scholarly journals Amino-dealkoxylation of hm citruc pectin with n-alkylamines: a kinetic study

2004 ◽  
Vol 22 (SI - Chem. Reactions in Foods V) ◽  
pp. S235-2S37
Author(s):  
L. Sihelniková ◽  
A. Synytsya ◽  
J. Čopíková
Keyword(s):  
Reaction Time ◽  
Food Industry ◽  
Heterogeneous Reaction ◽  
Primary Amines ◽  
Reaction Yield ◽  
Citrus Pectin ◽  
Reaction Conditions ◽  
Plant Polysaccharides ◽  
Gelling Properties ◽  
The Common

Pectins are plant polysaccharides that are widely used in food industry. Chemical modification of pectins influences their technological properties. Amidated pectins are important pectin derivatives with good gelling properties at low-sugar conditions. The common method of pectin amidation is ammonolysis of methyl ester groups of highly methoxylated (HM) pectins in heterogeneous reaction with ammonia in methanol. Aminodealkoxylation (aminolysis) of HM pectin with primary amines leads to the formation of N-alkylpectinamides. The reaction yield of aminolysis depends on reaction time, temperature and the pectin/alkylamine ratio. The reaction of HM citrus pectin (type XSS, Danisco) with five chosen n-alkylamines (n-butylamine, n-hexylamine, n-octylamine, n-dodecylamine and n-octadecylamine) was carried out in N,N-dimethylformamide at 20°C (n-butylamine, n-hexylamine, n-octylamine) and at 50°C (all the amines) for 1–9 days. Obtained results can be applied to prepare N-alkylpectinamides of predicted DA varying the reaction time at the same reaction conditions (temperature, pectin/alkylamine ratio).

scholarly journals Experimental Design-Based Response Surface Methodology Optimization for Synthesis of β-Mercapto Carbonyl Derivatives as Antimycobacterial Drugs Catalyzed by Calcium Pyrophosphate

2014 ◽  
Vol 2014 ◽  
pp. 1-5 ◽  
Author(s):  
Younes Abrouki ◽  
Abdelkader Anouzla ◽  
Hayat Loukili ◽  
Jamal Bennazha ◽  
Rabiaâ Lotfi ◽  
...  
Keyword(s):  
Reaction Time ◽  
Response Surface ◽  
Product Formation ◽  
Reaction Model ◽  
Calcium Pyrophosphate ◽  
High Yield ◽  
Experimental Program ◽  
Reaction Yield ◽  
Reaction Conditions ◽  
Carbonyl Derivatives

A simple protocol for the efficient preparation of β-mercapto carbonyl derivatives as antimycobacterial drugs has been achieved via Thia-Michael reaction between chalcones derivatives and thiols in the presence of calcium pyrophosphate as a heterogeneous catalyst under mild reaction conditions. The central composite design was used to design an experimental program to provide data to model the effects of various factors on reaction yield (Y). The variables chosen were catalyst weight X1, reaction time X2, and solvent volume X3. The mathematical relationship of reaction yield on the three significant independent variables can be approximated by a nonlinear polynomial model. Predicted values were found to be in good agreement with experimental values. The optimum reaction conditions for reaction model (chalcone and thiophenol) obtained by response surface were applied to other substrates. This procedure provides several advantages such as high yield, clean product formation, and short reaction time.

Scalable Synthesis of Functionalized Ferrocenyl Azides and Amines Enabled by Flow Chemistry

2019 ◽  
Author(s):  
Merlin Kleoff ◽  
Johannes Schwan ◽  
Lisa Boeser ◽  
Bence Hartmayer ◽  
Mathias Christmann ◽  
...  
Keyword(s):  
Reaction Time ◽  
Heterogeneous Reaction ◽  
Reduction Process ◽  
Flow Chemistry ◽  
Subsequent Reaction ◽  
Scalable Synthesis ◽  
High Yields ◽  
Reactor Section

A scalable access to functionalized 1,1’- and 1,2-ferrocenyl azides has been realized in flow. By halogen‒lithium exchange of ferrocenyl halides and subsequent reaction with tosyl azide, a variety of functionalized ferrocenyl azides was obtained in high yields. To allow a scalable preparation of these potentially explosive compounds, an efficient flow protocol was developed accelerating the reaction time to minutes and circumventing accumulation of potentially hazardous intermediates. Switching from homogeneous to triphasic flow amidst process was key for handling a heterogeneous reaction mixture formed after a heated reactor section. The corresponding and synthetically versatile ferrocenyl amines were then prepared by a reliable reduction process.

