scholarly journals INVESTIGATION OF THE GEOMECHANICAL STATE OF SOFT ADJOINING ROCKS UNDER PROTECTIVE CONSTRUCTIONS

2021 ◽  
Vol 36 (4) ◽  
pp. 61-71
Author(s):  
Serhii Nehrii ◽  
Tetiana Nehrii ◽  
Oksana Zolotarova ◽  
Serhii Volkov
Keyword(s):  
Physical And Mechanical Properties ◽  
New Approach ◽  
Soft Rocks ◽  
The Face ◽  
Geomechanical State ◽  
Rock Mass Failure ◽  
The Stability ◽  
Seam Mining ◽  
Mine Roadways

The conditions of coal seam mining in the mines of Ukraine have been considered. The problem of conducting coal mining by longwalls in the conditions of soft adjoining rocks, which concerns the protection of mine roadways located near the face, has been revealed. In such conditions, the existing protective constructions are ineffective due to the fact that they yield and get pressed into the soft rocks of the footwall. This indicated the need for research into the geomechanical state of soft rocks of the footwall. According to the results of known studies on the mechanism of rock mass failure around roadways and the data of physical and mechanical properties of the coal mass, which is represented by soft rocks, the correlation dependence has been obtained, the use of which allowed for the determination of the parameters of the rock deformation diagram and the establishment of the stability criterion of footwall rocks under the protection means and stability conditions of the geotechnical system “protective construction – adjoining rocks.” They are the basis of a new approach to ensure the stability of the roadways, which are supported behind the faces, by controlling the stress state in the system “protective construction – adjoining rocks.” This may be the basis for the development of new methods of protecting roadways in conditions of soft adjoining rocks.

scholarly journals Determination of transmission reliability margin for brownout

AIMS Energy ◽  
2021 ◽  
Vol 9 (5) ◽  
pp. 1009-1026
Author(s):  
Awatif Nadia ◽  
◽  
Md. Sanwar Hossain ◽  
Md. Mehedi Hasan ◽  
Sinthia Afrin ◽  
...  
Keyword(s):  
Smart Grids ◽  
Reactive Power ◽  
Severe Problem ◽  
New Approach ◽  
Transmission Reliability ◽  
Detailed Assessment ◽  
The Stability ◽  
Power Shortages ◽  
Margin Analysis

<abstract> <p>Power shortage is a severe problem in developing countries that are rolling to blackout, but today smart grids have the scope to avoid entire blackouts by transforming them into brownouts. A brownout is an under-voltage condition where the AC supply drops below the nominal value (120 V or 220 V) by about 10%. In a power system network, power shortages or disturbances can occur at any time, and the reliability margin analysis is essential to maintain the stability of the system. Transmission reliability margin (TRM) is a margin that keeps the network secure during any occurrence of disturbance. This paper presents a new approach to compute TRM in the case of brownout. The detailed assessment of TRM largely depends on the estimation of the available transfer power (ATC). In this method, the ATC of the system is calculated considering the effect of alternating current (AC) and direct current (DC) reactive power (Q) flow (DCQF). The entire procedure is carried out for the multi-transaction IEEE-6 bus system, and the results are compared to the current efficiency justification method. Numerical results demonstrate that the proposed technique is an effective alternative for calculating the TRM and is valid compared to the existing technique.</p> </abstract>

AN ERP-BASED BCI USING AN ODDBALL PARADIGM WITH DIFFERENT FACES AND REDUCED ERRORS IN CRITICAL FUNCTIONS

2014 ◽  
Vol 24 (08) ◽  
pp. 1450027 ◽  
Author(s):  
JING JIN ◽  
BRENDAN Z. ALLISON ◽  
YU ZHANG ◽  
XINGYU WANG ◽  
ANDRZEJ CICHOCKI
Keyword(s):  
Event Related Potentials ◽  
Oddball Paradigm ◽  
Repetition Effects ◽  
New Approach ◽  
Computer Interfaces ◽  
Single Face ◽  
The Face ◽  
Related Potentials ◽  
The Stability ◽  
Face Pattern

