Reactivity of Silicates 1. Kinetic Studies of the Hydrolysis of Linear and Cyclic Siloxanes as Models for Defect Structure in Silicates

1986 ◽  
Vol 73 ◽  
Author(s):  
Carol A. Balfe ◽  
Kenneth J. Ward ◽  
David R. Tallant ◽  
Sheryl L. Martinez
Keyword(s):  
Rate Constant ◽  
Kinetic Studies ◽  
Order Rate Constant ◽  
Hydrolysis Rate ◽  
Rate Data ◽  
Cyclic Siloxanes ◽  
Highly Strained ◽  
Kinetics Of ◽  
Hydrolysis Of ◽  
Tetrahydrofuran Solution

ABSTRACTThe kinetics of hydrolysis of hexamethylcyclotrisiloxane and di-t-butyldimesitylcyclodisiloxane in tetrahydrofuran solution have been determined and compared to hydrolysis rates of silica defects. In the presence of sufficient excess witer, the first-order rate constant of the cyclotrisiloxine, k= 3.8 × 10−3 min is similar to the rate constant, k = 5.2 × 10−1 min, of the disappearance of the D2 Raman silica defect band it has been proposed to model. Limited hydrolysis rate data for the cyclodisiloxane suggests that it hydrolyzes at least four times faster than does the cyclotrisiloxane. These data are consistent with rate data available for silica crack growth and support the assignment of highly strained siloxane bonds at the crack tip to cyclodisiloxanes. Infrared spectra determined for the cyclodisiloxanes lend further support to this model.

The mechanisms of hydrolysis of alkyl N-alkylthioncarbamate esters at 100 °C

2005 ◽  
Vol 83 (9) ◽  
pp. 1483-1491 ◽  
Author(s):  
Eduardo Humeres ◽  
Maria de Nazaré M. Sanchez ◽  
Conceição ML Lobato ◽  
Nito A Debacher ◽  
Eduardo P. de Souza
Keyword(s):  
Rate Constant ◽  
Order Rate Constant ◽  
Base Catalysis ◽  
Hydrolysis Rate ◽  
Negative Slope ◽  
General Base ◽  
Order Rate ◽  
Basic Hydrolysis ◽  
Rate Profile ◽  
Hydrolysis Of

The hydrolysis of ethyl N-ethylthioncarbamate (ETE) at 100 °C was studied in the range of 7 mol/L HCl to 4 mol/L NaOH. The pH–rate profile showed that the hydrolysis occurred through specific acid catalysis at pH < 2, spontaneous hydrolysis at pH 2–6.5, and specific basic catalysis at pH > 6.5. The Hammett acidity plot and the excess acidity plot against X were linear. The Bunnett–Olsen plot gave a negative slope indicating that the conjugate acid was less hydrated than the neutral substrate. It was concluded that the acid hydrolysis occurred by an A1 mechanism. The neutral species hydrolyzed with general base catalysis shown by the Brønsted plot with β = 0.48 ± 0.04. Water acted as a general base catalyst with (pseudo-)first-order rate constant, kN = 3.06 × 10–7 s–1. At pH > 6.5 the rate constants increased, reaching a plateau at high basicity. The basic hydrolysis rate constant of ethyl N,N-diethylthioncarbamate, which must react by a BAc2 mechanism, increased linearly at 1–3 mol/L NaOH with a second-order rate constant, k2 = 2.3 × 10–4 (mol/L)–1 s–1, which was 10 times slower than that expected for ETE. Experiments of ETE in 0.6 mol/L NaOH with an excess of ethylamine led to the formation of diethyl thiourea, presenting strong evidence that the basic hydrolysis occurred by the E1cb mechanism. In the rate-determining step, the E1cb mechanism involved the elimination of ethoxide ion from the thioncarbamate anion, producing an isothiocyanate intermediate that decomposed rapidly to form ethylamine, ethanol, and COS.Key words: alkylthioncarbamate esters, ethyl N-ethylthioncarbamate, ethyl N,N-diethylthioncarbamate, hydrolysis, mechanism.

