scholarly journals Bond and topography evaluation of a Y-TZP ceramic with a superficial low-fusing porcelain glass layer after different hydrofluoric acid etching protocols

2018 ◽  
Vol 47 (6) ◽  
pp. 348-353
Author(s):  
Arthur Chaves SIMÕES ◽  
Jean Soares MIRANDA ◽  
Rodrigo Othávio de Assunção e SOUZA ◽  
Estevão Tomomitsu KIMPARA ◽  
Fabíola Pessôa Pereira LEITE
Keyword(s):  
Bond Strength ◽  
Hydrofluoric Acid ◽  
Statistical Tests ◽  
Adhesive Bond ◽  
Surface Treatments ◽  
Resin Cement ◽  
Acid Etching ◽  
Glass Layer ◽  
Ceramic Surface ◽  
Adhesive Failure

Abstract Introduction Despite being one of the most studied ceramics today, zirconia still does not have a well-defined adhesion protocol. Objective Evaluate the influence of different etching times and hydrofluoric acid (HF) concentrations on the zirconia surface and bond strength between a vitrified Y-TZP ceramic and a resin cement. Materials and method The zirconia surface treatments were: sandblasting with silica-coated alumina (Co); glaze application + 5% HF etching for 5s (G5-5s), 10s (G5-10s) or 20s (G5-20s); glaze application + 10% HF etching for 5s (G10-5s), 10 (G10-10s) or 20s (G10-20s) . Then, cement cylinders (3.3 × 3.3 mm) were built up for shear bond test on all specimens. The specimens were subjected to 6000 thermal cycling before the test. Fractures were analyzed by stereomicroscope. Data were statistically analyzed by Kruskal-Wallis and Dunn statistical tests (5%). Extra samples of each group were made to obtain profilometry and scanning electron microscopy (SEM). Result Zirconia-cement bond strength was affected by the ceramic surface treatments (p = 0.001). G10-5s (2.71 MPa) recorded the highest bond strength values, followed by the Co (2.05 MPa) while G5 groups had the lowest bond value. Adhesive failure of the samples predominated. The image analysis revealed G5 groups seem to have a lower roughness when compared to groups treated by 10% HF. The creation of pores in the low-fusing porcelain glass layer surface occurred only when 10% HF was used. Conclusion The low-fusing porcelain glass layer application was able to overcome the sandblasting and obtain a greater adhesive bond to the resinous cement, however, only when 10% HF was used for an interval of 5 seconds.

scholarly journals Low-Fusing Porcelain Glaze Application on 3Y-TZP Surfaces can Enhance Zirconia-Porcelain Adhesion

2016 ◽  
Vol 27 (5) ◽  
pp. 543-547 ◽  
Author(s):  
Lígia Tiaki Yamamoto ◽  
◽  
Vinícius Anéas Rodrigues ◽  
Lucio Strazzabosco Dornelles ◽  
Marco Antonio Bottino ◽  
...  
Keyword(s):  
Bond Strength ◽  
Hydrofluoric Acid ◽  
Shear Test ◽  
Silica Coating ◽  
Surface Treatments ◽  
Acid Etching ◽  
Control Group ◽  
Ceramic Surface ◽  
Adhesive Failure ◽  
Porcelain Glaze

Abstract The aim of this study was to assess whether surface treatment improves zirconia-porcelain adhesion. The 3Y-TZP blocks were cut into squares, then polished and sintered. The zirconia surface treatments were performed as follows: no treatment (C); tribochemical silica coating (TBS); glaze application + hydrofluoric acid etching (GA); glaze application + hydrofluoric acid etching + silanization (GAS); deposition of silica nanofilm (NF). After treatments, veneering porcelain cylinders (3.3 x 3.3 mm) were built up on all specimens and fired. Then the specimens were subjected to thermal cycling (6000 cycles), and subjected to shear test. Fractures were analyzed by stereomicroscopy and SEM. Data were statistically analyzed by 1-way ANOVA and Tukey's test (5%). Zirconia-porcelain bond strength was affected by the ceramic surface treatments (p=0.0001). GA (19.5±3 MPa) and GAS (16.2±4 MPa) recorded the highest bond strength values, while control group had the lowest bond value (10.1±4 MPa). Adhesive failure of the samples predominated. Therefore, glaze application as 3Y-TZP treatment before veneering porcelain stratification may enhance zirconia-porcelain adhesion.

