scholarly journals A simulation strategy to determine the mechanical behaviour of cork-rubber composite pads for vibration isolation

2021 ◽  
Vol 24 (1) ◽  
pp. 80-88
Author(s):  
Helena Lopes ◽  
Susana P. Silva ◽  
José Machado
Keyword(s):  
Regression Models ◽  
Vibration Isolation ◽  
Dynamic Stiffness ◽  
Experimental Tests ◽  
Compression Modulus ◽  
Element Analysis ◽  
Rubber Material ◽  
Rubber Compounds ◽  
Simulation Strategy ◽  
Mathematical Techniques

The present work aimed to determine the performance of new cork-rubber composites, applying a modelling-based approach. The static and dynamic behaviour under compression of new composite isolation pads was determined using mathematical techniques. Linear regression was used to estimate apparent compression modulus and dynamic stiffness coefficient of compounds samples based on the effect of fillers, cork and other ingredients. Using the results obtained by regression models, finite element analysis (FEA) was applied to determine the behaviour of the same cork-rubber material but considering samples with different dimensions. The majority of the regression models presented R2 values above 90%. Also, a good agreement was found between the results obtained by the presented approach and previous experimental tests. Based on the developed methodology, the compression behaviour of new cork-rubber compounds can be accessed, improving product development stages.

Combined stiffness characteristic of metal rubber material under vibration loads

2019 ◽  
Vol 233 (17) ◽  
pp. 6076-6088 ◽  
Author(s):  
Hailong Fu ◽  
Zhengli Hua ◽  
Longqing Zou ◽  
Yue Wang ◽  
Jianbin Ye
Keyword(s):  
Energy Dissipation ◽  
Vibration Isolation ◽  
Influence Factors ◽  
Experimental Tests ◽  
Individual Element ◽  
Rubber Material ◽  
Static Tests ◽  
Metal Rubber ◽  
Vibration Loads ◽  
The Individual

Metal rubber is one kind of elastic cellular metal material, which is widely used in vibration isolation environment for its excellent properties of elasticity, energy dissipation, and environmental adaptability. However, the stiffness range of one single metal rubber is restricted, which limits its ability of vibration isolation, especially under the complex vibration loads. In this paper, a method of spatial overlay combination is presented to widen the range of the stiffness of metal rubber material. The contact behavior of the metal spiral rolls and the influence factors of manufacture to the stiffness are investigated according to the micro-spring theory and the energy dissipation theory. The static tests under cycling loading are conducted to obtain the average stiffness and the equivalent stiffness of the combined metal rubber. After the comparisons, the combined metal rubber has a better stiffness range than the individual element. The diameter of metal wire and the relative density of metal rubber are two important influence factors to the combined stiffness, which are verified by the experimental tests and finite element simulation.

scholarly journals Predicting the Dynamic Behaviour of Hydrobushings

2005 ◽  
Vol 12 (2) ◽  
pp. 91-107 ◽  
Author(s):  
N. Gil-Negrete ◽  
A. Rivas ◽  
J. Viñolas
Keyword(s):  
Finite Element ◽  
Fluid Flow ◽  
Dynamic Behaviour ◽  
Dynamic Stiffness ◽  
Experimental Tests ◽  
Finite Element Code ◽  
Practical Application ◽  
Rubber Material ◽  
Maximum Value ◽  
Fluid Properties

A novel and promising approach for the prediction of the dynamic stiffness of hydrobushings is presented, combining Finite Element and CFD methods. The rubber structure of the mount is modelled in ABAQUS and the flow of fluid through the inertia track is calculated in FLUENT. The obtained results from the latter simulation are incorporated in the finite element code for the final stiffness prediction. The calculation is very sensitive to both rubber and fluid properties. The dynamic behaviour of rubber material has accurately been characterised with a new simple shear specimen in a forced non-resonant test.Satisfactory results are obtained when comparing numerical simulations to experimental tests in a practical application. Discrepancies between simulations and tests are mainly due to the simplifications assumed when creating the model. Nevertheless, stiffness of the mount is well predicted and so is the damping, although the frequency at which its maximum value is achieved is underestimated by 4–6 Hz, result that could be improved if non-stationary boundary conditions were considered when solving the fluid flow and incorporating it to the finite element code.

