scholarly journals Excessive coverage effect (over peening) in the blasting operation of aluminum alloy “AA 7475-T7351” with steel shot

2020 ◽  
Vol 25 (2) ◽  
Author(s):  
José Aparecido Granato ◽  
João Antonio Pontes ◽  
Erika Peterson Gonçalves ◽  
Viliam Sinka
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloy ◽  
Fatigue Life ◽  
Residual Stresses ◽  
Shot Peening ◽  
Fatigue Tests ◽  
Cold Surface ◽  
Blasting Operation ◽  
Cause Of Failure ◽  
Metal Materials

ABSTRACT Aluminum and its alloys are widely used in the aeronautics industry due to its high lightness and ductility, and it can add other elements, thus changing its characteristics. Fatigue is the major cause of failure of metal materials due to the dynamic and oscillating stresses of the finished materials. The objective of this work is to evaluate the effect of Shot Peening with coverage percentages 1blasting, 3 blasting and 10 blasting in fatigue life of aluminum alloy AA 7475-T351. Shot Peening is a cold surface treatment used to increase fatigue life of the alloy by inducing residual stresses of compression on the surface of the part. In the Shot Peening process, spherical steel grids of type S230 were used, in which the specimens were subjected to 1blasting, 3 blasting and 10 blasting coverage in two stress levels (42 Ksi and 50 Ksi). The results presented in the fatigue tests and electron scanning (SEM) showed the increase in the mechanical properties of all the samples, and those exposed to 1 blasting and 3 blasting presented better results.

scholarly journals Fretting-Fatigue Analysis of Shot-Peened Al 7075-T651 Test Specimens

Metals ◽  
2019 ◽  
Vol 9 (5) ◽  
pp. 586 ◽  
Author(s):  
Vicente Martín ◽  
Jesús Vázquez ◽  
Carlos Navarro ◽  
Jaime Domínguez
Keyword(s):  
Fatigue Life ◽  
Residual Stresses ◽  
Shot Peening ◽  
Normal Load ◽  
Fretting Fatigue ◽  
Fatigue Tests ◽  
Material Surface ◽  
Tangential Load ◽  
Bulk Stress ◽  
Al 7075

Shot peening is a mechanical treatment that induces several changes in the material: surface roughness, increased hardness close to the surface, and, the most important, compressive residual stresses. This paper analyzes the effect of this treatment on alloy Al 7075-T651 in the case of fretting fatigue with cylindrical contact through the results of 114 fretting fatigue tests. There are three independent loads applied in this type of test: a constant normal load N, pressing the contact pad against the specimen; a cyclic bulk stress σ in the specimen; and a cyclic tangential load Q through the contact. Four specimens at each of 23 different combinations of these three parameters were tested—two specimens without any treatment and two treated with shot peening. The fatigue lives, contact surface, fracture surface, and residual stresses and hardness were studied. Improvement in fatigue life ranged from 3 to 22, depending on fatigue life. The relaxation of residual-stress distribution related to the number of applied cycles was also measured. Finally, another group of specimens treated with shot peening was polished and tested, obtaining similar lives as in the tests with specimens that were shot-peened but not polished.

scholarly journals The Effect of Laser Peening without Coating on the Fatigue of a 6082-T6 Aluminum Alloy with a Curved Notch

Metals ◽  
2019 ◽  
Vol 9 (7) ◽  
pp. 728 ◽  
Author(s):  
Enrico Troiani ◽  
Nicola Zavatta
Keyword(s):  
Aluminum Alloy ◽  
Fatigue Life ◽  
Residual Stresses ◽  
Fatigue Behavior ◽  
Surface Hardness ◽  
Element Model ◽  
Fatigue Tests ◽  
Fatigue Properties ◽  
Laser Peening ◽  
Laser Peening Without Coating

Laser shock peening has established itself as an effective surface treatment to enhance the fatigue properties of metallic materials. Although a number of works have dealt with the formation of residual stresses, and their consequent effects on the fatigue behavior, the influence of material geometry on the peening process has not been widely addressed. In this paper, Laser Peening without Coating (LPwC) is applied at the surface of a notch in specimens made of a 6082-T6 aluminum alloy. The treated specimens are tested by three-point bending fatigue tests, and their fatigue life is compared to that of untreated samples with an identical geometry. The fatigue life of the treated specimens is found to be 1.7 to 3.3 times longer. Brinell hardness measurements evidence an increase in the surface hardness of about 50%, following the treatment. The material response to peening is modelled by a finite element model, and the compressive residual stresses are computed accordingly. Stresses as high as −210 MPa are present at the notch. The ratio between the notch curvature and the laser spot radius is proposed as a parameter to evaluate the influence of the notch.

