Superparamagnetic Behavior of Granular Co-C Films Consisting of Nanocrystalline Cobalt Encapsulated in Carbon

2000 ◽  
Vol 614 ◽  
Author(s):  
Hao Wang ◽  
S.P. Wong ◽  
W.Y. Cheung ◽  
N. Ke ◽  
M.F. Chiah ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Rutherford Backscattering Spectrometry ◽  
Magnetic Measurements ◽  
Magnetic Hysteresis ◽  
Blocking Temperature ◽  
Vacuum Arc ◽  
Zero Field ◽  
X Ray Diffraction ◽  
X Ray ◽  
Force Microscopy

ABSTRACTNanocomposite Co-C thin films of about 15 nm thick were prepared by pulsed filtered vacuum arc deposition. The films were characterized by x-ray photoelectron spectroscopy, non-Rutherford backscattering spectrometry, x-ray diffraction, magnetic force microscopy and magnetic measurements. The as-deposited films were amorphous. After annealing at 350°C for one hour in vacuum (< 10−3 Pa), the films were found to consist of nanocrystalline Co grains encapsulated in carbon. The superparamagnetism of the annealed Co36C64 film was demonstrated by the measurement of DC susceptibility and magnetic hysteresis using a SQUID magnetometer. The superparamagnetic relaxation blocking temperature was marked to be about 12K by the peak of the zero-field-cooled magnetization under a field of 100 Oe. The magnetic properties of these annealed granular Co-C films transform from superparamagnetism to ferromagnetism when the Co concentration increases.

Investigation of the Effect of Uv-Assisted Oxidation and Nitridation of Hafnium Metal Films

2003 ◽  
Vol 780 ◽  
Author(s):  
C. Essary ◽  
V. Craciun ◽  
J. M. Howard ◽  
R. K. Singh
Keyword(s):  
Uv Radiation ◽  
Photoelectron Spectroscopy ◽  
Grazing Angle ◽  
X Ray Diffraction ◽  
Metal Thin Films ◽  
X Ray ◽  
Force Microscopy ◽  
Si Substrates ◽  
Atomic Force ◽  
Silicon Interface

AbstractHf metal thin films were deposited on Si substrates using a pulsed laser deposition technique in vacuum and in ammonia ambients. The films were then oxidized at 400 °C in 300 Torr of O2. Half the samples were oxidized in the presence of ultraviolet (UV) radiation from a Hg lamp array. X-ray photoelectron spectroscopy, atomic force microscopy, and grazing angle X-ray diffraction were used to compare the crystallinity, roughness, and composition of the films. It has been found that UV radiation causes roughening of the films and also promotes crystallization at lower temperatures.Furthermore, increased silicon oxidation at the interface was noted with the UVirradiated samples and was shown to be in the form of a mixed layer using angle-resolved X-ray photoelectron spectroscopy. Incorporation of nitrogen into the film reduces the oxidation of the silicon interface.

Characterization of X-ray irradiated graphene oxide coatings using X-ray diffraction, X-ray photoelectron spectroscopy, and atomic force microscopy

2013 ◽  
Vol 28 (2) ◽  
pp. 68-71 ◽  
Author(s):  
Thomas N. Blanton ◽  
Debasis Majumdar
Keyword(s):  
Atomic Force Microscopy ◽  
Graphene Oxide ◽  
Photoelectron Spectroscopy ◽  
High Energy ◽  
X Ray Diffraction ◽  
Carbon Phase ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Before And After

In an effort to study an alternative approach to make graphene from graphene oxide (GO), exposure of GO to high-energy X-ray radiation has been performed. X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and atomic force microscopy (AFM) have been used to characterize GO before and after irradiation. Results indicate that GO exposed to high-energy radiation is converted to an amorphous carbon phase that is conductive.

Improved Functional Capabilities of Quasi-Two-Dimensional Tungsten Oxide Nanostructures

2016 ◽  
Vol 689 ◽  
pp. 55-59
Author(s):  
Serge Zhuiykov
Keyword(s):  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Current Sensing ◽  
X Ray ◽  
Force Microscopy ◽  
Functional Capabilities ◽  
Atomic Force ◽  
Oxide Nanostructures ◽  
Afm Analysis

Electrical properties and morphology of orthorhombic β–WO3 nano-flakes with thickness of ~7-9 nm were investigated at the nanoscale using energy dispersive X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and current sensing force spectroscopy atomic force microscopy (CSFS-AFM, or PeakForce TUNATM). CSFS-AFM analysis established good correlation between the topography of the developed nanostructures and various features of WO3 nano-flakes synthesized via a two-step sol-gel-exfoliation method. It was determined that β–WO3 nano-flakes annealed at 550°C possess distinguished and exceptional thickness-dependent properties in comparison with the bulk, micro- and nano-structured WO3 synthesized at alternative temperatures.