The Effect of Aging and Surface treatments on Micro-shear Bond Strength of Resin Nano-Ceramic Material Using Two Resin Cements

2020 ◽  
Author(s):  
Ayman Mohammed Said
Keyword(s):  
Bond Strength ◽  
Hydrofluoric Acid ◽  
Shear Bond Strength ◽  
Surface Treatments ◽  
Resin Cement ◽  
Acid Etching ◽  
Resin Cements ◽  
Adhesive Resin ◽  
Mean Values ◽  
Adhesive Resin Cement

Purpose: To evaluate the effect of aging and different surface treatments on micro-shear bond strength of two resin cements to resin nano-ceramic composite blocks using an in-vitro study. Materials and methods: Blocks of resin nano-ceramic (Lava Ultimate, 3M, St Paul, Minnesota, USA) were used to prepare eight plates having the following dimensions: (14mm × 12mm × 2mm). After plates preparation they were assigned to two main groups according to the surface treatment applied, either hydrofluoric acid etching and silane or sandblasting and silane. Scanning electron microscope (SEM) was used to analyze the surface topography of the Lava-Ultimate plates before and after application of surface treatments. Two resin cements were used; dual cured adhesive resin cement (Bifix QM, VOCO, Cuxhafen, Germany) and dual cured self-adhesive resin cement (Bifix SE, VOCO, Cuxhafen, Germany) to create a five resin micro-cylinders received on each lava ultimate plate. Ten specimens from each subgroup were tested after 24 hours and the other ten specimens were tested after aging in saline for 6 months. Micro-shear bond strength test was applied until failure. . Multi-factorial ANOVA test and One-way ANOVA followed by pair-wise Tukey’s post-hoc tests were used to analyze the data. Results: Both resin cements showed statistically significant decrease on bond strength after aging. Before aging, both surface treatments with adhesive resin cement showed statistically significant higher micro-shear bond strength mean values than with self-adhesive resin cement. After aging sandblasting showed a statistically significant higher micro-shear bond strength mean values with adhesive resin cement, while hydrofluoric acid etching revealed a statistically non-significant higher values with adhesive resin cement than self-adhesive resin cement. Conclusion: For both surface treatments and resin cements aging had a detrimental effect on micro- shear bond strength.

scholarly journals The effect of surface treatment and thermocycling on the shear bond strength of porcelain laminate veneering material cemented with different luting cements

2019 ◽  
Vol 18 ◽  
pp. e191581
Author(s):  
Fawaz Alqahtani ◽  
Mohammed Alkhurays
Keyword(s):  
Bond Strength ◽  
Surface Treatment ◽  
Hydrofluoric Acid ◽  
Shear Bond Strength ◽  
Surface Treatments ◽  
Resin Cement ◽  
Ceramic Surface ◽  
Resin Cements ◽  
Significant Difference ◽  
Acid Etch

Aim: The study aimed to evaluate and compare the effect of different surface treatment and thermocycling on the shear bond strength (SBS) of different dual-/light-cure cements bonding porcelain laminate veneers (PLV). Methods: One hundred and twenty A2 shade lithium disilicate discs were divided into three groups based on the resin cement used and on the pretreatment received and then divided into two subgroups: thermocycling and control. The surface treatment were either micro-etched with aluminium trioxide and 10% hydrofluoric acid or etched with 10% hydrofluoric acid only before cementation. Three dual-cure (Variolink Esthetic (I), RelyX Ultimate (II), and RelyX Unicem (III)) and three light-cure (Variolink Veneer (IV), Variolink Esthetic (V), RelyX Veneer (VI)) resin cements were used for cementation. The SBS of the samples was evaluated and analysed using three -way ANOVA with statistical significant set at α=0.05. Results: For all resin cements tested with different surface treatments, there was a statistically significant difference within resin cements per surface treatment (p<0.05). The shear bond strength in the micro-etch group was significant higher than the acid-etch group (p<0.05) There was statistically significant interaction observed between the surface treatment and thermocycling (p<0.05) as well as the cement and thermocycling(p<0.05). It was observed that the reduction in shear bond strength after thermocycling was more pronounced in the acid etch subgroup as compared to the microetch subgroup. However, the interaction between the three factors: surface treatments, thermocycling and resin cements did not demonstrate statistically significant differences between and within groups (p=0.087). Conclusions: Within the limitations of the present study, it acan be concluded that Dual cure resin cements showed a higher Shear bond strength as compared to light cure resin cements. Thermal cycling significantly decreased the shear bond strength for both ceramic surface treatments. After thermocycling, the specimens with 10% HF surface treatment showed lower shear bond strength values when compared to those treated by sandblasting with Al2O3 particles.