The kinetics of the reaction of N,N-dimethyl-2-phenylaziridinium ion with bovine erythrocyte acetylcholinesterase

1970 ◽  
Vol 48 (3) ◽  
pp. 244-250 ◽  
Author(s):  
Jocelyn E. Purdie ◽  
R. M. Heggie
Keyword(s):  
Rate Constant ◽  
Order Rate Constant ◽  
Bovine Erythrocyte ◽  
Acidic Group ◽  
Ph Values ◽  
Order Rate ◽  
Decreasing Ph ◽  
Ph Range ◽  
Kinetics Of ◽  
Hydrolysis Of

The kinetics of the hydrolysis of N,N-dimethyl-2-phenylaziridinium ion (DPA) have been studied over the pH range 5.5–8.0 as have the kinetics of the interaction of DPA with bovine erythrocyte acetyl-cholinesterase. The enzyme is initially inhibited reversibly and subsequently irreversibly towards acetylcholine hydrolysis. The hydrolysis of DPA was found to be pH independent over the range studied while the reversible noncompetitive inhibition increased with increasing pH, the data suggesting the requirement for a basic group on the enzyme with a pKa of about 6.5.Between pH values of 6.0 and 8.0 the kinetics of the irreversible inhibition are consistent with either of two kinetically indistinguishable mechanisms, one involving transformation of the initial reversible complex and the other an independent attack on the uncomplexed enzyme. The first mechanism gives rise to a first-order rate constant which is comparable with that for the hydrolysis of DPA but which increases with decreasing pH; an acidic group on the enzyme with pKa between 6.0 and 7.0 may be involved. The second-order rate constant arising from the second treatment goes through a maximum at pH 7.3. At pH 5.5 the kinetics are not consistent with either mechanism.

Article

1999 ◽  
Vol 77 (5-6) ◽  
pp. 1005-1008
Author(s):  
Ayla Khan ◽  
Alexei A Neverov ◽  
Anatoly K Yatsimirsky ◽  
R S Brown
Keyword(s):  
Rate Constant ◽  
Metal Ion ◽  
Order Rate Constant ◽  
Water Proton ◽  
First Order ◽  
Catalytic Rate Constant ◽  
Equilibrium Binding ◽  
Metal Ion Catalysis ◽  
Kinetics Of ◽  
Hydrolysis Of

The kinetics of methanolysis of acetyl imidazole (1) and acetyl pyrazole (2) have been investigated under anhydrous conditions in the presence of Zn(ClO4)2, Co(ClO4)2, and HClO4 at 25°C. In all cases, the plots of the pseudo-first-order rate constant for methanolysis (kobs) vs. [metal ion] or [HClO4] show saturation behavior indicative of equilibrium binding of the M2+ or H+ to the amide. Relative to the spontaneous methanolysis rate constant (ko), the catalytic rate constant obtained at saturation, kcat, is larger for metal-ion catalysis than for H+ catalysis. The (kcatH+/ko) ratio is 10.7 and 1.25 for 1 and 2, respectively, while the (kcatM2+/ko) for these divalent metals varies from 150-fold for 1 to between 700 and 5700-fold for 2. By contrast, in water, proton is far more effective at promoting the hydrolysis of 1 than are metals, the aqueous (kcatH+/ko) ratio being 560, while the (kcatZn2+ /ko) and (kcatNi2+/ko) ratios are 15 and 3.2, respectively.Key words: methanolysis, kinetics, metal-ion catalysis, acetyl imidazole, acetyl pyrazole.

Kinetics of pyroarsenate hydrolysis in aqueous solution

1977 ◽  
Vol 30 (6) ◽  
pp. 1187 ◽  
Author(s):  
TG Richmond ◽  
JR Johnson ◽  
JO Edwards ◽  
PH Rieger
Keyword(s):  
Aqueous Solution ◽  
Rate Constant ◽  
Activation Parameters ◽  
Hydrolysis Rate ◽  
Associative Mechanism ◽  
Hydrolysis Rate Constant ◽  
Rate Of Hydrolysis ◽  
Ph Stat ◽  
Kinetics Of ◽  
Hydrolysis Of

The rate of hydrolysis of pyroarsenate in 0.1 mol dm-3 NaClO4 solutions, pH 6-9, was measured by a pH-stat technique at temperatures ranging from 278 to 298 K. The pKa of HAs2O73-, found to be the predominant reactant under these conditions, was 7.3 and 7.6 at 283 and 298 K, respectively. The hydrolysis rate constant for HAs2O73- was 0.05 s-1 at 298 K with activation parameters ΔH? = 49 � 9 kJ mol-1 and ΔS? = -107 � 30 J mol-1 K-1. An associative mechanism is indicated.

