Bioceramics and Biominerals and Their Nanostructures

2001 ◽  
Vol 676 ◽  
Author(s):  
Shulin Wen ◽  
Jingwei Feng
Keyword(s):  
Chemical Composition ◽  
High Strength ◽  
Layered Composite ◽  
Chemical Formula ◽  
Human Teeth ◽  
High Toughness ◽  
Ti Oxides ◽  
Human Bones ◽  
Composition And Structure ◽  
Better Than

ABSTRACTArtificial hydroxyapatite with chemical formula of Ca10(PO4)6(OH)2 is the best as bioceramics due to its composition and structure being similar with inorganic part of hard tissues. The alloys especially with Ti, Ni and Co contents are very promising as a kind of biomaterials due to their high strength and high toughness. The alloys as biomaterials need good final surface properties by proper surface treatment. By using clinical treatment with machining, cleaning, sterilization, we obtained Ti-oxides surface with 4-6 nm in thickness which are very good in property with chemical composition of TiO2 + Ti2O3 + TiO. However, the Ti-alloy with an artificial hydroxyapatite surface is even much better than that with the surface of Ti-oxides due to its high bioactivity. Human bones and human teeth with a chemical composition of Ca10(PO4)6(OH)2 and the structure of hydroxyapatite are commonly considered as bio-mineral. In nature the pears and shells are also a kind of bio-minerals. Our observations showed that human bone is a complex material with a layered composite structure. The hydroxyapatite mineral crystals that reinforce the organic proteinceous component are about 35 nm wide, irregular, plate-like crystals reside initially in the hole zones of the collagen microfibris: later fill available space within the collagen fibrils. At present paper nanostructure features of both bioceramics and biominerals have been characterized with comparison between each other's.

Production of as-Cast High Strength Toughness Ductile Iron

2012 ◽  
Vol 535-537 ◽  
pp. 533-537 ◽  
Author(s):  
Meng Li
Keyword(s):  
Chemical Composition ◽  
Production Process ◽  
Ductile Iron ◽  
High Strength ◽  
High Toughness

The paper has mainly reviewed the production process of as-cast high toughness ductile iron, analysing the effects of chemical composition, desulphurization process, nodulizing process and the craft of inoculation on the production of as-cast high toughness ductile iron.

Application Feasibility Study of High Strength Pipeline Steel to Rig Derrick and Substructure

2020 ◽  
Vol 993 ◽  
pp. 616-621
Author(s):  
Fang Po Li ◽  
Zhi Wei Zhang ◽  
Bin Zhang
Keyword(s):  
Chemical Composition ◽  
Service Property ◽  
Pipeline Steel ◽  
High Strength ◽  
Working Environment ◽  
Technical Requirement ◽  
Micro Structure ◽  
Service Environment ◽  
Technical Requirements ◽  
Better Than

Derrick and substructure is one of rig’s core equipment components, and it is also the most important weight component of rig. The working environment of derrick and substructure is very serious, whose material should has high strength, excellent plasticity, toughness and weldability property. In this paper, the chemical composition, micro-structure, tensile property, impact property, hardness and weldability of high strength pipeline steel with strength grades of X70 (485MPa)~ X100(690MPa) were systematically analyzed. The analysis and study of the service environment of rig derrick and substructure as well as the technical requirements of the material, showed that the performance of high strength pipeline steel was obviously better than that of the same grade high strength low alloy structural steel used in rig derrick and substructure at present, and it can fully meet the technical requirement of rig derrick and substructure. The application of high strength pipeline steel to rig derrick and substructure will improve the service property, optimize the design , and fully ensure the service safety of rig derrick and substructure.

Survey of Relations of Chemical Constituents in Polymer-Based Materials with Brittleness and its Associated Properties

2016 ◽  
Vol 10 (4s) ◽  
pp. 595-600 ◽  
Author(s):  
Witold Brostow ◽  
◽  
Haley E. Hagg Lobland ◽  
Keyword(s):  
Chemical Composition ◽  
Impact Strength ◽  
Free Volume ◽  
Chemical Constituents ◽  
Polymer Processing ◽  
Brittle Behavior ◽  
Composition And Structure ◽  
Common Thread

The property of brittleness for polymers and polymer-based materials (PBMs) is an important factor in determining the potential uses of a material. Brittleness of polymers may also impact the ease and modes of polymer processing, thereby affecting economy of production. Brittleness of PBMs can be correlated with certain other properties and features of polymers; to name a few, connections to free volume, impact strength, and scratch recovery have been explored. A common thread among all such properties is their relationship to chemical composition and morphology. Through a survey of existing literature on polymer brittleness specifically combined with relevant reports that connect additional materials and properties to that of brittleness, it is possible to identify chemical features of PBMs that are connected with observable brittle behavior. Relations so identified between chemical composition and structure of PBMs and brittleness are described herein, advancing knowledge and improving the capacity to design new and to choose among existing polymers in order to obtain materials with particular property profiles.