Design and analysis of a vibration isolation system with cam–roller–spring–rod mechanism

2021 ◽  
pp. 107754632110005
Author(s):  
Yonglei Zhang ◽  
Guo Wei ◽  
Hao Wen ◽  
Dongping Jin ◽  
Haiyan Hu
Keyword(s):  
Vibration Isolation ◽  
Dynamic Stiffness ◽  
Experimental Studies ◽  
Excitation Amplitude ◽  
Isolation System ◽  
Vibration Isolation System ◽  
Stiffness Characteristic ◽  
Negative Stiffness Mechanism ◽  
Isolation Systems ◽  
Vibration Isolation Performance

The vibration isolation system using a pair of oblique springs or a spring-rod mechanism as a negative stiffness mechanism exhibits a high-static low-dynamic stiffness characteristic and a nonlinear jump phenomenon when the system damping is light and the excitation amplitude is large. It is possible to remove the jump via adjusting the end trajectories of the above springs or rods. To realize this idea, the article presents a vibration isolation system with a cam–roller–spring–rod mechanism and gives the detailed numerical and experimental studies on the effects of the above mechanism on the vibration isolation performance. The comparative studies demonstrate that the vibration isolation system proposed works well and outperforms some other vibration isolation systems.

scholarly journals A New Approach of Soft Joint Based on a Cable-Driven Parallel Mechanism for Robotic Applications

Mathematics ◽  
2021 ◽  
Vol 9 (13) ◽  
pp. 1468
Author(s):  
Luis Nagua ◽  
Carlos Relaño ◽  
Concepción A. Monje ◽  
Carlos Balaguer
Keyword(s):  
Parallel Mechanism ◽  
Degrees Of Freedom ◽  
Kinematic Model ◽  
Experimental Tests ◽  
Humanoid Robots ◽  
Inverse Kinematic ◽  
Element Analysis ◽  
New Approach ◽  
Flexible Polymer ◽  
The Mathematical Model

A soft joint has been designed and modeled to perform as a robotic joint with 2 Degrees of Freedom (DOF) (inclination and orientation). The joint actuation is based on a Cable-Driven Parallel Mechanism (CDPM). To study its performance in more detail, a test platform has been developed using components that can be manufactured in a 3D printer using a flexible polymer. The mathematical model of the kinematics of the soft joint is developed, which includes a blocking mechanism and the morphology workspace. The model is validated using Finite Element Analysis (FEA) (CAD software). Experimental tests are performed to validate the inverse kinematic model and to show the potential use of the prototype in robotic platforms such as manipulators and humanoid robots.

On-Site Experimental Testing to Study the Vibration of Composite Floors

2014 ◽  
Vol 601 ◽  
pp. 231-234
Author(s):  
Cristian Lucian Ghindea ◽  
Dan Cretu ◽  
Monica Popescu ◽  
Radu Cruciat ◽  
Elena Tulei
Keyword(s):  
Dynamic Characteristics ◽  
Experimental Testing ◽  
Concrete Slab ◽  
Human Perception ◽  
Experimental Tests ◽  
International Standards ◽  
Structural Element ◽  
Element Analysis ◽  
Floor Slabs ◽  
Composite Floors

As a general trend, in order to reduce material consumption or to reduce the mass of the structures, composite floor slabs solutions are used to achieve large spans floor slabs. This solutions led to floors sensitive to vibrations induced generally by human activities. As a verification of the design concepts of the composite floors, usually, it is recommended a further examination of the floor after completion by experimental tests. Although the experimental values of the dynamic response of the floor are uniquely determined, the processing can take two directions of evaluation. The first direction consist in determining the dynamic characteristics of the floor and their comparison with the design values. Another way that can be followed in the processing of the experimental results is to consider the human perception and comfort to the vibration on floors. The paper aims to present a case study on a composite floor, with steel beams and concrete slab, tested on-site. Both aspects of data processing are analyzed, in terms of the structural element, and in terms of the effect on human perception and comfort. Experimentally obtained values for the dynamic characteristics of the floor are compared with numerical values from finite element analysis, while the second type of characteristic values are compared with various human comfort threshold values found in international standards.