Oxidation of Nickel(II) and Manganese(II) by Peroxodisulfate in Aqueous Solution in the Presence of Molybdate. Crystal Structure of the (NH4)6[NiMo9O32].6H2O Product

1992 ◽  
Vol 45 (12) ◽  
pp. 1943 ◽  
Author(s):  
SJ Dunne ◽  
RC Burns ◽  
GA Lawrance
Keyword(s):  
Rate Constant ◽  
Linear Dependence ◽  
Ph Dependence ◽  
Order Rate Constant ◽  
X Ray Diffraction ◽  
X Ray ◽  
First Order ◽  
Oxidant Concentration ◽  
Ph Range ◽  
Kinetics Of

Oxidation of Ni2+,aq, by S2O82- to nickel(IV) in the presence of molybdate ion, as in the analogous manganese system, involves the formation of the soluble heteropolymolybdate anion [MMogO32]2- (M = Ni, Mn ). The nickel(IV) product crystallized as (NH4)6 [NiMogO32].6H2O from the reaction mixture in the rhombohedra1 space group R3, a 15.922(1), c 12.406(1) � ; the structure was determined by X-ray diffraction methods, and refined to a residual of 0.025 for 1741 independent 'observed' reflections. The kinetics of the oxidation were examined at 80 C over the pH range 3.0-5.2; a linear dependence on [S2O82-] and a non-linear dependence on l/[H+] were observed. The influence of variation of the Ni/Mo ratio between 1:10 and 1:25 on the observed rate constant was very small at pH 4.5, a result supporting the view that the precursor exists as the known [NiMo6O24H6]4- or a close analogue in solution. The pH dependence of the observed rate constant at a fixed oxidant concentration (0.025 mol dm-3) fits dequately to the expression kobs = kH [H+]/(Ka+[H+]) where kH = 0.0013 dm3 mol-1 s-1 and Ka = 4-0x10-5. The first-order dependence on peroxodisulfate subsequently yields a second-order rate constant of 0.042 dm3 mol-1 s-1. Under analogous conditions, oxidation of manganese(II) occurs eightfold more slowly than oxidation of nickel(II), whereas oxidation of manganese(II) by peroxomonosulfuric acid is 16-fold faster than oxidation by peroxodisulfate under similar conditions.

scholarly journals Kinetics of Enzymatic Hydrolysis of Southeast Sulawesi Sago Starch

2020 ◽  
pp. 53-61
Author(s):  
Ansharullah Ansharullah ◽  
Muhammad Natsir
Keyword(s):  
Enzymatic Hydrolysis ◽  
Maximum Velocity ◽  
Enzyme Concentration ◽  
Hydrolysis Rate ◽  
Sago Starch ◽  
Optimum Conditions ◽  
Kinetics Of ◽  
Hydrolysis Of ◽  
Substrate Concentrations ◽  
Menten Constant

The aims of this study were to characterize the kinetics of enzymatic hydrolysis of sago starch, obtained from Southeast Sulawesi Indonesia. The enzyme used for hydrolysis was bacterial ∝-amylase (Termamyl 120L from Bacillus licheniformis, E. C. 3.2.1.1).  The method to determine the initial velocity (Vo) of the hydrolysis was developed by differentiation a nonlinear equation (NLE).  The Vo of the hydrolysis was measured at various pH (6.0, 6.5,and 7.0), temperatures (40, 60, 75 and 95oC), enzyme concentrations (0.5, 1.0, 1.5 and 2.0 µg per mL) and in the presence of 70 ppm Ca++. The optimum conditions of this experiment were found to be at pH 6.5 – 7.0 and 75oC, and the Vo increased with increasing enzyme concentration. The Vo values at various substrate concentrations were also determined, which were then used to calculate the enzymes kinetics constant of the hydrolysis, including Michaelis-Menten constant (Km) and maximum velocity (Vmax) using a Hanes plot.  Km and Vmax values were found to be higher in the measurement at pH 7.0 and 75oC. The Km values  at four  different combinations of pH and temperatures (pH 6.5, 40oC; pH 6.5, 75oC; pH 7.0, 40oC; pH 7.0, 75oC) were found to be 0.86, 3.23, 0.77 and 3.83 mg/mL, respectively; and Vmax values were 17.5, 54.3, 20.3 and 57.1 µg/mL/min, respectively. The results obtained showed that hydrolysis rate of this starch was somewhat low.