scholarly journals Influence of Shot Peening on the Isothermal Fatigue Behavior of the Gamma Titanium Aluminide Ti-48Al-2Cr-2Nb at 750 °C

Metals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1083
Author(s):  
Christoph Breuner ◽  
Stefan Guth ◽  
Elias Gall ◽  
Radosław Swadźba ◽  
Jens Gibmeier ◽  
...  
Keyword(s):  
Residual Stresses ◽  
Shot Peening ◽  
Elevated Temperatures ◽  
Stress Amplitude ◽  
Negative Impact ◽  
Fatigue Behavior ◽  
Surface Hardness ◽  
Fatigue Tests ◽  
Positive Effects ◽  
Isothermal Fatigue

One possibility to improve the fatigue life and strength of metallic materials is shot peening. However, at elevated temperatures, the induced residual stresses may relax. To investigate the influence of shot peening on high-temperature fatigue behavior, isothermal fatigue tests were conducted on shot-peened and untreated samples of gamma TiAl 48-2-2 at 750 °C in air. The shot-peened material was characterized using EBSD, microhardness, and residual stress analyses. Shot peening leads to a significant increase in surface hardness and high compressive residual stresses near the surface. Both effects may have a positive influence on lifetime. However, it also leads to surface notches and tensile residual stresses in the bulk material with a negative impact on cyclic lifetime. During fully reversed uniaxial tension-compression fatigue tests (R = −1) at a stress amplitude of 260 MPa, the positive effects dominate, and the fatigue lifetime increases. At a lower stress amplitude of 230 MPa, the negative effect of internal tensile residual stresses dominates, and the lifetime decreases. Shot peening leads to a transition from surface to volume crack initiation if the surface is not damaged by the shots.

Fatigue Life Improvement of Welded Elements and Structures by Ultrasonic Impact Treatment

2011 ◽  
Author(s):  
Yuriy Kudryavtsev ◽  
Jacob Kleiman
Keyword(s):  
Mechanical Properties ◽  
Fatigue Life ◽  
Fatigue Strength ◽  
Residual Stresses ◽  
Fatigue Testing ◽  
Highway Bridges ◽  
Surface Layers ◽  
Ultrasonic Impact Treatment ◽  
Stress Relieving ◽  
Life Improvement

The ultrasonic impact treatment (UIT) is relatively new and promising process for fatigue life improvement of welded elements and structures. In most industrial applications this process is known as ultrasonic peening (UP). The beneficial effect of UIT/UP is achieved mainly by relieving of harmful tensile residual stresses and introducing of compressive residual stresses into surface layers of a material, decreasing of stress concentration in weld toe zones and enhancement of mechanical properties of the surface layers of the material. The UP technique is based on the combined effect of high frequency impacts of special strikers and ultrasonic oscillations in treated material. Fatigue testing of welded specimens showed that UP is the most efficient improvement treatment as compared with traditional techniques such as grinding, TIG-dressing, heat treatment, hammer peening and application of LTT electrodes. The developed computerized complex for UP was successfully applied for increasing the fatigue life and corrosion resistance of welded elements, elimination of distortions caused by welding and other technological processes, residual stress relieving, increasing of the hardness of the surface of materials. The UP could be effectively applied for fatigue life improvement during manufacturing, rehabilitation and repair of welded elements and structures. The areas/industries where the UP process was applied successfully include: Shipbuilding, Railway and Highway Bridges, Construction Equipment, Mining, Automotive, Aerospace. The results of fatigue testing of welded elements in as-welded condition and after application of UP are considered in this paper. It is shown that UP is the most effective and economic technique for increasing of fatigue strength of welded elements in materials of different strength. These results also show a strong tendency of increasing of fatigue strength of welded elements after application of UP with the increase in mechanical properties of the material used.

scholarly journals Changing in Fatigue Life of 300 M Bainitic Steel After Laser Carburizing and Plasma Nitriding