Dynamic Analysis of Helical Milling Unit Based on Virtual Machine Tool

2011 ◽  
Vol 188 ◽  
pp. 463-468 ◽  
Author(s):  
Xu Da Qin ◽  
Qi Wang ◽  
H.Y. Wang ◽  
Song Hua
Keyword(s):  
Machine Tool ◽  
Virtual Machine ◽  
Dynamic Stiffness ◽  
Three Dimensional ◽  
Geometrical Model ◽  
Helical Milling ◽  
Response Analysis ◽  
Computer Simulation Model ◽  
Element Analysis ◽  
Virtual Machine Tool

The virtual prototype is a computer simulation model of the physical product that can be analyzed like a real machine. This paper studies the helical milling unit based on the virtual machine tool. The helical milling unit is first designed according to the kinematics of the helical milling. The main parts of the equipment include rotating mechanism, orbital agency and radial offset organization. Based on the feasibility analysis of the structure, the three-dimensional geometrical model is built in the Solidworks software. The key parts in the model are separated from the device and introduced into the finite element analysis (FEA) software, according to the cutting loads tested from experiment, static and dynamic modal analysis and harmonic response analysis are carried out for the key parts of this device. The results show that the static and dynamic stiffness can meet design requirement.

Design of a Miniaturized Pneumatic Vibration Isolator With High-Static-Low-Dynamic Stiffness

2015 ◽  
Vol 137 (4) ◽  
Author(s):  
Yuhu Shan ◽  
Wenjiang Wu ◽  
Xuedong Chen
Keyword(s):  
Vibration Isolation ◽  
Dynamic Stiffness ◽  
Structure Design ◽  
Negative Stiffness ◽  
Vibration Isolator ◽  
Load Bearing Capacity ◽  
Compact Structure ◽  
Chamber Volume ◽  
Isolation Systems ◽  
Magnetic Rings

In the ultraprecision vibration isolation systems, it is desirable for the isolator to have a larger load bearing capacity and a broader isolation bandwidth simultaneously. Generally, pneumatic spring can bear large load and achieve relatively low natural frequency by enlarging its chamber volume. However, the oversized isolator is inconvenient to use and might cause instability. To reduce the size, a miniaturized pneumatic vibration isolator (MPVI) with high-static-low-dynamic stiffness (HSLDS) is developed in this paper. The volume of proposed isolator is minimized by a compact structure design that combines two magnetic rings in parallel with the pneumatic spring. The two magnetic rings are arranged in the repulsive configuration and can be mounted into the chamber to provide the negative stiffness. Then dynamic model of the developed MPVI is built and the isolation performances are analyzed. Finally, experiments on the isolator with and without the magnetic rings are conducted. The final experimental results are consistent with the dynamical model and verify the effectiveness of the developed vibration isolator.

Gluconeogenesis from labeled carbon: estimating isotope dilution

1986 ◽  
Vol 250 (3) ◽  
pp. E296-E305 ◽  
Author(s):  
J. K. Kelleher
Keyword(s):  
Steady State ◽  
Isotope Dilution ◽  
Experimental Tests ◽  
Tca Cycle ◽  
Tricarboxylic Acid ◽  
Complex Model ◽  
Acetyl Coa ◽  
The Tca Cycle ◽  
Carbon Compounds ◽  
Mathematical Techniques

To estimate the rate of gluconeogenesis from steady-state incorporation of labeled 3-carbon precursors into glucose, isotope dilution must be considered so that the rate of labeling of glucose can be quantitatively converted to the rate of gluconeogenesis. An expression for the value of this isotope dilution can be derived using mathematical techniques and a model of the tricarboxylic acid (TCA) cycle. The present investigation employs a more complex model than that used in previous studies. This model includes the following pathways that may affect the correction for isotope dilution: 1) flux of 3-carbon precursor to the oxaloacetate pool via acetyl-CoA and the TCA cycle; 2) flux of 4- or 5-carbon compounds into the TCA cycle; 3) reversible flux between oxaloacetate (OAA) and pyruvate and between OAA and fumarate; 4) incomplete equilibrium between OAA pools; and 5) isotope dilution of 3-carbon tracers between the experimentally measured pool and the precursor for the TCA-cycle OAA pool. Experimental tests are outlined which investigators can use to determine whether these pathways are significant in a specific steady-state system. The study indicated that flux through these five pathways can significantly affect the correction for isotope dilution. To correct for the effects of these pathways an alternative method for calculating isotope dilution is proposed using citrate to relate the specific activities of acetyl-CoA and OAA.

Sign in / Sign up

Export Citation Format

Share Document