scholarly journals Kinetics of the alkaline hydrolysis of crystal violet in micelles, reverse micelles and microemulsions of cetyltrimethylammonium bromide

1970 ◽  
Vol 24 (2) ◽  
pp. 173-184 ◽  
Author(s):  
Ferdousi Begum ◽  
Md Yousuf A Molla ◽  
M Muhibur Rahman ◽  
Md Abu Bin Hasan Susan
Keyword(s):  
Crystal Violet ◽  
Alkaline Hydrolysis ◽  
Reverse Micelles ◽  
Cetyltrimethylammonium Bromide ◽  
Specific Conductivity ◽  
Water System ◽  
Chemical Society ◽  
Order Rate Constant ◽  
Kinetics Of ◽  
Hydrolysis Of

Kinetics of the alkaline hydrolysis of crystal violet (CV) in micelles, reverse micelles and microemulsions of a cationic surfactant, cetyltrimethylammonium bromide (CTAB) was studied at 25 ± 0.1 oC using spectrophotometric method. The rate of alkaline hydrolysis of CV was catalyzed by micellar solutions of CTAB. The pseudo first order rate constant (k') has been found to decrease upon incorporation of 1-butanol to cationic CTAB micelles, which displaces the substrate from the micellar into the aqueous phase. In CTAB/cyclohexane/1-butanol/water system, as the content of 1-butanol increases, specific conductivity and density of the microemulsions and reverse micelles decrease. The change in physical properties also causes change in reaction environment. A change from a micelle-rich (o/w) to a reverse micelle-rich (w/o) condition is apparent for microemulsions and consequently the k' vs. % wt. of 1-butanol profiles show an initial decrease in the k' followed by a gradual increase and finally, to a sharp increase with increasing 1-butanol content. Microemulsions and reverse micelles thus offer the potential to control rate of a reaction by formation of micelles in water phase and reverse micelles in oil phase. DOI: http://dx.doi.org/10.3329/jbcs.v24i2.9706 Journal of Bangladesh Chemical Society, Vol. 24(2), 173-184, 2011

scholarly journals Kinetics of alkoxysilanes hydrolysis: An empirical approach

2019 ◽  
Vol 9 (1) ◽  
Author(s):  
Ahmed A. Issa ◽  
Marwa El-Azazy ◽  
Adriaan S. Luyt
Keyword(s):  
Reaction Mechanisms ◽  
Hydrolysis Reaction ◽  
Hydrolysis Rate ◽  
Coupling Agents ◽  
Linear Free Energy Relationship ◽  
Acidic Media ◽  
Linear Free Energy ◽  
Primary Materials ◽  
Kinetics Of ◽  
Hydrolysis Of

AbstractAlkoxysilanes and organoalkoxysilanes are primary materials in several industries, e.g. coating, anti-corrosion treatment, fabrication of stationary phase for chromatography, and coupling agents. The hydrolytic polycondensation reactions and final product can be controlled by adjusting the hydrolysis reaction, which was investigated under a variety of conditions, such as different alkoxysilanes, solvents, and catalysts by using gas chromatography. The hydrolysis rate of alkoxysilanes shows a dependence on the alkoxysilane structure (especially the organic attachments), solvent properties, and the catalyst dissociation constant and solubility. Some of the alkoxysilanes exhibit intramolecular catalysis. Hydrogen bonding plays an important role in the enhancement of the hydrolysis reaction, as well as the dipole moment of the alkoxysilanes, especially in acetonitrile. There is a relationship between the experimentally calculated polarity by the Taft equation and the reactivity, but it shows different responses depending on the solvent. It was found that negative and positive charges are respectively accumulated in the transition state in alkaline and acidic media. The reaction mechanisms are somewhat different from those previously suggested. Finally, it was found that enthalpy–entropy compensation (EEC) effect and isokinetic relationships (IKR) are exhibited during the hydrolysis of CTES in different solvents and catalysts; therefore, the reaction has a linear free energy relationship (LFER).

