epitaxial layers were growm at temperatures of 350°C or lower. The base pressure of the chamber was greater than 2 × 10−5 Torr. Prior to epitaxial growth, the wafer was in-situ cleaned by H2 baking for 30 min. The epi/substrate interface and epitaxial layers were observed by cross-sectional transmission electron microscopy (XTEM). Finally, the influence of the ex-situ and in-situ cleaning processes on the qualities of the interface and epitaxial layers was discussed in detail.

In situ and ex situ transmission electron microscopy investigation of Cu–Al–Cu–Ti reactive metallic multilayer coatings

2010 ◽  
Vol 25 (6) ◽  
pp. 1196-1203 ◽  
Author(s):  
M.A. Mat Yajid ◽  
H. Bagshaw ◽  
G. Möbus
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Ex Situ ◽  
Alloy Formation ◽  
Cross Sectional ◽  
Multilayer Systems ◽  
Transmission Electron ◽  
Reactive Sample ◽  
In Situ Heating

Metallic multilayers of Cu/Al/Ti composition were studied by transmission electron microscopy (TEM) and plasmon energy-loss mapping as prototypes of nanoscale reactive multilayer systems with exothermic alloy formation in oxygen-free conditions. The selection and arrangement of alloy phases by the system during ex situ and in situ heating experiments were found to depend not only on temperature but strongly on the initial volume ratios of metals, and to a lesser degree on the dimensionality of the reactive sample. Here, a two-dimensional sample was represented by ex situ heating of the full multilayer structure, a one-dimensional sample refers to in situ heating of thin cross-sectional TEM specimens, while a zero-dimensional sample (or metallic dot-array) was obtained after cutting thin pillars using focused ion beams. Lamellar self-organized alternation between Heusler phase and Cu9Al4 was found.

A TEM study of low-temperature Ge growth on Ge(001)2×1

1993 ◽  
Vol 51 ◽  
pp. 804-805
Author(s):  
H.Z. Xiao ◽  
G. Xue ◽  
I.M. Robertson ◽  
H.K. Birnbaum ◽  
J.E. Greene
Keyword(s):  
Low Temperature ◽  
High Energy ◽  
Group Iv ◽  
Cross Sectional ◽  
Mbe Growth ◽  
Group Iv Semiconductors ◽  
Transmission Electron ◽  
And Control ◽  
Post Deposition

One approach to a solution of the doping problem in the molecular beam epitaxy (MBE) growth of the group IV semiconductors, e.g., segregation, low incorporation, and control of the dopants, is to lower the growth temperatures. It has been found that the room temperature Si deposition becomes amorphous after growth of a limiting epitaxial thickness which increases rapidly with the growth temperature. However, the mechanism for this structural transition is not well understood. In the present paper, we report the preliminary results of a study on the mechanism of the low temperature MBE growth of Ge on Ge(001)2×1 over the temperature range of 20-100 °C at deposition rates R=0.05 and 0.1 nm s−1 in an MBE system which has a bass pressure of 5xl0−11 Torr which increases to about 2xl0−9 Torr during deposition. The structural transitions were investigated using a combination of in-situ reflection high-energy electron diffraction (RHEED) and post-deposition high resolution cross-sectional transmission electron microscopy (XTEM).

Sign in / Sign up

Export Citation Format

Share Document