Recent research has shown that a new face paradigm is superior to the conventional "flash only" approach that has dominated P300 brain–computer interfaces (BCIs) for over 20 years. However, these face paradigms did not study the repetition effects and the stability of evoked event related potentials (ERPs), which would decrease the performance of P300 BCI. In this paper, we explored whether a new "multi-faces (MF)" approach would yield more distinct ERPs than the conventional "single face (SF)" approach. To decrease the repetition effects and evoke large ERPs, we introduced a new stimulus approach called the "MF" approach, which shows different familiar faces randomly. Fifteen subjects participated in runs using this new approach and an established "SF" approach. The result showed that the MF pattern enlarged the N200 and N400 components, evoked stable P300 and N400, and yielded better BCI performance than the SF pattern. The MF pattern can evoke larger N200 and N400 components and more stable P300 and N400, which increase the classification accuracy compared to the face pattern.

scholarly journals Determination of economically viable option of liquidation the consequences of external dump deformation

2021 ◽  
Vol 280 ◽  
pp. 08014
Author(s):  
Yevheniy Babets ◽  
Oleh Anisimov ◽  
Oleksandr Shustov ◽  
Vitalina Komirna ◽  
Iryna Melnikova
Keyword(s):  
Mechanical Properties ◽  
Physical And Mechanical Properties ◽  
Safety Factors ◽  
Viable Option ◽  
The Third ◽  
The Stability ◽  
The Cost ◽  
Technical And Economic Indicators ◽  
Processing Enterprise

The safety factors for different variants of operation development were obtained, on the basis of which the technical and economic indicators were established and the most expedient way of restoration of dump operations in conditions of the formed landslide was chosen. The solutions were proposed for the external dump No 2 of the Central Ore Mining and Processing Enterprise (COMPE), that allow to continue its future operation. When working in the conditions of the formed landslide, three variants of the further dump operation are modeled: the first one - with landslide removal and unloading of the upper dump horizons, the second one - without landslide removal and involvement of disturbed lands in land allotment, the third one - with the landslide loading. Based on the built sections of the dump and defined physical and mechanical properties, the stability factors were obtained for different options of the operation development, which made it possible to determine the appropriate option to eliminate the effects of the dump slide deformations. As a result of the calculations, the cost flows for each of the proposed options of the formation of the end contour of the dump No 2 are determined.

Em transe-to

2020 ◽  
Vol 2 (1) ◽  
pp. 32-55
Author(s):  
Natalia Christofoletti Barrenha
Keyword(s):  
The Face ◽  
The Stability ◽  
The City

This text seeks to explore the Argentine films Castro (Alejo Moguillansky, 2009) and El asaltante (Pablo Fendrik, 2007) from within the displacement of their characters through the city. This transit configures the organising element of the plots, determining the direction and rhythm of events. The escape motto will structure the film analyses, which are also twinned by the sensory apprehension that comes from the spaces they travel through. The notion of escape, as explored by Esteban Dipaola in Argentine cinema of the 1990s, continues to throb in mid-to-late 2000s production, and in these films represents the means by which the protagonists deploy critical attitudes—sometimes radical and explosive, sometimes silent—in the face of fixed notions, suggesting some scepticism about the “stability” and “order” that they (dis)encounter in normality. RESUMEN Este texto busca explorar los largometrajes argentinos Castro (Alejo Moguillansky, 2009) y El asaltante (Pablo Fendrik, 2007) a partir del desplazamiento de sus personajes por la ciudad. El transitar se configura como elemento organizador de las tramas, determinando la dirección y el ritmo de los acontecimientos. El tema de la fuga irá estructurando los análisis de las películas, las cuales también están relacionadas por la aprehensión sensorial que hacen de los espacios que recorren. La noción de fuga, tal y como fue explorada por Esteban Dipaola en el cine argentino de los años 90, continúa vigente en la producción de mediados/fines de la primera década del siglo XXI, y en estas películas es el recurso por medio del cual los protagonistas despliegan actitudes críticas – a veces radicales y explosivas, y a veces silenciosas – frente a nociones convencionales, lo cual hace pensar que existe un cierto escepticismo con relación a la “estabilidad” y al “orden” que ellos (des)encuentran en la normalidad. RESUMO Este texto busca explorar os longas-metragens argentinos Castro (Alejo Moguillansky, 2009) e El asaltante (Pablo Fendrik, 2007) a partir do deslocamento de seus personagens pela cidade. O transitar configura-se como elemento organizador das tramas, determinando a direção e o ritmo dos acontecimentos. O mote da fuga estruturará as análises dos filmes, os quais também se irmanam pela apreensão sensorial que fazem dos espaços que percorrem. A noção de fuga, conforme explorada por Esteban Dipaola no cinema argentino da década de 1990, continua a pulsar na produção de meados/fins dos anos 2000, e é, nestes filmes, o recurso através do qual os protagonistas desdobram atitudes críticas – às vezes radicais e explosivas, às vezes silenciosas – diante de noções fixas, sugerindo certo ceticismo em relação à “estabilidade” e à “ordem” que eles (des)encontram na normalidade.