Effects of Surface Treatments, Thermocycling, and Cyclic Loading on the Bond Strength of a Resin Cement Bonded to a Lithium Disilicate Glass Ceramic

2013 ◽  
Vol 38 (2) ◽  
pp. 208-217 ◽  
Author(s):  
GB Guarda ◽  
AB Correr ◽  
LS Gonçalves ◽  
AR Costa ◽  
GA Borges ◽  
...  
Keyword(s):  
Bond Strength ◽  
Glass Ceramic ◽  
Hydrofluoric Acid ◽  
Lithium Disilicate ◽  
Surface Treatments ◽  
Resin Cement ◽  
Control Group ◽  
Ceramic Surface ◽  
Microtensile Bond Strength ◽  
Ceramic Blocks

SUMMARY Objectives The aim of this present study was to investigate the effect of two surface treatments, fatigue and thermocycling, on the microtensile bond strength of a newly introduced lithium disilicate glass ceramic (IPS e.max Press, Ivoclar Vivadent) and a dual-cured resin cement. Methods A total of 18 ceramic blocks (10 mm long × 7 mm wide × 3.0 mm thick) were fabricated and divided into six groups (n=3): groups 1, 2, and 3—air particle abraded for five seconds with 50-μm aluminum oxide particles; groups 4, 5, and 6—acid etched with 10% hydrofluoric acid for 20 seconds. A silane coupling agent was applied onto all specimens and allowed to dry for five seconds, and the ceramic blocks were bonded to a block of composite Tetric N-Ceram (Ivoclar Vivadent) with RelyX ARC (3M ESPE) resin cement and placed under a 500-g static load for two minutes. The cement excess was removed with a disposable microbrush, and four periods of light activation for 40 seconds each were performed at right angles using an LED curing unit (UltraLume LED 5, Ultradent) with a final 40 second light exposure from the top surface. All of the specimens were stored in distilled water at 37°C for 24 hours. Groups 2 and 5 were submitted to 3,000 thermal cycles between 5°C and 55°C, and groups 3 and 6 were submitted to a fatigue test of 100,000 cycles at 2 Hz. Specimens were sectioned perpendicular to the bonding area to obtain beams with a cross-sectional area of 1 mm2 (30 beams per group) and submitted to a microtensile bond strength test in a testing machine (EZ Test) at a crosshead speed of 0.5 mm/min. Data were submitted to analysis of variance and Tukey post hoc test (p≤0.05). Results The microtensile bond strength values (MPa) were 26.9 ± 6.9, 22.2 ± 7.8, and 21.2 ± 9.1 for groups 1–3 and 35.0 ± 9.6, 24.3 ± 8.9, and 23.9 ± 6.3 for groups 4–6. For the control group, fatigue testing and thermocycling produced a predominance of adhesive failures. Fatigue and thermocycling significantly decreased the microtensile bond strength for both ceramic surface treatments when compared with the control groups. Etching with 10% hydrofluoric acid significantly increased the microtensile bond strength for the control group.

scholarly journals Four chemical methods of porcelain conditioning and their influence over bond strength and surface integrity