DILLIMAX 500

Alloy Digest ◽  
2012 ◽  
Vol 61 (3) ◽  
Keyword(s):  
Fracture Toughness ◽  
Yield Strength ◽  
Physical Properties ◽  
Structural Steel ◽  
Tensile Properties ◽  
High Strength ◽  
Heat Treating ◽  
Fine Grained ◽  
High Toughness ◽  
Minimum Yield

Abstract Dillimax 500 is a high-strength quenched and tempered, fine-grained structural steel with a minimum yield strength of 500 MPa (72 ksi). Plate is delivered in three qualities: basic, high toughness, and extra tough. This datasheet provides information on composition, physical properties, and tensile properties as well as fracture toughness. It also includes information on surface qualities as well as forming, heat treating, and joining. Filing Code: SA-645. Producer or source: Dillinger Hütte GTS.

SPARTAN II

Alloy Digest ◽  
2016 ◽  
Vol 65 (1) ◽  
Keyword(s):  
Yield Strength ◽  
Physical Properties ◽  
Tensile Properties ◽  
High Strength ◽  
Low Carbon ◽  
Copper Precipitation ◽  
High Toughness ◽  
The Family ◽  
Alloy Steels ◽  
Minimum Yield

Abstract SPARTAN II (HSLA-100) is one of the family of Spartan high strength (>690 MPa, or >100 ksi, minimum yield strength), high toughness, improved weldability steels, which are alternatives to traditional quenched and tempered alloy steels. The Spartan family of steels are low carbon, copper precipitation hardened steels. Spartan II has improved yield strength compared to Spartan I. This datasheet provides information on composition, physical properties, microstructure, tensile properties. It also includes information on forming and joining. Filing Code: SA-738. Producer or source: ArcelorMittal USA.

TLS S1

Alloy Digest ◽  
2007 ◽  
Vol 56 (9) ◽  
Keyword(s):  
Fracture Toughness ◽  
Wear Resistance ◽  
Physical Properties ◽  
Carbon Content ◽  
High Strength ◽  
Heat Treating ◽  
High Toughness

Abstract The carbon content in TLS S1, about 0.5%, produces a combination of high strength and high toughness with medium wear resistance. Chisels and rivet sets are typical applications. This datasheet provides information on composition, physical properties, hardness, and elasticity as well as fracture toughness. It also includes information on wear resistance as well as heat treating and machining. Filing Code: TS-655. Producer or source: Timken Latrobe Steel.

Structure and chemical composition of exopolysaccharides of frost-damaged sugar beet

2020 ◽  
pp. 34-39
Author(s):  
Aneta Antczak-Chrobot ◽  
Maciej Wojtczak
Keyword(s):  
Spectral Analysis ◽  
Chemical Composition ◽  
Sugar Beet ◽  
Total Acid ◽  
Average Molecular Mass ◽  
Central European ◽  
Composition And Structure ◽  
Monomeric Composition ◽  
Branched Structure ◽  
Different Origin

In this research paper, development of a procedure of isolation of exopolysaccharides from frost-damaged beet and an analysis of structural and chemical composition of polymers isolated from sugar beet of different origin are presented. Total acid hydrolysis degradation integrated with HPAEC-ED analysis has been utilized to confirm the monomeric composition of the separated polysaccharides. The implementation of NMR spectral analysis and SEC chromatography of the structure of exopolysaccharides has been investigated. The results demonstrate that the chemical composition and structure of exopolysaccharides depend on their origin. Typical exopolysaccharides from Central European beet roots consist mainly of glucose monomers – and they have low branched structure – about 90% of α-1,6 linkage which is typical for dextran. The exopolysaccharides isolated from Swedish beet are characterized by 50–60% fructose monomers. They contain only about 65% α-1,6 linkages. Exopolysaccharides extracted from various origin beet differ in average molecular mass. The molecular distribution is not normal.

Sign in / Sign up

Export Citation Format

Share Document