Determination of Combined and Second Order Factor Effects for Simultaneous Optimization of Physical and Mechanical Properties of NR/BR Blend System

2014 ◽  
Vol 42 (4) ◽  
pp. 290-304
Author(s):  
Rajarajan Aiyengar ◽  
Jyoti Divecha
Keyword(s):  
Physical And Mechanical Properties ◽  
Second Order ◽  
Simultaneous Optimization ◽  
Order Effects ◽  
Elongation At Break ◽  
Five Factors ◽  
Rubber Compounds ◽  
Polybutadiene Rubber ◽  
Contour Plots

ABSTRACT The blends of natural rubber (NR), polybutadiene rubber (BR), and other forms of rubbers are widely used for enhancing the mechanical and physical properties of rubber compounds. Lots of work has been done in conditioning and mixing of NR/BR blends to improve the properties of its rubber compounds and end products such as tire tread. This article employs response surface methodology designed experiments in five factors; high abrasion furnace carbon black (N 330), aromatic oil, NR/BR ratio, sulfur, and N-oxydiethylene-2-benzothiazole sulfenamide for determination of combined and second order effects of the significant factors leading to simultaneous optimization of the NR/BR blend system. One of the overall optimum of eight properties existed at carbon 44 phr, oil 6.1 phr, NR/BR 78/22 phr with the following values of properties: tensile strength (22 MPa), elongation at break (528%), tear resistance (30 kg/mm), rebound resilience (67%), moderate hardness (68 International rubber hardness degrees) with low heat buildup (17 °C), permanent set (12%), and abrasion loss (57 mm3). More optimum combinations can easily be determined from the NR/BR blend system models contour plots.

Basic set of experiments for determination of mechanical properties of sand

2014 ◽  
Vol 62 (1) ◽  
pp. 129-137
Author(s):  
A. Sawicki ◽  
J. Mierczyński
Keyword(s):  
Mechanical Properties ◽  
Soil Mechanics ◽  
Physical And Mechanical Properties ◽  
Local Strain ◽  
Initial State ◽  
Laboratory Equipment ◽  
Additional Information ◽  
Basic Set ◽  
Initial Anisotropy

Abstract A basic set of experiments for the determination of mechanical properties of sands is described. This includes the determination of basic physical and mechanical properties, as conventionally applied in soil mechanics, as well as some additional experiments, which provide further information on mechanical properties of granular soils. These additional experiments allow for determination of steady state and instability lines, stress-strain relations for isotropic loading and pure shearing, and simple cyclic shearing tests. Unconventional oedometric experiments are also presented. Necessary laboratory equipment is described, which includes a triaxial apparatus equipped with local strain gauges, an oedometer capable of measuring lateral stresses and a simple cyclic shearing apparatus. The above experiments provide additional information on soil’s properties, which is useful in studying the following phenomena: pre-failure deformations of sand including cyclic loading compaction, pore-pressure generation and liquefaction, both static and caused by cyclic loadings, the effect of sand initial anisotropy and various instabilities. An important feature of the experiments described is that they make it possible to determine the initial state of sand, defined as either contractive or dilative. Experimental results for the “Gdynia” model sand are shown.