2015 ◽  
Vol 20 (4) ◽  
pp. 51-56 ◽  
Author(s):  
João Paulo Fragomeni Stella ◽  
Andrea Becker Oliveira ◽  
Lincoln Issamu Nojima ◽  
Mariana Marquezan
Keyword(s):  
Phosphoric Acid ◽  
Bond Strength ◽  
Surface Integrity ◽  
Hydrofluoric Acid ◽  
Shear Bond Strength ◽  
Testing Machine ◽  
Acid Etching ◽  
Ceramic Surface ◽  
Surface Conditioning ◽  
Phosphoric Acid Etching

OBJECTIVE: To assess four different chemical surface conditioning methods for ceramic material before bracket bonding, and their impact on shear bond strength and surface integrity at debonding.METHODS: Four experimental groups (n = 13) were set up according to the ceramic conditioning method: G1 = 37% phosphoric acid etching followed by silane application; G2 = 37% liquid phosphoric acid etching, no rinsing, followed by silane application; G3 = 10% hydrofluoric acid etching alone; and G4 = 10% hydrofluoric acid etching followed by silane application. After surface conditioning, metal brackets were bonded to porcelain by means of the Transbond XP system (3M Unitek). Samples were submitted to shear bond strength tests in a universal testing machine and the surfaces were later assessed with a microscope under 8 X magnification. ANOVA/Tukey tests were performed to establish the difference between groups (α= 5%).RESULTS: The highest shear bond strength values were found in groups G3 and G4 (22.01 ± 2.15 MPa and 22.83 ± 3.32 Mpa, respectively), followed by G1 (16.42 ± 3.61 MPa) and G2 (9.29 ± 1.95 MPa). As regards surface evaluation after bracket debonding, the use of liquid phosphoric acid followed by silane application (G2) produced the least damage to porcelain. When hydrofluoric acid and silane were applied, the risk of ceramic fracture increased.CONCLUSIONS: Acceptable levels of bond strength for clinical use were reached by all methods tested; however, liquid phosphoric acid etching followed by silane application (G2) resulted in the least damage to the ceramic surface.

scholarly journals Effect of surface treatments of laboratory-fabricated composites on the microtensile bond strength to a luting resin cement

2004 ◽  
Vol 12 (1) ◽  
pp. 45-50 ◽  
Author(s):  
Carlos José Soares ◽  
Marcelo Giannini ◽  
Marcelo Tavares de Oliveira ◽  
Luis Alexandre Maffei Sartini Paulillo ◽  
Luis Roberto Marcondes Martins
Keyword(s):  
Bond Strength ◽  
Hydrofluoric Acid ◽  
Composite Resin ◽  
Surface Treatments ◽  
Resin Cement ◽  
Single Bond ◽  
Microtensile Bond Strength ◽  
Bonded Interface ◽  
Luting Composite ◽  
Effect Of Surface

The purpose of this study was to evaluate the influence of different surface treatments on composite resin on the microtensile bond strength to a luting resin cement. Two laboratory composites for indirect restorations, Solidex and Targis, and a conventional composite, Filtek Z250, were tested. Forty-eight composite resin blocks (5.0 x 5.0 x 5.0mm) were incrementally manufactured, which were randomly divided into six groups, according to the surface treatments: 1- control, 600-grit SiC paper (C); 2- silane priming (SI); 3- sandblasting with 50 mm Al2O3 for 10s (SA); 4- etching with 10% hydrofluoric acid for 60 s (HF); 5- HF + SI; 6 - SA + SI. Composite blocks submitted to similar surface treatments were bonded together with the resin adhesive Single Bond and Rely X luting composite. A 500-g load was applied for 5 minutes and the samples were light-cured for 40s. The bonded blocks were serially sectioned into 3 slabs with 0.9mm of thickness perpendicularly to the bonded interface (n = 12). Slabs were trimmed to a dumbbell shape and tested in tension at 0.5mm/min. For all composites tested, the application of a silane primer after sandblasting provided the highest bond strength means.

scholarly journals Silane Heat Treatment Could Eliminate the Hydrofluoric Acid Etching of Lithium Disilicate Overlays: A Four-Year Follow-Up