Epitaxial BaTiO3 Thin Films on Different Substrates for Optical Waveguide Applications

1999 ◽  
Vol 597 ◽  
Author(s):  
M. Siegert ◽  
Judit G. Lisoni ◽  
C. H. Lei ◽  
A. Eckau ◽  
W. Zander ◽  
...  
Keyword(s):  
Thin Films ◽  
Optical Waveguides ◽  
Rutherford Backscattering Spectrometry ◽  
Optical Data ◽  
X Ray Diffraction ◽  
X Ray ◽  
Force Microscopy ◽  
Ion Channeling ◽  
Atomic Force ◽  
Transmission Electron

AbstractIn the process of developing thin film electro-optical waveguides we investigated the influence of different substrates on the optical and structural properties of epitaxial BaTiO3 thin films. These films are grown by on-axis pulsed laser deposition (PLD) on MgO(100), MgAl2O4(100), SrTiO3(100) and MgO buffered A12O3(1102) substrates. The waveguide losses and the refractive indices were measured with a prism coupling setup. The optical data are correlated to the results of Rutherford backscattering spectrometry/ion channeling (RBS/C). X-ray diffraction (XRD), atomic force microscopy (AFM) and transmission electron microscopy (TEM). BaTiO3 films on MgO(100) substrates show planar waveguide losses of 3 dB/cm and ridge waveguide losses of 5 dB/cm at a wavelength of 633 nm.

scholarly journals Iron-Doped Lithium Tantalate Thin Films Deposited by Magnetron Sputtering: A Study of the Iron Role in the Structure and the Derived Magnetic Properties

Crystals ◽  
2020 ◽  
Vol 10 (1) ◽  
pp. 50 ◽  
Author(s):  
Sergio David Villalobos Mendoza ◽  
José Trinidad Holguín Momaca ◽  
José Trinidad Elizalde Galindo ◽  
Diana María Carrillo Flores ◽  
Sion Federico Olive Méndez ◽  
...  
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Magnetic Hysteresis ◽  
Hysteresis Loops ◽  
Blocking Temperature ◽  
Ferromagnetic Behavior ◽  
Zero Field ◽  
Cooling Curves ◽  
X Ray Diffraction ◽  
Field Cooling

Fe-doped LiTaO3 thin films with a low and high Fe concentration (labeled as LTO:Fe-LC and LTO:Fe-HC, respectively) were deposited by magnetron sputtering from two home-made targets. The dopant directly influenced the crystalline structure of the LiTaO3 thin films, causing the contraction of the unit cell, which was related to the incorporation of Fe3+ ions into the LiTaO3 structure, which occupied Li positions. This substitution was corroborated by Raman spectroscopy, where the bands associated with Li-O bonds broadened in the spectra of the samples. Magnetic hysteresis loops, zero-field cooling curves, and field cooling curves were obtained in a vibrating sample magnetometer. The LTO:Fe-HC sample demonstrates superparamagnetic behavior with a blocking temperature of 100 K, mainly associated with the appearance of Fe clusters in the thin film. On the other hand, a room temperature ferromagnetic behavior was found in the LTO:Fe-LC layer where saturation magnetization (3.80 kAm−1) and magnetic coercivities were not temperature-dependent. Moreover, the crystallinity and morphology of the samples were evaluated by X-ray diffraction and scanning electron microscopy, respectively.

Stress origin and relaxation in epitaxial AlN thin films on SiC

2001 ◽  
Vol 696 ◽  
Author(s):  
Ravi Bathe ◽  
R.D. Vispute ◽  
Daniel Habersat ◽  
R. P. Sharma ◽  
T. Venkatesan ◽  
...  
Keyword(s):  
Thin Films ◽  
Rutherford Backscattering Spectrometry ◽  
Wide Band ◽  
X Ray Diffraction ◽  
Wide Band Gap ◽  
X Ray ◽  
Force Microscopy ◽  
Ion Channeling ◽  
Atomic Force ◽  
Highly Strained

AbstractWe have investigated the epitaxy, surfaces, interfaces, and defects in AlN thin films grown on SiC by pulsed laser deposition. The stress origin, evolution, and relaxation in these films is reported. The crystalline structure and surface morphology of the epitaxially grown AlN thin films on SiC (0001) substrates have been studied using x-ray diffraction (θ–2θ, ω, and Ψ scans) and atomic force microscopy, respectively. The defect analysis has been carried out by using Rutherford backscattering spectrometry and ion channeling technique. The films were grown at various substrate temperatures ranging from room temperature to 1100 °C. X-ray diffraction measurements show highly oriented AlN films when grown at temperatures of 750- 800 °C, and single crystals above 800 °C. The films grown in the temperature range of 950 °C to 1000 °C have been found to be highly strained, whereas the films grown above 1000 °C were found to be cracked along the crystallographic axes. The results of stress as a function of growth temperature, thermal mismatch, growth mode, and buffer layer thickness will be presented, and the implications of these results for wide band gap power electronics will be discussed.