Kinetics of reconstitution of apotyrosinase by copper

1990 ◽  
Vol 68 (2) ◽  
pp. 476-479
Author(s):  
Donald C. Wigfield ◽  
Douglas M. Goltz
Keyword(s):  
Rate Constant ◽  
Copper Concentration ◽  
Copper Ions ◽  
Copper Ion ◽  
Order Rate Constant ◽  
First Order ◽  
Order Rate ◽  
Pseudo First Order ◽  
Rate Limiting ◽  
Kinetics Of

The kinetics of the reconstitution reaction of apotyrosinase with copper (II) ions are reported. The reaction is pseudo first order with respect to apoenzyme and the values of these pseudo first order rate constants are reported as a function of copper (II) concentration. Two copper ions bind to apoenzyme, and if the second one is rate limiting, the kinetically relevant copper concentration is the copper originally added minus the amount used in binding the first copper ion to enzyme. This modified copper concentration is linearly related to the magnitude of the pseudo first order rate constant, up to a copper concentration of 1.25 × 10−4 M (10-fold excess), giving a second order rate constant of 7.67 × 102 ± 0.93 × 102 M−1∙s−1.Key words: apotyrosinase, copper, tyrosinase.

Open-chain nitrogen compounds. Part XV. A kinetic study of the hydrolysis of 1-aryl-3-aryloxymethyl-3-methyltriazenes and related triazenes

1992 ◽  
Vol 70 (8) ◽  
pp. 2224-2233 ◽  
Author(s):  
Keith Vaughan ◽  
Donald L. Hooper ◽  
Marcus P. Merrin
Keyword(s):  
Rate Constant ◽  
Order Rate Constant ◽  
Buffer System ◽  
Open Chain ◽  
Nucleophilic Displacement ◽  
Ether Oxygen ◽  
Rate Of Hydrolysis ◽  
Electron Withdrawing Group ◽  
Ph Range ◽  
Kinetics Of

The kinetics of hydyrolysis of a series of 1-aryl-3-aryloxymethyl-3-methyltriazenes, Ar-N=N-NMe-CH2OAr′, was studied over the pH range 2–7.5. Reactions were followed by the change in UV absorbance spectra of the triazenes. The aryloxymethyltriazenes decompose more slowly at pH 7.5 than the hydroxymethyltriazenes, Ar-N=NMe-CH2OH; the hydrolysis is favoured by the presence of an electron-withdrawing group in Ar′. A mixed isopropanol/buffer system was developed in order to improve solubility of the aryloxymethyl triazenes. Lowering the pH caused an increase in the rate of hydrolysis and under strongly acidic conditions an electron-withdrawing group in Ar′ actually slows down the reaction. A Hammett plot of the pseudo-first-order rate constant, kobs, is curved, indicating that two or more mechanisms operate simultaneously and that the contribution of each mechanism is substituent-dependent. A plot of kobs vs. [buffer] is linear; the slope of the plot affords the rate constant, kb for the buffer-catalyzed reaction for each substituent. A Hammett plot of kb vs. σ is linear with ρ = +0.55, suggesting that the buffer-catalyzed reaction involves nucleophilic displacement of the phenoxy group by the buffer anion. Further analysis afforded the specific acid-catalyzed rate constants, [Formula: see text], for each substituent; this component of the reaction has a negative ρ, consistent with a mechanism involving protonation at the ether oxygen. The postulation that specific acid catalysis is a component of the reaction mechanism was confirmed by the observation of a solvent deuterium isotope effect, 2.28 > kH/kD > 1.60. Only the p-NO2 and p-CN phenyloxymethyltriazenes showed any spontaneous decomposition.

Sign in / Sign up

Export Citation Format

Share Document