2021 ◽  
Vol 2021 ◽  
pp. 1-7
Author(s):  
Spartak Spasov Yanakiev ◽  
Mirela Borislavova Marinova-Takorova
Keyword(s):  
Heat Treatment ◽  
Bond Strength ◽  
Hydrofluoric Acid ◽  
Lithium Disilicate ◽  
Acid Etching ◽  
Preparation Technique ◽  
Ceramic Surface ◽  
Dental Adhesive ◽  
Ceramic Bond

A four-year follow-up of a novel silane heat treatment method for bonding lithium disilicate overlays to tooth structures without hydrofluoric acid etching of the ceramic surface is presented in this case report. Silane heat treatment modifies the silane layer and thus enhances resin ceramic bond strength without hydrofluoric acid etching. The standard ceramic preparation technique prior to bonding silicate ceramics to tooth structure is hydrofluoric acid etching and applying a silane coupling agent, followed by dental adhesive. In this case, the micromechanical roughening of the ceramic surface was performed by air abrasion with Al2O3. Silane heat treatment with constant 120°C airflow, applied for 60 sec, followed by dental adhesive application enhanced the resin-ceramic bond strength. After a four-year follow-up, the restorations’ clinical appearance could be defined as excellent/very good according to the FDI clinical criteria for the evaluation of direct and indirect restorations. This clinical result supports many in vitro studies regarding the resin-ceramic bond strength and durability obtained through postsilanization heat treatment.

scholarly journals Effect of surface treatment on the shear bond strength of a resin-based cement to porcelain

2006 ◽  
Vol 17 (4) ◽  
pp. 290-295 ◽  
Author(s):  
Marcos Paulo Nagayassu ◽  
Luciana Keiko Shintome ◽  
Eduardo Shigueyuki Uemura ◽  
José Eduardo Junho de Araújo
Keyword(s):  
Bond Strength ◽  
Surface Treatment ◽  
Hydrofluoric Acid ◽  
Shear Bond Strength ◽  
In Vitro Study ◽  
Resin Cement ◽  
Vitro Study ◽  
Acid Etching ◽  
And Control

The purpose of this in vitro study was to evaluate the effect of different surface treatments on the shear bond strength of a resin-based cement to porcelain. Sixty pairs of 50% aluminous porcelain discs were fabricated. In each pair, one disc measured 6 mm in diameter X 3 mm thickness (A) and the other measured 3 mm in diameter X 3mm thickness (B). The specimens were randomly assigned to 6 groups (n=10 pairs of discs), according to the surface treatment: etching with 10% hydrofluoric acid for 2 or 4min (G1 and G2); 50-µm particle aluminum oxide sandblasting for 5 s (G3); sandblasting followed by etching for 2 or 4min (G4 and G5) and control - no treatment (G6). A silane agent was applied to the treated surface of both discs of each pair. Bistite II DC dual-cure resin cement was applied and the B discs were bonded to their respective A discs. Specimens were stored in distilled water at 37ºC for 24 h and were tested in shear strength at a crosshead speed of 2 mm/min. Means in MPa were: G1: 14.21 ± 4.68; G2: 8.92 ± 3.02; G3: 10.04 ± 2.37; G4: 12.74 ± 5.15; G5: 10.99 ± 3.35; G6: 6.09 ± 1.84. Data were compared by one-way ANOVA and Tukey's test at 5% significance level. Bond strength recorded after 2-min acid etching was significantly higher than 4-min etching (p<0.05) and control (p<0.05), but did not differ significantlyfrom sandblasting alone (p>0.05) or followed by etching for 2 or 4 min (p>0.05). Within the limitations of an in vitro study, it may be concluded that 2-min hydrofluoric acid etching produced a favorable micromechanical retention that enhanced resin cement bond strength to porcelain.

scholarly journals Effect of Acid Etching, Silane and Thermal Cycling on the Bond Strength of Metallic Brackets to Ceramic

2016 ◽  
Vol 27 (6) ◽  
pp. 734-738 ◽  
Author(s):  
Natália Regina Santos de Matos ◽  
Ana Rosa Costa ◽  
Heloísa Cristina Valdrighi ◽  
Américo Bortolazzo Correr ◽  
Silvia Amélia Vedovello ◽  
...  
Keyword(s):  
Bond Strength ◽  
Thermal Cycling ◽  
Surface Treatment ◽  
Hydrofluoric Acid ◽  
Shear Bond Strength ◽  
Deionized Water ◽  
Acid Etching ◽  
Ceramic Surface ◽  
Adhesive Remnant Index ◽  
Post Hoc