2018 ◽  
Vol 165 ◽  
pp. 21002 ◽  
Author(s):  
Antonio J. Abdalla ◽  
Douglas Santos ◽  
Getúlio Vasconcelos ◽  
Vladimir H. Baggio-Scheid ◽  
Deivid F. Silva
Keyword(s):  
Mechanical Properties ◽  
Fatigue Life ◽  
Plasma Nitriding ◽  
Fatigue Behavior ◽  
High Strength ◽  
Tensile Tests ◽  
Steel Sample ◽  
Fatigue Tests ◽  
300M Steel ◽  
Structural Applications

In this work 300M steel samples is used. This high-strength steel is used in aeronautic and aerospace industry and other structural applications. Initially the 300 M steel sample was submitted to a heat treatment to obtain a bainític structure. It was heated at 850 °C for 30 minutes and after that, cooled at 300 °C for 60 minutes. Afterwards two types of surface treatments have been employed: (a) using low-power laser CO2 (125 W) for introducing carbon into the surface and (b) plasma nitriding at a temperature of 500° C for 3 hours. After surface treatment, the metallographic preparation was carried out and the observations with optical and electronic microscopy have been made. The analysis of the coating showed an increase in the hardness of layer formed on the surface, mainly, among the nitriding layers. The mechanical properties were analyzed using tensile and fatigue tests. The results showed that the mechanical properties in tensile tests were strongly affected by the bainitic microstructure. The steel that received the nitriding surface by plasma treatment showed better fatigue behavior. The results are very promising because the layer formed on steel surface, in addition to improving the fatigue life, still improves protection against corrosion and wear.

scholarly journals Effects of Actual Marine Atmospheric Pre-Corrosion and Pre-Fatigue on the Fatigue Property of 7085 Aluminum Alloy

Metals ◽  
2022 ◽  
Vol 12 (1) ◽  
pp. 81
Author(s):  
Laixin Shi ◽  
Lin Xiang ◽  
Jianquan Tao ◽  
Jun Liu ◽  
Qiang Chen ◽  
...  
Keyword(s):  
Aluminum Alloy ◽  
Fatigue Life ◽  
Pitting Corrosion ◽  
Atmospheric Corrosion ◽  
Fatigue Property ◽  
Outdoor Exposure ◽  
Fatigue Tests ◽  
Constant Amplitude ◽  
Fatigue Fractography ◽  
Corrosion Mode

Effects of actual marine atmospheric precorrosion and prefatigue on the fatigue property of 7085-T7452 aluminum alloy were investigated by using the methods of marine atmospheric outdoor exposure tests and constant amplitude axial fatigue tests. Marine atmospheric corrosion morphologies, fatigue life, and fatigue fractography were analyzed. After three months of outdoor exposure, both pitting corrosion and intergranular corrosion (IGC) occurred, while the latter was the dominant marine atmospheric corrosion mode. Marine atmospheric precorrosion could result in a dramatical decrease in the fatigue life of the as-received 7085-T7452 aluminum alloy, while selective prefatigue can improve the total fatigue life of the precorroded specimen. The mechanism of the actual marine atmospheric corrosion and its effects on the fatigue life of the 7085-T7452 aluminum alloy were also discussed.

The Effects of Periodic High Loads on Fretting Fatigue

1981 ◽  
Vol 103 (3) ◽  
pp. 223-228 ◽  
Author(s):  
A. Kantimathi ◽  
J. A. Alic
Keyword(s):  
Aluminum Alloy ◽  
Fatigue Life ◽  
Growth Retardation ◽  
Fretting Fatigue ◽  
Fatigue Tests ◽  
Constant Amplitude ◽  
Axial Loads ◽  
Prolonged Fatigue ◽  
Stress Ratios ◽  
Crack Growth Retardation

Fretting fatigue tests have been conducted on 7075-T7351 aluminum alloy coupons with fretting pads of the same material. Three different stress ratios were used, the otherwise constant amplitude axial loads being interrupted every 1000 cycles by either tensile overloads to 400 MPa or compressive underloads to −200 MPa. Tensile overloads greatly prolonged fatigue life for low stresses where the overload ratios were 1.6 and above; compressive underloads had comparatively little effect. The results are discussed in terms of crack growth retardation phenomena.

Sign in / Sign up

Export Citation Format

Share Document