Magnetic cluster developement in In1−x MnxSb semiconductor alloys

Open Physics ◽  
2010 ◽  
Vol 8 (4) ◽  
Author(s):  
Lidia Rednic ◽  
Iosif Deac ◽  
Eugen Dorolti ◽  
Marin Coldea ◽  
Vasile Rednic ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Magnetic Measurements ◽  
Semiconductor Alloys ◽  
X Ray Diffraction ◽  
Magnetic Cluster ◽  
X Ray ◽  
Small Magnetic Field ◽  
Transmission Electron

AbstractX-ray Diffraction (XRD), X-ray Photoelectron Spectroscopy (XPS), Transmission Electron Microscopy (TEM) and magnetic measurements as a function of applied magnetic field and temperature for In1−x MnxSb (0.05≤x≤0.2) system are reported. Magnetic measurements performed at high and small magnetic field in ZFC and FC indicate the coexistence of ferromagnetic In1−x MnxSb solid solution and two types of magnetic cluster: ferromagnetic MnSb and ferrimagnetic Mn2Sb. XPS valence band and Mn 2p core level spectra have confirmed the presence of MnSb and Mn2Sb phases. TEM images show some manganese antimonide phase microinclusions with dimension between (30–40) nm.

STUDIES ON SURFACE STRUCTURE, MORPHOLOGY AND COMPOSITION OF Co–W COATINGS ELECTRODEPOSITED WITH DIRECT AND PULSE CURRENT USING GLUCONATE BATH

2013 ◽  
Vol 20 (01) ◽  
pp. 1350006 ◽  
Author(s):  
PARTHASARATHI BERA ◽  
H. SEENIVASAN ◽  
K. S. RAJAM
Keyword(s):  
Photoelectron Spectroscopy ◽  
Pulse Current ◽  
Diffraction Field ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Force Microscopy ◽  
Dsc Studies ◽  
Atomic Force ◽  
Electrodeposited Coating

Co–W alloy coatings were deposited with direct current (DC) and pulse current (PC) electrodeposition methods using gluconate bath at pH5 and characterized by X-ray diffraction, field emission scanning electron microscopy, atomic force microscopy, differential scanning calorimetry (DSC) and X-ray photoelectron spectroscopy (XPS). DSC studies hint at the possibility of formation of metallic glasses. Detailed XPS studies of these alloy coatings have been carried out to compare elemental states and composition of Co and W in DC and PC electrodeposited alloys. DC-plated alloy has significant amount of Co and W metal along with their respective oxidized species. In contrast, mainly oxidized metals are present in the following layers of as-deposited coatings prepared with PC plating. Concentration of Co metal is observed to increase during sputtering, whereas there is no change in W6+ concentration. Microhardness measurement of all the Co–W coatings shows higher hardness compared to Co metal and 1:1 and 1:4 PC electrodeposited coatings show little higher hardness compared to 1:2 PC electrodeposited coating.

scholarly journals Electronic and vibrational decoupling in chemically exfoliated bilayer 2D-V2O5

2021 ◽  
Author(s):  
Reshma P R ◽  
Anees Pazhedath ◽  
Ganesan Karuppiah ◽  
Arun Prasad ◽  
Sandip Dhara
Keyword(s):  
Transition Metal ◽  
Photoelectron Spectroscopy ◽  
Density Functional ◽  
Blue Shift ◽  
X Ray Diffraction ◽  
Phonon Modes ◽  
Visible Absorption ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force

Abstract Recently emerged transition metal oxide (TMO) based 2D nanostructures are gaining a foothold in advanced applications. Unlike, 2D transition metal dichalchogenides, it is strenuous to obtain high quality thin TMOs due to exotic surface reconstruction during synthesis. Herein, we report the synthesis of bilayer thin 2D-V2O5 nanosheets using chemical exfoliation. Synchrotron X-ray diffraction, X-ray photoelectron spectroscopy and atomic force microscopy substantiate the successful formation of bilayer thin 2D-V2O5. Ultraviolet-visible absorption spectra exhibit a thickness dependent blue shift in the optical band gap, signifying the emergence of electronic decoupling. Raman spectroscopy fingerprinting shows a thickness dependent vibrational decoupling of phonon modes. Further, it has been verified by computing the lattice vibrational modes using density functional perturbation theory. In this study, the manifestation of the electronic and vibrational decoupling is used as a novel probe to confirm the successful exfoliation of bilayer 2D-V2O5 from its bulk counterpart.

Sign in / Sign up

Export Citation Format

Share Document