Abstract The aim of this study was to evaluate the effect of silanes, thermal cycling and acid etching on the shear bond strength (SBS) of metallic brackets to feldspathic ceramic. Feldspathic ceramic cylinders (Groups 1, 2, 5 and 6) were etched for 60 s with 10% hydrofluoric acid and Groups 3, 4, 7 and 8, without acid etching. Two layers of silane Clearfil Ceramic Primer (CCP, Groups 1 to 4) and two layers of RelyX Ceramic Primer (RCP, groups 5 to 8) were applied and dried for 60 s. Brackets were bonded to the cylinders with Transbond XT and light-activated for 40 s with Bluephase G2. All specimens were stored in deionized water at 37 °C for 24 h, and the specimens of groups 1, 3, 5 and 7 were submitted to 7,000 thermal cycles (5 °C/55 °C). After storage, the SBS test was performed at a crosshead speed of 1 mm/min. Data were subjected to three-way ANOVA and Tukey's post hoc test (α=0.05). The adhesive remnant index (ARI) was evaluated at 8x magnification. The SBS of CCP was significantly greater than of RCP (p<0.05), with or without thermal cycling. Thermal cycling significantly reduced the SBS (p<0.05). The groups submitted to acid etching showed significantly higher SBS than those without acid etching (p<0.05). In conclusion, thermal cycling reduced SBS for all groups. The best ceramic surface treatment for bracket bonding was achieved by acid etching and CCP silane. The ARI results showed predominance of score 0 for all groups.

scholarly journals Effect of Ceramic Etching Protocols on Resin Bond Strength to a Feldspar Ceramic

2015 ◽  
Vol 40 (2) ◽  
pp. E40-E46 ◽  
Author(s):  
MA Bottino ◽  
A Snellaert ◽  
CD Bergoli ◽  
M Özcan ◽  
MC Bottino ◽  
...  
Keyword(s):  
Bond Strength ◽  
Resin Cement ◽  
Acid Etching ◽  
Ceramic Surface ◽  
Mean Values ◽  
Force Microscopy ◽  
Ceramic Surfaces ◽  
Aging Conditions ◽  
Ceramic Blocks ◽  
Microtensile Test

SUMMARY This study sought to evaluate the resin microtensile bond strength (MTBS) stability of a leucite-reinforced ceramic after different ceramic etching protocols. The microtensile test had 40 ceramic blocks (5×5×6 mm) assigned to five groups (n=8), in accordance with the following surface etching protocols: NE nonetched (control); 9HF: hydrofluoric (HF) acid etching (9%HF)+wash/dry; 4HF: 4%HF+wash/dry; 5HF: 5%HF+wash/dry; and 5HF+N: 5%HF+neutralizer+wash/dry+ultrasonic-cleaning. Etched ceramic surfaces were treated with a silane agent. Next, resin cement blocks were built on the prepared ceramic surface and stored for 24 hours in distilled water at 37°C. The specimens were then sectioned to obtain microtensile beams (32/block), which were randomly assigned to the following conditions, nonaged (immediate test) and aged (water storage for 150 days plus 12,000 thermal cycles), before the microtensile test. Bond strength data were submitted to one-way analysis of variance and Tukey test (α=0.05). Additional ceramic samples were subjected to the different ceramic etching protocols and evaluated using a scanning electron microscope (n=2) and atomic force microscopy (n=2). Aging led to a statistically significant decrease in the MTBS for all groups, except the untreated one (NE). Among the groups submitted to the same aging conditions, the untreated (NE) revealed inferior MTBS values compared to the 9HF and 4HF groups. The 5HF and 5HF+N groups had intermediate mean values, being statistically similar to the higher values presented by the 9HF and 4HF groups and to the lower value associated with the NE group. The neutralization procedure did not enhance the ceramic/resin cement bond strength. HF acid etching is a crucial step in resin/ceramic bonding.

Sign in / Sign up

Export Citation Format

Share Document