STATIC AND DYNAMIC TESTS ON A MODEL SHEAR WALL STRUCTURE.

1972 ◽  
Vol 51 (4) ◽  
pp. 701-710
Author(s):  
AW IRWIN ◽  
Keyword(s):  
Shear Wall ◽  
Wall Structure ◽  
Dynamic Tests ◽  
Static And Dynamic Tests

DISCUSSION. STATIC AND DYNAMIC TESTS ON A SHEAR WALL STRUCTURE.

1972 ◽  
Vol 53 (3) ◽  
pp. 659-660
Author(s):  
AW IRWIN ◽  
WK TSO
Keyword(s):  
Shear Wall ◽  
Wall Structure ◽  
Dynamic Tests ◽  
Static And Dynamic Tests

Study on Rational Ratios of Lateral Stiffness for Masonry Building with Frame Structure at First Two Stories

2012 ◽  
Vol 174-177 ◽  
pp. 2012-2015
Author(s):  
Xiao Long Zhou ◽  
Ying Min Li ◽  
Lin Bo Song ◽  
Qian Tan
Keyword(s):  
Seismic Performance ◽  
Time History ◽  
Shear Wall ◽  
Calculation Model ◽  
Frame Structure ◽  
Wall Structure ◽  
Masonry Building ◽  
Lateral Stiffness ◽  
Stiffness Ratio ◽  
Lateral Stiffness Ratio

There are two typical seismic damage characteristics to the masonry building with frame shear wall structure at first two stories, and the lateral stiffness ratio of the third storey to the second storey is one of the key factors mostly affecting the seismic performance of this kind of building. However, some factors are not considered sufficiently in current Chinese seismic codes. According to the theory of performance-based seismic design, the seismic performance of this kind of structure is analyzed in this paper by taking time-history analysis on models which with different storey stiffness ratios. The results show that when the lateral stiffness ratio controlled in a reasonable range, the upper masonry deformation can be ensured in a range of elastic roughly, and the bottom frame can be guaranteed to have sufficient deformation and energy dissipation capacity. Finally, according to the seismic performance characteristics of masonry building with frame shear wall structure at first two stories, especially the characteristics under strong earthquakes, a method of simplified calculation model for the upper masonry is discussed in this paper.

The effect of the indenter elasticity on the Hertzian fracture of brittle materials

1973 ◽  
Vol 334 (1596) ◽  
pp. 95-117 ◽  
Keyword(s):  
Fracture Stress ◽  
Opposite Effect ◽  
Test Material ◽  
Test Surface ◽  
Dynamic Tests ◽  
Frictional Forces ◽  
Consistent Increase ◽  
Static And Dynamic Tests ◽  
Ring Crack ◽  
Ring Cracks

A spherical indenter loaded statically or dynamically into contact with the surface of a brittle material produces a well-defined ring crack. This phenomenon, when interpreted by the Hertz theory of elastic contact, provides a convenient test for the strength of the material. If the elastic modulus of the indenter is different from that of the test material, e. g. a steel indenter in contact with a glass surface, frictional forces are brought into play at the interface which modify the Hertz distribution of contact stress. This effect has been examined both theo­retically and experimentally. An indenter which is more rigid than the test surface is shown to lead to an apparent increase in fracture strength of the material, a less rigid indenter has the opposite effect. Static and dynamic tests of plate glass showed a consistent increase in apparent fracture stress of about 50 % using spherical steel indenters compared with glass indenters. This increase agrees well with the influence of friction upon the Hertzian stress calculated theoretically. The average radius of the ring cracks produced by steel indenters was observed to be greater than that produced by glass indenters, an effect of friction also predicted by the theory. Secondary ring cracks of smaller radius have frequently been observed during unloading of a steel indenter. These were not found when a glass indenter was used and an explanation is suggested in terms of the frictional effect which arises from a difference in elasticity between the indenter and the test surface.

Evaluation Method of U-Bolt Energy Absorption

2009 ◽  
Author(s):  
Eiji Shirai ◽  
Tetsuya Zaitsu ◽  
Kazutoyo Ikeda ◽  
Toshiaki Yoshii ◽  
Masami Kondo ◽  
...  
Keyword(s):  
Energy Absorption ◽  
Evaluation Method ◽  
Design Procedure ◽  
Piping System ◽  
Design Technique ◽  
Dynamic Tests ◽  
Key Issues ◽  
Static And Dynamic Tests ◽  
Force Displacement ◽  
Rigid Design

At domestic PWR plants in Japan, one of the major key issues is earthquake-proof safety [1–3]. Recently, a design procedure using energy absorption, not conventional rigid design, was authorized according to revised review guidelines for aseismic design (JEAC4601). Therefore, we focused on the design technique that utilizes energy absorption effects to reduce the seismic responses of the piping system with U-Bolt, by the static and dynamic tests of simplified piping model supported by U-Bolt. The force-displacement characteristics and a fatigue diagram were obtained by the tests.

Inspection and Model Experiment of a Damaged Arch Bridge

2007 ◽  
Vol 340-341 ◽  
pp. 223-228
Author(s):  
Ying Fang Fan ◽  
Zhi Qiang Hu ◽  
Jing Zhou
Keyword(s):  
Model Experiment ◽  
Dynamic Test ◽  
Dynamic Responses ◽  
Dynamic Tests ◽  
Arch Bridge ◽  
Mechanical Responses ◽  
Organic Glasses ◽  
Bridge Model ◽  
Static And Dynamic Tests ◽  
Good Agreement

The structural behavior of an old six-span reinforced concrete arch bridge, which has been in service for about 40 years, is investigated. Field monitoring (inclusive of test of material property, static and dynamic test of the bridge) was conducted, static and dynamic responses of the bridge are obtained. Based on the primitive bridge, a scaled one-span bridge model was fabricated by organic-glasses. Both the static and dynamic tests were executed on the bridge model in the laboratory. Since the arch rib is the crucial member for the arch bridge, 7 notches were cut on both arch ribs of the bridge model to simulate different damages of the arch rib. Mechanical responses of the bridge with different damages on the arch ribs were achieved. FEM analyses were preformed on the bridge as well. Numerical results show good agreement with the experimental results.

Study on the shear wall structure with combined form of replaceable devices

2017 ◽  
Vol 21 (9) ◽  
pp. 1327-1348
Author(s):  
Cong Chen ◽  
Renjie Xiao ◽  
Xilin Lu ◽  
Yun Chen
Keyword(s):  
Shear Walls ◽  
Shear Wall ◽  
Performance Comparison ◽  
Wall Structure ◽  
Structural Part ◽  
Coupled Shear Wall ◽  
Wall Structures ◽  
Strength And Stiffness ◽  
Energy Dissipated ◽  
Resilient Structure

Structure with replaceable devices is a type of earthquake resilient structure developed to restore the structure immediately after strong earthquakes. Current researches focus on one type of the replaceable device located in the structural part that is most likely to be damaged; however, plastic deformation would not be limited in a specific part but expand to other parts. To concentrate possible damage in shear wall structures, combined form of replaceable devices was introduced in this article. Based on previous studies, combined form of replaceable coupling beam and replaceable wall foot was used in a coupled shear wall. Influences of the dimension and location of the replaceable devices to the strength and stiffness of the shear wall were investigated through numerical modeling, which was verified by experimental data. Performance comparison between the shear walls with one type and combined form of replaceable devices and the conventional coupled shear wall was performed. In general, the shear wall with combined form of replaceable devices is shown to be better energy dissipated, and proper dimensions and locations of the replaceable devices should be determined.

Sign in / Sign up

Export Citation Format

Share Document