The Dudley Lee Case: A new approach to factual causation and its implications for transformative jurisprudence

2017 ◽  
Vol 30 (1) ◽  
pp. 273-289
Author(s):  
Anmari Meerkotter
Keyword(s):  
Case Note ◽  
Constitutional Court ◽  
Recent Contribution ◽  
New Approach ◽  
State Accountability ◽  
The Law ◽  
Transformative Impact ◽  
Constitutional Jurisprudence ◽  
Law Of Delict

The Constitutional Court (CC) judgment of Lee v Minister of Correction Services 2013 2SA 144 (CC) is a recent contribution to transformative constitutional jurisprudence in the field of the law of delict. This matter turned on the issue of factual causation in the context of wrongful and negligent systemic omissions by the state. In this case note, I explore the law relating to this element of delictual liability with specific regard to the traditional test for factual causation – the conditio sine qua non (‘but-for’) test. In particular, I note the problems occasioned by formalistic adherence to this test in the context of systemic state omissions as evidenced by the SCA judgment in the same matter. I also consider the manner in which English courts have addressed this problem. Thereafter, I analyse the CC’s broader approach to the determination of factual causation as one based on common sense and justice. I argue that this approach endorses a break from a formalistic application of the test and constitutes a step towards an approach which resonates with the foundational constitutional values of freedom, dignity and equality. Furthermore, it presents an appropriate solution to the problems associated with factual causation where systemic omissions are concerned. I then consider the transformative impact of the Lee judgment. In particular, I argue that the broader enquiry favoured by the CC facilitates the realisation of constitutionally guaranteed state accountability, and amounts to an extension of the existing norm of accountability jurisprudence. Hence, I contend that the judgment presents a further effort by the Constitutional Court to effect wholesale the constitutionalisation of the law of delict, as well as a vindicatory tool to be used by litigants who have been adversely affected by systemic state omissions.

Host-Guest Interactions on Electrode Surfaces for Immobilization of Molecular Catalysts

2020 ◽  
Author(s):  
Laurent Sévery ◽  
Jacek Szczerbiński ◽  
Mert Taskin ◽  
Isik Tuncay ◽  
Fernanda Brandalise Nunes ◽  
...  
Keyword(s):  
Aqueous Media ◽  
Heterogeneous Systems ◽  
Catalytic Systems ◽  
New Approach ◽  
Molecular Systems ◽  
Electrode Surfaces ◽  
Catalytic Surfaces ◽  
Oxide Electrodes ◽  
The Stability ◽  
Molecular Catalysts

The strategy of anchoring molecular catalysts on electrode surfaces combines the high selectivity and activity of molecular systems with the practicality of heterogeneous systems. The stability of molecular catalysts is, however, far less than that of traditional heterogeneous electrocatalysts, and therefore a method to easily replace anchored molecular catalysts that have degraded could make such electrosynthetic systems more attractive. Here, we apply a non-covalent “click” chemistry approach to reversibly bind molecular electrocatalysts to electrode surfaces via host-guest complexation with surface-anchored cyclodextrins. The host-guest interaction is remarkably strong and allows the flow of electrons between the electrode and the guest catalyst. Electrosynthesis in both organic and aqueous media was demonstrated on metal oxide electrodes, with stability on the order of hours. The catalytic surfaces can be recycled by controlled release of the guest from the host cavities and readsorption of fresh guest. This strategy represents a new approach to practical molecular-based catalytic systems.

Automatic Determination of Optimal FIB Operations for Improved Circuit Probing and Fast Reconfiguration

2000 ◽  
Author(s):  
Romain Desplats ◽  
Timothee Dargnies ◽  
Jean-Christophe Courrege ◽  
Philippe Perdu ◽  
Jean-Louis Noullet
Keyword(s):  
Integrated Circuit ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Semiconductor Devices ◽  
Front Side ◽  
Automatic Determination ◽  
Metal Line ◽  
New Approach ◽  
Metal Layers

Abstract Focused Ion Beam (FIB) tools are widely used for Integrated Circuit (IC) debug and repair. With the increasing density of recent semiconductor devices, FIB operations are increasingly challenged, requiring access through 4 or more metal layers to reach a metal line of interest. In some cases, accessibility from the front side, through these metal layers, is so limited that backside FIB operations appear to be the most appropriate approach. The questions to be resolved before starting frontside or backside FIB operations on a device are: 1. Is it do-able, are the metal lines accessible? 2. What is the optimal positioning (e.g. accessing a metal 2 line is much faster and easier than digging down to a metal 6 line)? (for the backside) 3. What risk, time and cost are involved in FIB operations? In this paper, we will present a new approach, which allows the FIB user or designer to calculate the optimal FIB operation for debug and IC repair. It automatically selects the fastest and easiest milling and deposition FIB operations.

Sign in / Sign up

Export Citation Format

Share Document