Effects of salts on the kinetics of oxidation of alkenes by thallic salts in aqueous solutions

1981 ◽  
Vol 46 (3) ◽  
pp. 693-700 ◽  
Author(s):  
Milan Strašák ◽  
Jaroslav Majer
Keyword(s):  
Aqueous Solutions ◽  
Phase Transfer ◽  
Heterogeneous Reaction ◽  
Qualitative Model ◽  
Kinetic Effect ◽  
Tetraalkylammonium Salts ◽  
Reaction Conditions ◽  
Kinetics Of Oxidation ◽  
Kinetics Of ◽  
Heterogeneous Reaction Conditions

The kinetics of oxidation of alkenes by thallic sulphate in aqueous solutions, involving the two reaction steps-the hydroxythallation and the dethallation - was studied, and the effect of salts on the kinetics was examined; this made it possible to specify more precisely the reaction mechanism and to suggest a qualitative model of the reaction coordinate. It was found that in homogeneous as well as in heterogeneous reaction conditions, the reaction can be accelerated appreciably by adding tetraalkylammonium salts. These salts not only operate as catalysts of the phase transfer, but also exert a significant kinetic effect, which can be explained with a simplification in terms of a stabilization of the transition state of the reaction.

Study on the Synthesis of Isoamyl Acetate Catalyzed by Strong Acidic Cation Exchange Resin

2011 ◽  
Vol 396-398 ◽  
pp. 2411-2415 ◽  
Author(s):  
Ping Lan ◽  
Li Hong Lan ◽  
Tao Xie ◽  
An Ping Liao
Keyword(s):  
Acetic Acid ◽  
Reaction Time ◽  
Cation Exchanger ◽  
Cation Exchange Resin ◽  
Isoamyl Acetate ◽  
Molar Ratio ◽  
Esterification Reaction ◽  
Reaction Conditions ◽  
Optimum Reaction

Isoamyl acetate was synthesized from isoamylol and glacial acetic acid with strong acidic cation exchanger as catalyst. The effects of reaction conditions such as acid-alcohol ratio, reaction time, catalyst dosage to esterification reaction have been investigated and the optimum reaction conditions can be concluded as: the molar ratio of acetic acid to isoamylol 0.8:1, reaction time 2h, 25 % of catalyst (quality of acetic acid as benchmark). The conversion rate can reach up to 75.46%. The catalytic ability didn’t reduce significantly after reusing 10 times and the results showed that the catalyst exhibited preferably catalytic activity and reusability.

Study on Pretreatment of Dye Wastewater by Fenton Oxidation Process

2012 ◽  
Vol 627 ◽  
pp. 378-381
Author(s):  
Bi Rong Wang
Keyword(s):  
Reaction Time ◽  
Oxidation Process ◽  
Removal Rate ◽  
Fenton Oxidation ◽  
Dye Wastewater ◽  
Dyeing Wastewater ◽  
Reaction Conditions ◽  
Fenton Oxidation Process

Fenton pretreatment has been used for treating dye wastewater. The effects of the dos of H2O2 and FeSO4, reaction time and pH on the removal COD were investigated. It was found that, when the reaction conditions are as follows: COD 2850 mg/L dyeing wastewater, the dosage of H2O2 is 140mmol/L, FeSO4 17.02 mmol/L, pH 7.6, and reaction time 1.0 h, the CODcr of dye wastewater removal rate of up to 70%. Fenton pretreatment process of dye wastewater has a broad prospect.

scholarly journals Synthesis of propylene carbonate from urea and 1,2-propylene glycol over metal carbonates

2011 ◽  
Vol 17 (3) ◽  
pp. 323-331 ◽  
Author(s):  
Jiancheng Zhou ◽  
Wu Dongfang ◽  
Birong Zhang ◽  
Yali Guo
Keyword(s):  
Reaction Time ◽  
Propylene Glycol ◽  
Propylene Carbonate ◽  
Reaction Temperature ◽  
Reaction Conditions ◽  
Lead Carbonate ◽  
Synthetic Process ◽  
Metal Carbonates ◽  
Optimal Reaction ◽  
Mixed Carbonate

A series of single-metal carbonates and Pb-Zn mixed-metal carbonates were prepared as catalysts for alcoholysis of urea with 1,2-propylene glycol (PG) for the synthesis of propylene carbonate (PC). The mixed carbonates all show much better catalytic activities than the single carbonates, arising from a strong synergistic effect between the two crystalline phases, hydrozincite and lead carbonate. The mixed carbonate with Pb/Zn=1:2 gives the highest yield of PC, followed by the mixed carbonate with Pb/Zn=1:3. Furthermore, Taguchi method was used to optimize the synthetic process for improving the yield of PC. It is shown that the reaction temperature is the most significant factor affecting the yield of PC, followed by the reaction time, and that the optimal reaction conditions are the reaction time at 5 hours, the reaction temperature at 180 oC and the catalyst amount at 1.8 wt%, resulting in the highest PC yield of 96.3%.

Optimization and statistical analysis of sono-Fenton treated wastewater of food industry using reactor by response surface method

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Vijay A. Juwar ◽  
Ajit P. Rathod
Keyword(s):  
Reaction Time ◽  
Response Surface ◽  
Food Industry ◽  
Batch Reactor ◽  
Oxygen Demand ◽  
Volume Ratio ◽  
Cod Removal ◽  
Treated Wastewater ◽  
Experimental Result ◽  
Molar Ratio

Abstract The present study deals with the treatment of complex waste (WW) treated for removal of chemical oxygen demand (COD) of the food industry by a sono-Fenton process using a batch reactor. The response surface methodology (RSM) was employed to investigate the five independent variables, such as reaction time, the molar ratio of H2O2/Fe2+, volume ratio of H2O2/WW, pH of waste, and ultrasonic density on COD removal. The experimental data was optimized. The optimization yields the conditions: Reaction time of 24 min, HP:Fe molar ratio of 2.8, HP:WW volume ratio of 1.9 ml/L, pH of 3.6 and an ultrasonic density of 1.8 W/L. The predicted value of COD was 91% and the experimental result was 90%. The composite desirability value (D) of the predicted percent of COD removal at the optimized level of variables was close to one (D = 0.991).

Synthesis of a Ruthenium Complex Based on 2,6-Bis[1-(Pyridin-2-yl)-1H-Benzo[d]Imidazol-2-yl]Pyridine and Catalytic Oxidation of (1H-Benzo[d]-Imidazol-2-yl)Methanol to 1H-Benzo[d]Imidazole-2-Carbaldehyde with H2O2

2017 ◽  
Vol 41 (2) ◽  
pp. 88-92
Author(s):  
Shenggui Liu ◽  
Rongkai Pan ◽  
Wenyi Su ◽  
Guobi Li ◽  
Chunlin Ni
Keyword(s):  
Reaction Time ◽  
Catalytic Oxidation ◽  
Reaction Temperature ◽  
Ruthenium Complex ◽  
Reaction Conditions ◽  
Molar Ratios ◽  
Optimal Reaction

2,6-Bis[1-(pyridin-2-yl)-1H-benzo[d]-imidazol-2-yl]pyridine (bpbp), which has been synthesised by intramolecular thermocyclisation of N2,N6-bis[2-(pyridin-2-ylamino)phenyl]pyridine-2,6-dicarboxamide, reacts with sodium pyridine-2,6-dicarboxylate (pydic) and RuCl3 to give [Ru(bpbp)(pydic)] which can catalyse the oxidation of (1H-benzo[d]imidazol-2-yl)methanol to 1H-benzo[d]imidazole-2-carbaldehyde by H2O2. The optimal reaction conditions were: molar ratios of catalyst to substrate to H2O2 set at 1: 1000: 3000; reaction temperature 50 °C; reaction time 5 h. The yield of (1H-benzo[d]imidazol-2-yl) methanol was 70%.

scholarly journals Biodiesel Production from a Novel Nonedible Feedstock, Soursop (Annona muricata L.) Seed Oil

Energies ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 2562 ◽  
Author(s):  
Chia-Hung Su ◽  
Hoang Nguyen ◽  
Uyen Pham ◽  
My Nguyen ◽  
Horng-Yi Juan
Keyword(s):  
Reaction Time ◽  
Seed Oil ◽  
Biodiesel Production ◽  
Molar Ratio ◽  
Annona Muricata ◽  
Reaction Conditions ◽  
Biodiesel Feedstock ◽  
Acid Catalyzed ◽  
American Society ◽  
Optimal Reaction

This study investigated the optimal reaction conditions for biodiesel production from soursop (Annona muricata) seeds. A high oil yield of 29.6% (w/w) could be obtained from soursop seeds. Oil extracted from soursop seeds was then converted into biodiesel through two-step transesterification process. A highest biodiesel yield of 97.02% was achieved under optimal acid-catalyzed esterification conditions (temperature: 65 °C, 1% H2SO4, reaction time: 90 min, and a methanol:oil molar ratio: 10:1) and optimal alkali-catalyzed transesterification conditions (temperature: 65 °C, reaction time: 30 min, 0.6% NaOH, and a methanol:oil molar ratio: 8:1). The properties of soursop biodiesel were determined and most were found to meet the European standard EN 14214 and American Society for Testing and Materials standard D6751. This study suggests that soursop seed oil is a promising biodiesel feedstock and that soursop biodiesel is a viable alternative to petrodiesel.

scholarly journals Production of Aspartame by Immobilized Thermolysin

2019 ◽  
pp. 1232-1239
Author(s):  
Mohammed A Alsoufi ◽  
Raghad A. Aziz
Keyword(s):  
Reaction Time ◽  
Immobilized Enzyme ◽  
Bentonite Clay ◽  
Optimum Temperature ◽  
Initial Activity ◽  
Reaction Conditions ◽  
Original Activity ◽  
Ph Profile ◽  
Full Activity ◽  
Main Activity

The aim of this study was the production of aspartame by using immobilized thermolysin in bentonite clay. The yield of immobilized thermolysin in bentonite was 92% of the original enzyme amount. pH profile of free and immobilized enzyme was 7.0 and 7.5 respectively which was stable at 6.5-9.0 for 30min. The optimum temperature of both enzymes was 50°C, while they were stable at 65°C for 30min. however, they lost 52.73 and 61.72% from its main activity at 80°C respectively. Immobilized thermolysin has retained all activity within 27 days, but it kept 68.27% of initial activity when stored for 60 days at 4°C whereas, it retained a full activity after 20 continue usage. In addition, it retained 86.53% of its original activity after 30 continuing usages. The yield of produced aspartame was increased with reaction time; it was 9% after 1h and increased gradually to 100% after 10h at reaction conditions.

Sign in / Sign up

Export Citation Format

Share Document